BasCom
DD-WRT Guru
Joined: 29 Jul 2009
Posts: 1378
Location: Germany
|
 Posted: Thu Jun 21, 2012 9:32 Post subject: tl-wr1043nd automount usb on boot issue |
 |
hello all. have this problem:
tl-wr1043nd does not mount the connected usb stick druring boot.
dmesg shows
| Code: |
<6>[ 5.850000] usbcore: registered new interface driver usbfs
<6>[ 5.860000] usbcore: registered new interface driver hub
<6>[ 5.860000] usbcore: registered new device driver usb
<6>[ 5.960000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 6.020000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 6.030000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<6>[ 6.070000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 6.090000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 6.090000] hub 1-0:1.0: USB hub found
<6>[ 6.100000] hub 1-0:1.0: 1 port detected
<5>[ 6.390000] SCSI subsystem initialized
<6>[ 6.450000] usb 1-1: new high-speed USB device number 2 using ar71xx-ehci
<6>[ 6.730000] Initializing USB Mass Storage driver...
<6>[ 6.730000] usbcore: registered new interface driver usb-storage
<6>[ 6.740000] USB Mass Storage support registered.
<6>[ 6.780000] scsi0 : usb-storage 1-1:1.0
<6>[ 7.790000] scsi scan: INQUIRY result too short (5), using 36
<5>[ 7.790000] scsi 0:0:0:0: Direct-Access PQ: 1 ANSI: 0
<6>[ 8.550000] device br0 entered promiscuous mode
<6>[ 8.620000] device vlan1 entered promiscuous mode
<6>[ 8.620000] device eth0 entered promiscuous mode
<6>[ 8.630000] br0: port 1(vlan1) entering forwarding state
<6>[ 8.630000] br0: port 1(vlan1) entering forwarding state
<6>[ 8.640000] device br0 left promiscuous mode
<6>[ 8.650000] device br0 entered promiscuous mode
<6>[ 8.660000] device br0 left promiscuous mode
<6>[ 8.670000] device br0 entered promiscuous mode
<6>[ 8.730000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 8.760000] cfg80211: World regulatory domain updated:
<6>[ 8.760000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 8.770000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.780000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.790000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.800000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.800000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.810000] cfg80211: Calling CRDA for country: DE
<6>[ 8.830000] cfg80211: Regulatory domain changed to country: DE
<6>[ 8.840000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 8.840000] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
<6>[ 8.850000] cfg80211: (5150000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
<6>[ 8.860000] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
<6>[ 10.630000] br0: port 1(vlan1) entering forwarding state
<6>[ 13.320000] device ath0 entered promiscuous mode
<6>[ 13.320000] br0: port 2(ath0) entering forwarding state
<6>[ 13.330000] br0: port 2(ath0) entering forwarding state
<6>[ 15.330000] br0: port 2(ath0) entering forwarding state
<6>[ 17.440000] warning: `proftpd' uses 32-bit capabilities (legacy support in use)
|
i always have to plug out/in the usb-stick getting it accessable.
the dmesg shows:
| Code: |
<6>[ 358.360000] usb 1-1: USB disconnect, device number 2
<6>[ 360.540000] usb 1-1: new high-speed USB device number 3 using ar71xx-ehci
<6>[ 360.700000] scsi1 : usb-storage 1-1:1.0
<5>[ 361.710000] scsi 1:0:0:0: Direct-Access Mass Storage Device PQ: 0 ANSI: 0 CCS
<5>[ 361.720000] sd 1:0:0:0: [sda] 32112639 512-byte logical blocks: (16.4 GB/15.3 GiB)
<5>[ 361.730000] sd 1:0:0:0: [sda] Write Protect is off
<7>[ 361.730000] sd 1:0:0:0: [sda] Mode Sense: 03 00 00 00
<3>[ 361.730000] sd 1:0:0:0: [sda] No Caching mode page present
<3>[ 361.740000] sd 1:0:0:0: [sda] Assuming drive cache: write through
<3>[ 361.750000] sd 1:0:0:0: [sda] No Caching mode page present
<3>[ 361.760000] sd 1:0:0:0: [sda] Assuming drive cache: write through
<6>[ 361.760000] sda:
<3>[ 361.770000] sd 1:0:0:0: [sda] No Caching mode page present
<3>[ 361.780000] sd 1:0:0:0: [sda] Assuming drive cache: write through
<5>[ 361.780000] sd 1:0:0:0: [sda] Attached SCSI removable disk
<4>[ 362.880000] FAT-fs (sda): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
|
any hints for me? thanks all.
_________________
RT-N66U @ Build 25697M K3.10.63
TL-WR842ND v1 @ BS-build 23919 WDS AP
TL-WR841ND @ BS-build 23919 WDS Client
TL-WR841ND @ BS-build 23919 Client Bridge ( Routed ) |
|
