dapperdan
DD-WRT Novice
Joined: 04 May 2011
Posts: 5
|
 Posted: Wed Aug 15, 2012 20:40 Post subject: |
 |
Eine FCC-ID hat der Router leider nicht, aber wahrscheinlich wird er wegen des Modems auch nicht in den USA vermarktet.
Da mein Model die gleiche Modelnummer (DGND3800B-100GRS) hat, nehme ich mal die Infos vom OpenWrt Wiki.
CPU: BCM6368B2, MIPS: 400MHz
Flash AM29LV320MT, 32MB
RAM: Samsung K4H511638J-LCCC (?), 128MB
WLAN Controller: BCM4350/51 (laut dmesg), BCM43222KFBG (Chip)
Bootloader output:
| Quote: | DGND3700 Boot Code V1.0.8
CFE version 1.0.37-104.4 for BCM96368 (32bit,SP,BE)
Build Date: Mon Feb 21 17:59:46 CST 2011 (finerain@moonlight)
Copyright (C) 2000-2009 Broadcom Corporation.
Parallel flash device: name AM29LV320MT, id 0x2201 size 32768KB
Total Flash size: 32768K with 256 sectors
ethsw: found bcm53115!
Chip ID: BCM6368B2, MIPS: 400MHz
Main Thread: TP0
Total Memory: 134217728 bytes (128MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-11) : 96368MVWG
Number of MAC Addresses (1-32) : 10
Base MAC Address : XX:XX:XX:XX:XX:XX
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0 |
Laut User hvandrie auf openwrt.org soll der Router die Firmware wohl auch vom Host laden können? (s.o. "Run from flash/host (f/h) : f")
dmesg output:
| Quote: | F1G08U0A 128MB
Found NAND: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0201 128MB @00000000
brcmnand_probe: CS0: dev_id=ecf10095
1. Found NAND chip on Chip Select 0, chipSize=128MB, usable size=128MB, base=0x00000000
brcmnand_scan: B4 nand_select = 40000002
brcmnand_scan: After nand_select = 40000002
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 2.1 NAND flash size 128MB @16000000
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table found at page 65472, version 0xFF
Bad block table found at page 65408, version 0xFF
numchips=1, size=8000000
Creating 1 MTD partitions on "bcm63xx-nand.0":
0x00000000-0x08000000 : "storage"
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
===>brcm_board_init: GPIO->GPIOBaseMode=0x3b000
===>brcm_board_init: GPIO->GPIOMode=0x1f0003
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Dec 29 2011 12:44:20
netem: version 1.2
u32 classifier
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Initializing MCPD Module
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 92k freed
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow Cache Char Driver v2.1 Nov 20 2009 22:08:08 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Nov 20 2009 22:08:06
Broadcom Packet CMF (Experimental) Char Driver v0.1 Nov 20 2009 22:08:03 Registered<232>
Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Nov 20 2009 22:08:02 Loaded
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6368B2 Ethernet Network Device v0.1 Dec 29 2011 12:44:13
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
Config Switch Through SPI Slave Select 1
ethsw: found bcm53115!
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
Broadcom Packet CMF (Experimental) SWC RESET.
Broadcom Packet CMF (Experimental) SWC INITIALIZED.
KLOB extended to 5 pools
KLOB extended to 6 pools
KLOB extended to 7 pools
KLOB extended to 8 pools
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Nov 20 2009 22:08:03 Registered
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Nov 20 2009 22:08:03 Registered
Broadcom Packet CMF (Experimental) ENABLED.
eth0: MAC Address: XX:XX:XX:XX:XX:XX
eth1: MAC Address: XX:XX:XX:XX:XX:XX
eth2: MAC Address: XX:XX:XX:XX:XX:XX
eth3: MAC Address: XX:XX:XX:XX:XX:XX
eth4: MAC Address: XX:XX:XX:XX:XX:XX
eth0 Link DOWN.
eth1 Link DOWN.
eth2 Link DOWN.
eth3 Link DOWN.
eth4 Link DOWN.
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
wl0: Broadcom BCM4351 802.11 Wireless Controller 5.10.120.0.cpe4.404.8
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:02.0 to 64
wl1: Broadcom BCM4350 802.11 Wireless Controller 5.10.120.0.cpe4.404.8
dgasp: kerSysRegisterDyingGaspHandler: wl1 registered
p8021ag: p8021ag_init entry
Broadcom Packet Flow Cache learning via BLOG disabled.
klips_info:ipsec_init: KLIPS startup, Openswan KLIPS IPsec stack version: 2.4.9
NET: Registered protocol family 15
klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=251)
klips_info:ipsec_alg_init: calling ipsec_alg_static_init()
ipsec_3des_init(alg_type=15 alg_id=3 name=3des): ret=0
<6>KLIPS cryptoapi interface: alg_type=15 alg_id=12 name=cbc(aes) keyminbits=128 keymaxbits=256, found(0)
KLIPS: lookup for ciphername=cbc(twofish): not found
KLIPS: lookup for ciphername=cbc(serpent): not found
KLIPS: lookup for ciphername=cbc(cast5): not found
KLIPS: lookup for ciphername=cbc(blowfish): not found
<6>KLIPS cryptoapi interface: alg_type=15 alg_id=3 name=cbc(des3_ede) keyminbits=192 keymaxbits=192, found(0)
<6>KLIPS cryptoapi interface: alg_type=15 alg_id=2 name=cbc(des) keyminbits=64 keymaxbits=64, found(0)
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
device eth4 entered promiscuous mode
device wl0 entered promiscuous mode
device wl1 entered promiscuous mode
bcmxtmrt: MAC address: xx xx xx xx xx xx
atm0.6: Setting MAC address to xx xx xx xx xx xx.
VLAN (atm0.6): Underlying device (atm0) has same MAC, not checking promiscious mode.
atm0.6: add 01:00:5e:00:00:01 mcast address to master interface
atm0.8: Setting MAC address to xx xx xx xx xx xx.
device atm0 entered promiscuous mode
VLAN (atm0. : Setting underlying device (atm0) to promiscious mode.
atm0.8: add 01:00:5e:00:00:01 mcast address to master interface
BcmAdsl_Initialize=0xC010EA10, g_pFnNotifyCallback=0xC0142FD4
Clocks for QPROC and AFE are being aligned with step through ...
AFE is aligned, i = 050, PhaseValue = -150, PhaseCntl = 0x7FCF0000
QPROC is aligned, i = 051, PhaseValue = -050, PhaseCntl = 0x7FCF3FCD
Clocks for QPROC and AFE are aligned with syn_status AFE = 0x78, QPROC = 0x70
AFE phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f
QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f
pSdramPHY=0xA7FFFFF8, 0xF7FF9460 0xFFFF38E9
*** XfaceOffset: 0x5FF90 => 0x5FF90 ***
*** PhySdramSize got adjusted: 0xB9D78 => 0xE77A8 ***
AdslCoreSharedMemInit: shareMemAvailable=100400
AdslCoreHwReset: pLocSbSta=86d48000 bkupThreshold=3072
AdslCoreHwReset: AdslOemDataAddr = 0xA7FAF3F4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
IOCTL_AG_REGION_SET: English
device wl0.1 entered promiscuous mode
device wl0.2 entered promiscuous mode
device wl0.3 entered promiscuous mode
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
device wl1.1 entered promiscuous mode
device wl1.2 entered promiscuous mode
device wl1.3 entered promiscuous mode
br0: port 5(wl1) entering learning state
br0: topology change detected, propagating
br0: port 5(wl1) entering forwarding state |
Einen JTAG-Adapter hab ich leider nicht, mit cfe.bin und nvram.bin kann ich also leider nicht dienen. Catalyst vielleicht? |
|
