New EKO Builds 4/7/12 18946 - Supports the new Cisco's

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8, 9
Author Message
dehrle
DD-WRT Novice


Joined: 28 Jul 2012
Posts: 9

PostPosted: Mon Jul 30, 2012 17:00    Post subject: 610N v2 - went back to 15962 Reply with quote
I changed my code back to 15962. I thought about converting to an E3000. Reason: Half my configuration disappeared (no reset and uptime was good). My IP address range was 192.168.0.0/24 and it became 192.168.1.0/24, my QoS was missing; but my hostname, and wireless configurations were unchanged.
Sponsor
axim
DD-WRT Novice


Joined: 20 Aug 2012
Posts: 2

PostPosted: Mon Aug 20, 2012 22:00    Post subject: Reply with quote
Curious if anyone is having issues mounting via USB on the E1550 -- I've tried extfs2/3 and NTFS with no luck. I've used the following version:

dd-wrt.v24-18946_NEWD-2_K2.6_std_usb_nas-nv60k.bin

And here's the output of the USB tab on the router:

--- /dev/discs/disc0/disc
Block device, size 298.1 GiB (320072933376 bytes)
DOS/MBR partition map
Partition 1: 298.1 GiB (320072932864 bytes, 625142447 sectors from 1)
Type 0xEE (EFI GPT protective)
GPT partition map, 128 entries
Disk size 298.1 GiB (320072933376 bytes, 625142448 sectors)
Disk GUID 1E26CD03-90B0-C94E-8DFC-F5227514DE0B
Partition 1: 9.766 GiB (10485760000 bytes, 20480000 sectors from 2048)
Type Basic Data (GUID A2A0D0EB-E5B9-3344-87C0-68B6B72699C7)
Partition Name ""
Partition GUID 9F94BC8B-19AA-DC40-A4F6-D4D25BF4AAE7
Ext3 file system
UUID BB68C4A9-0D91-475B-A52B-32F9AC461D6C (DCE, v4)
Volume size 9.766 GiB (10485760000 bytes, 2560000 blocks of 4 KiB)
Partition 2: 24.65 GiB (26470252544 bytes, 51699712 sectors from 20482048)
Type Basic Data (GUID A2A0D0EB-E5B9-3344-87C0-68B6B72699C7)
Partition Name ""
Partition GUID 98B837BA-88D2-924A-A39D-6B06242DCBCF
Ext3 file system
UUID 23CEEFFB-BA32-4C64-B55B-600A29821849 (DCE, v4)
Volume size 24.65 GiB (26470252544 bytes, 6462464 blocks of 4 KiB)
Partition 3: 214.8 GiB (230686720000 bytes, 450560000 sectors from 72181760)
Type Basic Data (GUID A2A0D0EB-E5B9-3344-87C0-68B6B72699C7)
Partition Name ""
Partition GUID C3B6414C-B9B5-314E-9D44-9308510991C2
Ext3 file system
Volume name "3"
UUID CE424231-DC4A-4FBF-B882-DD9032385661 (DCE, v4)
Volume size 214.8 GiB (230686720000 bytes, 56320000 blocks of 4 KiB)
Partition 4: 48.83 GiB (52428800000 bytes, 102400000 sectors from 522741760)
Type Basic Data (GUID A2A0D0EB-E5B9-3344-87C0-68B6B72699C7)
Partition Name ""
Partition GUID 46B2B2E1-317D-914A-80E1-FD536536DD55
Ext3 file system
Volume name "4"
UUID 41E1F0EE-53BC-440D-A1BD-A04C5DD1D8EC (DCE, v4)
Volume size 48.83 GiB (52428800000 bytes, 12800000 blocks of 4 KiB)
Partition 5: unused
Status: Not mounted
Status: Not mounted

Any insight would be great, cheers!
axim
DD-WRT Novice


Joined: 20 Aug 2012
Posts: 2

PostPosted: Tue Aug 21, 2012 21:35    Post subject: Reply with quote
It would appear that any ext3/2 file systems won't mount, or NTFS formatted through GPART, but when I format it NTFS in disk utility on OSX.. it automounts that volume.

So with that said managed to get everything installed & Transmission running stable, only real issue is streaming over SMB which is fine for anything that isn't high bitrate.. so really the only thing life would be to have ext3 working which I've heard has around 3x the throughput.

Also for others w/ this router, the only way I could get Optware installed was via:
Quote:
wget http://www.3iii.dk/linux/optware/optware-install-ddwrt.sh -O /tmp/optware-install.sh
sh /tmp/optware-install.sh
skyhi1977
DD-WRT Novice


Joined: 12 Sep 2012
Posts: 8

PostPosted: Thu Sep 13, 2012 14:38    Post subject: Reply with quote
install dd-wrt.v24-18946_NEWD-2_K2.6_mini.bin and then dd-wrt.v24-18946_NEWD-2_K2.6_big.bin on my Belkin F7D8301, so far the router run great. Both 2.4Ghz and 5Ghz work fine. just 2.4Ghz is way better then 5Ghz channel.

I have 50Mb/10Mb xfinity, 2.4Ghz channel can have around 45Mb/10Mb internet speed, 5Ghz channel stick around 20Mb/10Mb no matter how close to the router.
davidkennedy85
DD-WRT Novice


Joined: 10 Sep 2012
Posts: 18

PostPosted: Mon Sep 17, 2012 21:37    Post subject: Reply with quote
Flashing dd-wrt.v24-18946_NEWD-2_K2.6_mini-e1200v1.bin to Cisco Linksys E1200 V1 went without a hitch. However wi-fi speed is awful, especially on iPad. Wife is not happy about this. I tried disabling the three settings related to DNSMasq on the main Setup page which seemed to help a little, but I really need DNSMasq so it's not really a good solution.
MongooseProXC
DD-WRT User


Joined: 24 May 2012
Posts: 80

PostPosted: Sat Sep 29, 2012 13:56    Post subject: Reply with quote
davidkennedy85 wrote:
Flashing dd-wrt.v24-18946_NEWD-2_K2.6_mini-e1200v1.bin to Cisco Linksys E1200 V1 went without a hitch. However wi-fi speed is awful, especially on iPad. Wife is not happy about this. I tried disabling the three settings related to DNSMasq on the main Setup page which seemed to help a little, but I really need DNSMasq so it's not really a good solution.


Try adding the following to the Administration>Commands section, save to startup, and reboot.
This will set the transmit power to the driver default and force enable interference mitigation.

wl txpwr1 -1
wl interference 2
Fractal
DD-WRT Guru


Joined: 19 Apr 2010
Posts: 1157

PostPosted: Sat Sep 29, 2012 15:27    Post subject: Reply with quote
try above mentioned settings... also I have new builds available on barryware's ftp that address alot of issues since that revision... I am testing 20012 right now if that goes well it will be up there.

-Fractal
spanman
DD-WRT User


Joined: 27 Sep 2008
Posts: 444
Location: Port Of Spain

PostPosted: Sun Jun 09, 2013 5:03    Post subject: Milkfish Reply with quote
I am getting problems with milkfish on DD-WRT v24-sp2 (04/07/12) big - build 18946M NEWD Eko WRT54G-TM. I was on 15230 mega before and milkfish was working perfectly.
I am only using local subscribers. I added my local subscribers in the gui but i still cannot register a client on lan or wan.
As i said before this worked perfectly on 15230 mega build from eko.

However when I insert the commands below via telnet I can register, but when the router reboots i cannot register again.


nvram set sip_domain=xxxx.homesip.net
nvram set milkfish_enabled=1
nvram set milkfish_password=xxxx
nvram set milkfish_dynsip=on
nvram set milkfish_username=xxxx
nvram set milkfish_fromdomain=xxxx.homesip.net
nvram set milkfish_fromswitch=on
nvram commit
reboot

milkfish_services sipdb adduser 1000 1000
milkfish_services sipdb adduser 1001 1001
milkfish_services phonebook
milkfish_services sipdb storenv
nvram commit
reboot

Is there any higher build with working Milkfish for WRT54G-TM? Or did something changed with milkfish from 15230? I just thought I should try a newer build but i may just revert back to 15230 mega.

Openvpn, wireless AP and my other settings works perfectly in DD-WRT v24-sp2 (04/07/12) big - build 18946M NEWD Eko though.

_________________
Buffalo WZR-600DHP - 23838
TP Link WDR3600 - 21676
Linksys WRT54G-TM - 12548 (NEWD Eko Mega)
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8, 9 Display posts from previous:    Page 9 of 9
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum