hiroyuki DD-WRT Novice
Joined: 14 May 2012 Posts: 5
|
Posted: Wed May 16, 2012 3:58 Post subject: No wireless tab problem on nano station loco 5 |
|
Hi
I flashed r18777 & r16214 (LC5.dd-wrt.bin) but wireless tab was missing.
Dose anyone succeed on same device with other built?
Here is dmesg
root@DD-WRT:~# dmesg
<5>[ 0.000000] Linux version 3.2.12-rc1-svn18774 (root@dd-wrt) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #764 Mon Mar 19 09:13:35 CET 2012
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU revision is: 0001800a (MIPS 4Kc)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 01000000 @ 00000000 (usable)
<4>[ 0.000000] Zone PFN ranges:
<4>[ 0.000000] Normal 0x00000000 -> 0x00001000
<4>[ 0.000000] Movable zone start PFN for each node
<4>[ 0.000000] early_node_map[1] active PFN ranges
<4>[ 0.000000] 0: 0x00000000 -> 0x00001000
<7>[ 0.000000] On node 0 totalpages: 4096
<7>[ 0.000000] free_area_init_node: node 0, pgdat 802c5880, node_mem_map 8032e000
<7>[ 0.000000] Normal zone: 32 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 4064 pages, LIFO batch:0
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock1 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 64 (order: -4, 256 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
<4>[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
<4>[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes
<6>[ 0.000000] Memory: 12944k/16384k available (2200k kernel code, 3440k reserved, 379k data, 156k init, 0k highmem)
<6>[ 0.000000] NR_IRQS:128
<6>[ 0.000000] console [ttyS0] enabled, bootconsole disabled
<6>[ 0.010000] Calibrating delay loop... 179.60 BogoMIPS (lpj=898048)
<6>[ 0.090000] pid_max: default: 32768 minimum: 301
<6>[ 0.090000] Mount-cache hash table entries: 512
<6>[ 0.100000] NET: Registered protocol family 16
<6>[ 0.200000] bio: create slab <bio-0> at 0
<6>[ 0.220000] Switching to clocksource MIPS
<6>[ 0.240000] NET: Registered protocol family 2
<6>[ 0.240000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.250000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
<6>[ 0.260000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
<6>[ 0.270000] TCP: Hash tables configured (established 512 bind 512)
<6>[ 0.270000] TCP reno registered
<6>[ 0.280000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.280000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.290000] NET: Registered protocol family 1
<4>[ 0.300000] scanning for board data at BE7FF000 (FFFFFFFF)
<4>[ 0.300000] scanning for board data at BE7FE000 (A017168C)
<4>[ 0.310000] scanning for board data at BE7FD000 (FFFFFFFF)
<4>[ 0.310000] scanning for board data at BE7FC000 (35333131)
<4>[ 0.320000] found 1
<4>[ 0.320000] Found board config at 0xbe7fc000
<4>[ 0.320000] Radio config found at offset 0x2000(0x100) (be7fe000)
<5>[ 0.340000] gpio_proc: module loaded and /proc/gpio/ created
<6>[ 0.360000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.360000] msgmni has been set to 25
<6>[ 0.380000] io scheduler noop registered
<6>[ 0.380000] io scheduler deadline registered (default)
<6>[ 0.390000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.420000] serial8250: ttyS0 at MMIO 0xbc000003 (irq = 37) is a 16550A
<3>[ 0.430000] serial8250 serial8250.0: unable to register port at index 0 (IO3f8 MEM0 IRQ4): -28
<3>[ 0.440000] serial8250 serial8250.0: unable to register port at index 1 (IO2f8 MEM0 IRQ3): -28
<3>[ 0.440000] serial8250 serial8250.0: unable to register port at index 2 (IO3e8 MEM0 IRQ4): -28
<3>[ 0.450000] serial8250 serial8250.0: unable to register port at index 3 (IO2e8 MEM0 IRQ3): -28
<6>[ 0.470000] gpiodev: gpio device registered with major 254
<5>[ 0.480000] physmap platform flash device: 00800000 at 1e000000
<6>[ 0.490000] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0000a7
<7>[ 0.500000] physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
<6>[ 0.500000] Amd/Fujitsu Extended Query Table at 0x0040
<6>[ 0.510000] Amd/Fujitsu Extended Query version 1.1.
<4>[ 0.510000] physmap-flash.0: Swapping erase regions for top-boot CFI table.
<5>[ 0.520000] number of CFI chips: 1
<5>[ 0.520000] Searching for RedBoot partition table in physmap-flash.0 at offset 0x3d0000
<5>[ 0.550000] Searching for RedBoot partition table in physmap-flash.0 at offset 0x3e0000
<5>[ 0.580000] 8 RedBoot partitions found on MTD device physmap-flash.0
<5>[ 0.590000] Creating 8 MTD partitions on "physmap-flash.0":
<5>[ 0.590000] 0x000000000000-0x000000030000 : "RedBoot"
<5>[ 0.610000] 0x000000030000-0x0000003d0000 : "rootfs"
<5>[ 0.620000] 0x0000002f0000-0x0000003d0000 : "kernel"
<5>[ 0.640000] 0x0000003d0000-0x0000003e0000 : "nvram"
<5>[ 0.660000] 0x0000003e0000-0x0000003f0000 : "FIS directory"
<5>[ 0.670000] 0x0000003ef000-0x0000003f0000 : "RedBoot config"
<5>[ 0.690000] 0x0000003f0000-0x000000400000 : "board_config"
<5>[ 0.700000] 0x000000000000-0x0000003f0000 : "fullflash"
<6>[ 0.720000] ar531x: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0000a7
<6>[ 0.730000] Amd/Fujitsu Extended Query Table at 0x0040
<6>[ 0.740000] Amd/Fujitsu Extended Query version 1.1.
<4>[ 0.740000] ar531x: Swapping erase regions for top-boot CFI table.
<5>[ 0.750000] number of CFI chips: 1
<5>[ 0.760000] AR531x Flash device initialized: size 0x0 at 0x0 bankwidth 0x400000
<6>[ 0.800000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.800000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<4>[ 0.880000] eth0: Atheros AR231x: 00:27:22:87:00:4d, irq 4
<6>[ 0.950000] ar231x_eth_mii: probed
<6>[ 0.960000] eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=0:01)
<6>[ 0.970000] PPP generic driver version 2.4.2
<6>[ 0.980000] PPP BSD Compression module registered
<6>[ 0.980000] PPP Deflate Compression module registered
<6>[ 0.990000] PPP MPPE Compression module registered
<6>[ 1.000000] NET: Registered protocol family 24
<6>[ 1.000000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout= 0)
<6>[ 1.010000] u32 classifier
<6>[ 1.020000] input device check on
<6>[ 1.020000] Actions configured
<6>[ 1.020000] Netfilter messages via NETLINK v0.30.
<6>[ 1.030000] nf_conntrack version 0.5.0 (202 buckets, 808 max)
<4>[ 1.040000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 1.040000] nf_nat_rtsp v0.6.21 loading
<6>[ 1.050000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 1.050000] IPP2P v0.8.2 loading
<6>[ 1.060000] TCP westwood registered
<6>[ 1.060000] TCP hybla registered
<6>[ 1.060000] TCP vegas registered
<6>[ 1.070000] NET: Registered protocol family 17
<6>[ 1.070000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 1.080000] searching for nvram
<6>[ 1.080000] nvram size = 0
<6>[ 1.130000] VFS: Mounted root (squashfs filesystem) readonly on device 31:1.
<6>[ 1.140000] Freeing unused kernel memory: 156k freed
<6>[ 1.970000] eth0: Configuring MAC for full duplex
<4>[ 11.810000] ath_hal: module license 'Proprietary' taints kernel.
<4>[ 11.820000] Disabling lock debugging due to kernel taint
<6>[ 11.830000] ath_hal: 2009-05-08 (AR5212, AR5312, RF5111, RF5112, XR)
<6>[ 12.980000] ath_ahb: svn r1404
<6>[ 12.990000] wlan: svn r1404
<6>[ 12.990000] wlan: mac acl policy registered
<6>[ 12.990000] ath_rate_sample: 1.2 (svn r1404)
<6>[ 13.000000] ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (svn r1404)
<6>[ 13.010000] ath_rate_minstrel: look around rate set to 10%
<6>[ 13.010000] ath_rate_minstrel: EWMA rolloff level set to 75%
<6>[ 13.020000] ath_rate_minstrel: max segment size in the mrr set to 6000 us
<4>[ 13.040000] Atheros HAL provided by OpenWrt, DD-WRT and MakSat Technologies
<3>[ 13.050000] MadWifi: ath_getchannels: Unable to collect channel list from HAL; regdomain likely 42 country code 0
<4>[ 13.060000] wifi%d: ath_attach failed: -22
<6>[ 17.400000] device eth0 entered promiscuous mode
<6>[ 17.440000] br0: port 1(eth0) entering forwarding state
<6>[ 17.440000] br0: port 1(eth0) entering forwarding state
<6>[ 19.440000] br0: port 1(eth0) entering forwarding state
<6>[ 291.820000] br0: port 1(eth0) entering forwarding state
<6>[ 292.110000] device eth0 left promiscuous mode
<6>[ 292.120000] br0: port 1(eth0) entering disabled state
<6>[ 296.870000] device eth0 entered promiscuous mode
<6>[ 296.910000] br0: port 1(eth0) entering forwarding state
<6>[ 296.910000] br0: port 1(eth0) entering forwarding state
<6>[ 298.910000] br0: port 1(eth0) entering forwarding state
If someone can help me, I am appreciated. |
|