Posted: Sun Nov 09, 2014 15:30 Post subject: Re: I just buy a RT-AC66U
No answers soon sad!!
necroraven wrote:
Hi guys i just buy a RT-AC66u , and I install dd-wrt version of 25179 for Asus RT-AC66U .
Do i need to do something else ?
Do i have to config something to get the best out of it?
Is this the best version of dd-wrt ?
There is some harding that i have to do (like disable telnet?)
Cheers! and thks for thi great community and support.
[/list]
Hope someone can help or point me in the right direction, I have kong ac installed and for some reason, unknown at this time, my router was in asus recovery when i came back from work today. Eventually reset it to dd-wrt stock with Kong AC, but now my 5ghz wireless is not sending or receiving anything. Ive setup everything same as was before but nothing at all for 5ghz.
Posted: Thu Nov 27, 2014 8:14 Post subject: Re: ac 66 dead
Feuerbard wrote:
have one dead after 6 month great working (dead after usual reboot)
power led fast blinking , restore mode working - tryed clear nvram from web cfi , tryed all official and alternative firmware - flashing ok then reboots and rapid fast power blink again
in console
Code:
CFE version 6.30.39.16 (r331229) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Jul 3 13:19:49 CST 2012 (defjovi@F13)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.39.16 (r331229)
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
Device eth0: hwaddr 30-85-xx-xx-xx-xx, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
Wait until reset button released...
restoration utility log
Code:
Reading :: TFTP Server.
- last blk -
Done. 10850304 bytes read
Download of 0xa59000 bytes completed
Write kernel and filesystem binary to FLASH
Programming...copysize=10850304, amtcopy=10850304
done. 10850304 bytes written
i can enter to cfe by ctrl-c
available commands
Code:
Available commands: show, nvram, reboot, flash, batch, go, boot, load, save, ping, arp, ifconfig, help
Code:
show devices Display information about the installed devices.
show clocks Show current values of the clocks.
nvram NVRAM utility.
reboot Reboot.
flash Update a flash memory device
batch Load a batch file into memory and execute it
go Verify and boot OS image.
boot Load an executable file into memory and execute it
load Load an executable file into memory without executing it
save Save a region of memory to a remote file via TFTP
ping Ping a remote IP host.
arp Display or modify the ARP Table
ifconfig Configure the Ethernet interface
help Obtain help for CFE commands
anyone help ???
what is it - dead spi flash or dead nand flash or something else??
I got the same error you had above:
Wait until reset button released...
My AC66u completely failed to boot, it started with a rapidly blinking power light.
I was able to TFTP a recovery image but after the first restart I would end up at the error again (using a USB TTL cable to get the console output)
After I loaded an ASUS FW I tried switching the WPS button to Wireless Toggle, from the console I could see the toggle on/off repeatedly..
So after fiddling with the button I decided to just simply desolder it. After that was complete and the button removed... it works perfectly now.
GUYS i have had it with the bugs in DD-WRT and the problems with my VPN I want to go back to STOCK. For this router can someone confirm if I can just reflash the stock image or do I have to do anything else? Please let me know. Thanks.
Change the .trx ending of the asus firmware to .bin and flash it through the upgrade page. _________________ I am far from a guru, I'm barely a novice.