Posted: Wed Oct 05, 2022 5:20 Post subject: New Build - 10/05/2022 - r50357
Welcome to Atheros r50357 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Misc: stracetcpdumpwireshark.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Netgear Nighthawk X10 R9000
Firmware Version DD-WRT v3.0-r50357 std (10/05/22)
Kernel Version Linux 4.9.330 #651 SMP Tue Oct 4 13:04:30 +07 2022 armv7l
Current Time Wed, 05 Oct 2022 00:28:15
Uptime 1 min
GUI over 50313
Reset: no
Issues: upgraded fine
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Wed Oct 05, 2022 7:21 Post subject:
Router Model Netgear R7800
Firmware Version DD-WRT v3.0-r50357 std (10/05/22)
Kernel Version Linux 4.9.330 #1253 SMP Wed Oct 5 01:03:16 +07 2022 armv7l
update: CLI r50313 > r50357
reset: NO
mode: Gateway
status: Operational 12h+
errors: Nothing new, yet...Thanks BS & Team !
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r50357 std (10/05/22)
Kernel Version Linux 3.18.140-d6 #154673 Wed Oct 5 06:09:13 +07 2022 mips
update: GUI r50313 > r50357
reset: NO
mode: Gateway
status: Operational 12h+
errors: Nothing new, yet...Thanks BS & Team ! _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Last edited by Alozaros on Sat Oct 08, 2022 6:12; edited 1 time in total
Joined: 05 Oct 2008 Posts: 667 Location: Helsinki, Finland / nr. Alkmaar, Netherlands
Posted: Wed Oct 05, 2022 13:41 Post subject:
Router/Version: R7800
File/Kernel: Linux 4.9.330 #1253 SMP Wed Oct 5 01:03:16 +07 2022 armv7l
Previous/Reset: 50313/nvram reset recently, a few versions back
Mode/Status: LAN & WLAN router connected to cable modem
Issues/Errors: none, except a very long standing issue that I haven't seen mentioned, viz. while I am browsing the router's GUI, a dialog pops up asking permission to store a password for an account named 8000, or some such. Bogus and I decline every time. It's annoying.
The GUI feels distinctly more snappy now than in recent previous version!! It's been rather tardy for many versions, both before and after the great reset.
QoS WAN HSFC Cake set at 18000/1300. Getting some 13000/1000, but at B ratings per dslreports.com/speedtest. If I go lower still, I get A ratings at lower speeds. I am behind a 'corporate' firewall. Without QoS I've seen the corporate 'WAN' peak at over 40 Mb/s, just the very beginning of the test, dropping steeply rapidly.
Virtual LAN network on one port. bridged with a VAP.
Two more VAP's, one for IoT (smart switches), the other for guests. Not that there are many around, but it's a hobby, right.
Firewall rules to isolate the IoT stuff.
Reserved IP file on a thumbdrive JFFS.
Updated through easyddup.
Local DNS server PiHole/Unbound on a Raspberry Pi Zero with small UPS board.
CPU frequency scaling set in startup script.
Cleanup thumbdrive partitions with e2fsck in usb script.
No IPv6.
Last edited by ArjenR49 on Wed Oct 05, 2022 21:06; edited 1 time in total
Joined: 12 Dec 2007 Posts: 783 Location: Pittsburgh, PA USA
Posted: Thu Oct 06, 2022 0:08 Post subject:
AsX wrote:
In WireGuard, how the new Tunnel Obfuscation is supposed to work? What is the Key and what can it be set to?
And do you need to update the client config? _________________ __________________________
Netgear R7800
DD-WRT v3.0 STD
Linksys WRT1900AC
DD-WRT v3.0 STD
_________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
Joined: 18 Mar 2014 Posts: 12923 Location: Netherlands
Posted: Thu Oct 06, 2022 5:46 Post subject:
About WireGuard obfuscation, we are still working on it and maybe the definitive implementation will change, so it is not yet in the manual.
But it works and is intended to obfuscate WG traffic so it should be able to pass a blocking firewall.
On the server side enable it and set the password in the tunnel section.
Note the whole tunnel is obfuscated.
On the client (the side which has an endpoint enabled in the peer)
Do the same but it should be set in the Peer section just under the endpoint.
Use the same password.
It will lower throughput.
I have also made an implementation were you set the obfuscation per peer on the server side but in that case you also have to set the Remote listen port, advantage is that a server can have clients with and without obfuscation.