SOLVED: Bricked ASUS RT-N66U: JTAG?

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2  Next
Author Message
zyxeu
DD-WRT Novice


Joined: 29 Oct 2012
Posts: 13

PostPosted: Mon Oct 29, 2012 18:05    Post subject: SOLVED: Bricked ASUS RT-N66U: JTAG? Reply with quote

1. Would an unbuffered JTAG be enough to unbrick the router? Or should it be better a buffered JTAG?
2. Is the RT-N66U(Broadcom BCM4706/BCM4331) already supported by tjtag for unbricking?


Some background:
- I have an unreachable(no ping/tftp) ASUS RT-N66U which is in a “locked in” recovery mode (power led flashing slowly).
- 64 kB CFE has been working and after a failed flash and a "WPS" hard reset it seems to be corrupted now and eth0 is not initialized: no ethernet access to the router.
- I have a backup of my original 32kB CFE.

I have found that LOM wrote that:
Quote:
“It has now been confirmed (by using TIAO buffered adapter and tjtag) that the RT-N66U has an active jtag port with standard pinout…”
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=159756&postdays=0&postorder=asc&start=45

Last edited by zyxeu on Sun Nov 04, 2012 4:29; edited 4 times in total
Sponsor
zyxeu
DD-WRT Novice


Joined: 29 Oct 2012
Posts: 13

PostPosted: Wed Oct 31, 2012 1:40    Post subject: RT-N66U 64kB CFE corrupt after clear via WPS button Reply with quote
Is there a way to init eth0 via CFE's serial connection?

I connected the serial cable and did a "CFE> nvram erase" + "reboot".

Unfortunately this did not bring back the unreachable router.

As you can see in the following CFE boot log below there are two issues:
- "Boot program checksum is invalid"
- There is no eth0 initialization

This last bullet explains why the router is not reachable via eth0 and IP 192.168.1.1.

Code:

�Decompressing...done                                                                           
tmp_ret= 0                                                                                       
                                                                                                 

CFE version 5.100.127 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 五  9月 14 17:47:35 CST 2012 (boyau@localhost)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.127
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes

CFE mem:    0x80700000 - 0x80839350 (1282896)
Data:       0x80733120 - 0x807363E0 (12992)
BSS:        0x807363E0 - 0x80737350 (3952)
Heap:       0x80737350 - 0x80837350 (1048576)
Stack:      0x80837350 - 0x80839350 (8192)
Text:       0x80700000 - 0x80733118 (209176)

Device eth0:  hwaddr 20-CF-30-B7-00-08, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Null Rescue Flag.
Boot program checksum is invalid
Hello!! Enter Rescue Mode: (Check error)

Reading :: TFTP Server.
Failed.: Timeout occured
Reading :: TFTP Server.
Failed.: Timeout occured
Reading :: TFTP Server.
Failed.: Interrupted
CFE> nvram show
pci/2/1/leddc=0xFFFF
pci/1/1/pa2gw1a0=0x1AAD
pci/1/1/pa2gw1a1=0x1C2D
pci/1/1/pa2gw1a2=0x1971
pci/2/1/txchain=7
boardrev=0x1100
pci/2/1/phycal_tempdelta=0
pci/2/1/elna5g=2
pci/2/1/maxp5gla0=0x40
pci/2/1/maxp5gla1=0x40
pci/2/1/maxp5gla2=0x40
et0macaddr=20:CF:30:B7:00:08
boot_wait=on
watchdog=3000
pci/1/1/ledbh12=7
et0mdcport=0
pci/2/1/maxp5gha0=0x5E
pci/2/1/maxp5gha1=0x5E
pci/2/1/pa5gw0a0=0xFEE1
pci/2/1/maxp5gha2=0x5E
pci/2/1/pa5gw0a1=0xFEAC
pci/2/1/pa5gw0a2=0xFE9B
pmon_ver=CFE 5.100.127
pci/2/1/mcsbw20ul5gmpo=0x75311111
vlan2ports=0
pci/2/1/ccode=0
pci/2/1/extpagain5g=3
pci/2/1/boardflags=0x90000200
pci/2/1/pa5glw2a0=0xFA8E
pci/2/1/pa5glw2a1=0xFABC
pci/2/1/pa5glw2a2=0xFABC
pci/2/1/triso5g=3
pci/2/1/tempoffset=0
pci/2/1/mcsbw205gmpo=0x75311111
pci/1/1/legofdmbw202gpo=0x55555555
pci/1/1/ag0=0
pci/1/1/ag1=0
pci/1/1/ag2=0
gpio4=wps_button
pci/1/1/legofdmbw20ul2gpo=0x55555555
gpio7=robo_reset
pci/2/1/devid=0x4333
sromrev=8
pci/2/1/aa5g=7
boardtype=0xF5B2
pci/1/1/rxchain=7
lan_netmask=255.255.255.0
pci/1/1/cckbw202gpo=0x3333
pci/2/1/pa5ghw2a0=0XFAE4
pci/2/1/pa5ghw2a1=0XFAAE
pci/2/1/pa5ghw2a2=0XFB11
pci/1/1/mcsbw20ul2gpo=0xFC955555
pci/1/1/pa2gw0a0=0xFE74
pci/1/1/pa2gw0a1=0xFE8F
pci/1/1/pa2gw0a2=0xFE7F
pci/1/1/parefldovoltage=35
pci/1/1/boardflags=0x80001200
pci/2/1/macaddr=20:CF:30:B7:00:0C
vlan2hwname=et0
pci/1/1/tempoffset=0
odmpid=ASUS
xtalfreq=25000
pci/1/1/boardvendor=0x14E4
pci/2/1/mcsbw20ul5glpo=0x00000000
boardflags2=0x00000000
pci/2/1/pa5glw1a0=0x1637
pci/2/1/pa5glw1a1=0x1591
pci/2/1/pa5glw1a2=0x1591
pci/2/1/mcsbw205glpo=0x00000000
pci/1/1/triso2g=3
pci/1/1/sromrev=9
wait_time=3
pci/1/1/extpagain2g=3
pci/2/1/mcsbw20ul5ghpo=0x75311111
pci/2/1/legofdmbw205gmpo=0x75311111
pci/1/1/venid=0x14E4
pci/2/1/temps_period=5
pci/2/1/ledbh12=7
pci/2/1/mcsbw205ghpo=0x75311111
secret_code=19178752
pci/1/1/maxp2ga0=0x64
pci/1/1/maxp2ga1=0x64
pci/1/1/maxp2ga2=0x64
pci/2/1/pa5ghw1a0=0X158D
pci/2/1/pa5ghw1a1=0X1543
pci/2/1/pa5ghw1a2=0X1504
pci/2/1/parefldovoltage=60
pci/1/1/boardflags2=0x00100000
pci/1/1/tssipos2g=1
pci/2/1/pa5gw2a0=0xFAF7
pci/2/1/pa5gw2a1=0xFA82
pci/2/1/mcsbw405gmpo=0x75311111
pci/1/1/ledbh0=2
pci/2/1/pa5gw2a2=0xFAAC
pci/1/1/ledbh1=5
pci/1/1/ledbh2=4
pci/1/1/ledbh3=11
pci/2/1/ledbh0=2
pci/1/1/mcs32po=0x9999
pci/2/1/ledbh1=5
clkfreq=600,300,150
lan_ipaddr=192.168.1.1
pci/2/1/legofdmbw20ul5gmpo=0x75311111
pci/2/1/ledbh2=4
vlan1hwname=et0
pci/1/1/legofdm40duppo=0x4444
pci/2/1/rxchain=7
pci/2/1/ledbh3=11
pci/2/1/pdetrange5g=0
sdram_config=0x0000
pci/1/1/antswctl2g=0
vlan1ports=1
pci/2/1/pa5glw0a0=0xFE87
pci/2/1/maxp5ga0=0x5E
pci/2/1/legofdm40duppo=0x2222
pci/2/1/pa5glw0a1=0xFE9A
pci/2/1/maxp5ga1=0x5E
pci/2/1/pa5glw0a2=0xFE9A
pci/2/1/maxp5ga2=0x5E
pci/1/1/txchain=7
pci/1/1/elna2g=2
pci/1/1/aa2g=7
pci/1/1/antswitch=0
pci/2/1/legofdmbw205glpo=0x00000000
pci/2/1/venid=0x14E4
boardflags=0x00000110
sdram_refresh=0x0000
wandevs=et0
sdram_ncdl=0x00000000
pci/1/1/temps_hysteresis=5
pci/2/1/boardvendor=0x14E4
pci/2/1/legofdmbw205ghpo=0x75311111
pci/1/1/temps_period=5
pci/2/1/antswitch=0
pci/1/1/cckbw20ul2gpo=0x3333
pci/1/1/leddc=0xFFFF
pci/1/1/pa2gw2a0=0xF980
pci/2/1/tempthresh=120
pci/1/1/pa2gw2a1=0xF924
pci/1/1/pa2gw2a2=0xF9C8
pci/1/1/phycal_tempdelta=0
pci/2/1/pa5ghw0a0=0XFEDC
pci/2/1/sromrev=9
pci/2/1/pa5ghw0a1=0XFEB0
pci/2/1/pa5ghw0a2=0XFEDD
et0phyaddr=30
bl_version=1.0.1.3
pci/2/1/antswctl5g=0
landevs=vlan1
pci/2/1/pa5gw1a0=0x1663
pci/2/1/pa5gw1a1=0x1676
pci/2/1/mcsbw405glpo=0x00000000
pci/2/1/pa5gw1a2=0x15FA
pci/1/1/ccode=0
pci/2/1/legofdmbw20ul5glpo=0x00000000
pci/2/1/ag0=0
pci/2/1/ag1=0
pci/2/1/ag2=0
sdram_init=0x0000
pci/2/1/mcsbw405ghpo=0x75311111
pci/2/1/boardflags2=0x00200000
pci/2/1/legofdmbw20ul5ghpo=0x75311111
regulation_domain=US
pci/1/1/pdetrange2g=0
pci/1/1/regrev=39
regulation_domain_5G=Q2
pci/1/1/devid=0x4332
pci/2/1/regrev=2
pci/1/1/tempthresh=120
pci/1/1/macaddr=20:CF:30:B7:00:08
pci/1/1/mcsbw402gpo=0xFFFF9999
pci/2/1/mcs32po=0x2222
pci/2/1/temps_hysteresis=5
boardnum=00
pci/2/1/tssipos5g=1
pci/1/1/mcsbw202gpo=0xFC955555
size: 4024 bytes (61512 left)
*** command status = 0
CFE>
[/code]
barryware
DD-WRT Guru


Joined: 26 Jan 2008
Posts: 12846
Location: Behind The Reset Button

PostPosted: Wed Oct 31, 2012 13:38    Post subject: Reply with quote
The lan is being initialized:

Device eth0: hwaddr 20-CF-30-B7-00-08, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set


Stop the boot as you already have.. Then force the flash of STOCK firmware for your device. Get your tftp utility ready to go.

Remember to have a static ip set on your computer.

Then at the cfe prompt:

cfe> flash -ctheader:flash1.trx [enter]

launch the tftp utility and the firmware will flash.

It has been a while.. you may need to use -noheader instead of -ctheader.. I don't remember. If one ot the other is not the correct, you will get an error.. then just start over.

Once flashed and you are back at the cfe prompt, erase nvram again, then power cycle the router.

_________________
[Moderator Deleted] Shocked
zyxeu
DD-WRT Novice


Joined: 29 Oct 2012
Posts: 13

PostPosted: Wed Oct 31, 2012 23:53    Post subject: Reply with quote
barryware wrote:
The lan is being initialized:

Device eth0: hwaddr 20-CF-30-B7-00-08, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set


Stop the boot as you already have.. Then force the flash of STOCK firmware for your device. Get your tftp utility ready to go.

Remember to have a static ip set on your computer.

Then at the cfe prompt:

cfe> flash -ctheader:flash1.trx [enter]

launch the tftp utility and the firmware will flash.

It has been a while.. you may need to use -noheader instead of -ctheader.. I don't remember. If one ot the other is not the correct, you will get an error.. then just start over.

Once flashed and you are back at the cfe prompt, erase nvram again, then power cycle the router.


Thank you very much for your answer barryware.

Unfortunately it does not work:
Code:
CFE> flash -noheader : flash1.trx
Reading :: TFTP Server.
Failed.: Timeout occured
*** command status = -21


I cannot ping neither the router from PC nor the PC from the router.
If I put the router eth0 in loopback mode then I can ping itself.

tftp under linux is using "rexmt 1" and "timeout 600" and still in no intent did the "flash -noheader : flash1.trx" even remotely react.

To me it looks like as if the internal side of eth0 is not being routed to the exterior connectors.

So definitively it looks like eth0 is not completely initialized.

I even tried to add the arp entry for the PC in the router and vice versa in the PC.

If I run "go" then I get:
Code:
CFE> go
Null Rescue Flag.
Boot program checksum is invalid
Hello!! Enter Rescue Mode: (Check error)

So I suspect that only the "OS" flash went wrong and now the router is unreachable via eth0.

A good CFE boot looks like this:

Quote:
Device eth0: hwaddr 20-CF-30-B6-C7-B0, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
Loader:raw Filesys:tftp Dev:eth0 File:: Optionsnull)
Loading: TFTP Server.
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: .. 5100 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000

Linux version 2.6.22.19 (root@asus) (gcc version 4.2.4) #304 PREEMPT Wed Sep 21 19:18:57 CST 2011
CPU revision is: 00019749
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
memory: 08000000 @ 87fff000 (usable)
Zone PFN ranges:
Normal 0 -> 131072
HighMem 131072 -> 589823
early_node_map[2] active PFN ranges
0: 0 -> 32767
0: 557055 -> 589823
Built 1 zonelists. Total pages: 65535
Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
/quote]

The only rescue seems to be to have a working jtag support.

I will build a wiggler jtag, but still there seems to be no official support for BCM4706: Neither tjtag nor zjtag.

Any ideas?
barryware
DD-WRT Guru


Joined: 26 Jan 2008
Posts: 12846
Location: Behind The Reset Button

PostPosted: Thu Nov 01, 2012 0:17    Post subject: Reply with quote
zyxeu wrote:
barryware wrote:
The lan is being initialized:

Device eth0: hwaddr 20-CF-30-B7-00-08, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set


Stop the boot as you already have.. Then force the flash of STOCK firmware for your device. Get your tftp utility ready to go.

Remember to have a static ip set on your computer.

Then at the cfe prompt:

cfe> flash -ctheader:flash1.trx [enter]

launch the tftp utility and the firmware will flash.

It has been a while.. you may need to use -noheader instead of -ctheader.. I don't remember. If one ot the other is not the correct, you will get an error.. then just start over.

Once flashed and you are back at the cfe prompt, erase nvram again, then power cycle the router.


Thank you very much for your answer barryware.

Unfortunately it does not work:
Code:
CFE> flash -noheader : flash1.trx
Reading :: TFTP Server.
Failed.: Timeout occured
*** command status = -21


I cannot ping neither the router from PC nor the PC from the router.
If I put the router eth0 in loopback mode then I can ping itself.

tftp under linux is using "rexmt 1" and "timeout 600" and still in no intent did the "flash -noheader : flash1.trx" even remotely react.

To me it looks like as if the internal side of eth0 is not being routed to the exterior connectors.

So definitively it looks like eth0 is not completely initialized.

I even tried to add the arp entry for the PC in the router and vice versa in the PC.

If I run "go" then I get:
Code:
CFE> go
Null Rescue Flag.
Boot program checksum is invalid
Hello!! Enter Rescue Mode: (Check error)

So I suspect that only the "OS" flash went wrong and now the router is unreachable via eth0.

The only rescue seems to be to have a working jtag support.

I will build a wiggler jtag, but still there seems to be no official support for BCM4706: Neither tjtag nor zjtag.

Any ideas?

when I was helping with the port of this router.. I bricked it several times and recovered with serial every time. As I said, I do not remember exactly if it is -ctheader or -noheader.

static ip on your rig.. 192.168.1.10, mask 255.255.255.0..

get your tftp utility ready to launch..

issue your command and immediately launch the utility.

Your output says it is listening and timing out. Which could mean your firewall software or av software in messing with it, or you do not have your rig set right, or you are not connected from your nic on your rig to a LAN port on the router via cable.

_________________
[Moderator Deleted] Shocked
zyxeu
DD-WRT Novice


Joined: 29 Oct 2012
Posts: 13

PostPosted: Thu Nov 01, 2012 4:45    Post subject: Reply with quote
Quote:
when I was helping with the port of this router.. I bricked it several times and recovered with serial every time. As I said, I do not remember exactly if it is -ctheader or -noheader.

static ip on your rig.. 192.168.1.10, mask 255.255.255.0..

get your tftp utility ready to launch..

issue your command and immediately launch the utility.

Your output says it is listening and timing out. Which could mean your firewall software or av software in messing with it, or you do not have your rig set right, or you are not connected from your nic on your rig to a LAN port on the router via cable.


My setup is a cable connection on a Linux Mint PC with deactivated iptables via:
Code:
iptables -F
iptables -X
iptables -t nat -F
iptables -t nat -X
iptables -t mangle -F
iptables -t mangle -X
iptables -P INPUT ACCEPT
iptables -P FORWARD ACCEPT
iptables -P OUTPUT ACCEPT


The PC's IP is static just like you propose.

I have verified the connectivity with a RT-N13U router:
- PC(static IP) and router pingable from each end.

So it has to be a problem with the RT-N66U.

Apropos I have upgraded the CFE to rhyzov_al's 64kbit version. Maybe this one has an issue with the "emergency mode" and does not "open" the router.

That would be the only difference to your experience.
zyxeu
DD-WRT Novice


Joined: 29 Oct 2012
Posts: 13

PostPosted: Thu Nov 01, 2012 6:32    Post subject: unbricked RT-N66U!!! Reply with quote
Hi,

I got my RT-N66U back to life via the serial interface.

The trick was basically to write back some previously saved NVRAM settings in the CFE shell.


I simply added 4 newlines between each "nvram set ..." command and copy pasted several blocks of it.

The CFE shell seemed to get out of sync several times and did not get correctly the commands, but I continued to do the procedure several times for the fun of it.

Then I did a "nvram commit" followed by a "reboot".

After this basically the router was reachable again and I could tftp a firmware. I waited some extra 5 minutes after it said written in the CFE shell, did a power cycle with the reset button pressed to force the recovery mode, then I did a "nvram erase", "nvram commit" and a "reboot".

Result: Router back to life as previously.
mrkygeek
DD-WRT Novice


Joined: 04 Nov 2012
Posts: 1

PostPosted: Sun Nov 04, 2012 8:23    Post subject: Reply with quote
I am in the same situation after flashing CFE like 1.0.3 by ryzhov_al, and attempting to flash never wrt firmware.

@zyxeu: can you provide more details about the serial interface you used to connect to router?
zyxeu
DD-WRT Novice


Joined: 29 Oct 2012
Posts: 13

PostPosted: Sun Nov 04, 2012 14:32    Post subject: Reply with quote
mrkygeek wrote:
I am in the same situation after flashing CFE like 1.0.3 by ryzhov_al, and attempting to flash never wrt firmware.

@zyxeu: can you provide more details about the serial interface you used to connect to router?


Hi,

I used a USB to TTL 3.3V serial converter based on Prolific 2303 chipset like the following:
http://www.ebay.com/itm/USB-RS232-TTL-PL2303HX-Auto-Converter-Module-Converter-Adapter-5V-3-3V-Output-/170798767126

Works out of the box under Linux with newer kernels.

Guidelines can be found here:
http://www.dd-wrt.com/wiki/index.php/Serial_Recovery
http://www.dd-wrt.com/wiki/index.php/Tftp_flash
http://wiki.openwrt.org/doc/hardware/port.serial
profero
DD-WRT Novice


Joined: 07 Nov 2012
Posts: 1

PostPosted: Wed Nov 07, 2012 16:17    Post subject: Reply with quote
Zyxeu could you tell please what setting have you wrote back into nvram before committing. I have similar problem to your's. I just don't have NVRAM saved.
Router isn't visible over network for me either.
zyxeu
DD-WRT Novice


Joined: 29 Oct 2012
Posts: 13

PostPosted: Thu Nov 08, 2012 11:53    Post subject: Reply with quote
profero wrote:
Zyxeu could you tell please what setting have you wrote back into nvram before committing. I have similar problem to your's. I just don't have NVRAM saved.
Router isn't visible over network for me either.


Code:
nvram set wl_radius_port="1812"
nvram set wl_mac_deny=""
nvram set rrule0="0|1320|300|31|||word text ^begins-with.domain. .ends-with.net\$ ^www.exact-domain.net\$|0|example"
nvram set wl1_txant="3"
nvram set wl1_wme="on"
nvram set qos_reset="1"
nvram set https_crt=""
nvram set pptp_client_mru="1450"
nvram set wan_unit="0"
nvram set qos_irates="10,60,60,70,0,60,60,80,30,1"
nvram set log_in="0"
nvram set jffs2_on="0"
nvram set wl1_auth="0"
nvram set pci/2/1/leddc="0xFFFF"
nvram set ppp_custom=""
nvram set wl0_net_mode="mixed"
nvram set wl0_wmf_bss_enable="0"
nvram set led_override=""
nvram set sesx_led="0"
nvram set ms_port="0"
nvram set NC_Verbosity="2"
nvram set wl1_hwaddr="20:CF:30:B7:00:0C"
nvram set pci/1/1/pa2gw1a0="0x1AAD"
nvram set wl0_rifs_advert="auto"
nvram set wl0_mcast_regen_bss_enable="1"
nvram set dr_lan2_tx="0"
nvram set usb_3g="0"
nvram set smbd_autoshare="2"
nvram set t_features="0xC1"
nvram set pci/1/1/pa2gw1a1="0x1C2D"
nvram set ipv6_dns=""
nvram set wl0_frameburst="off"
nvram set wl_txstreams="0"
nvram set vpn_server1_nm="255.255.255.0"
nvram set wl1_net_mode="mixed"
nvram set pci/1/1/pa2gw1a2="0x1971"
nvram set wl_rxchain_pwrsave_pps="10"
nvram set smbd_enable="2"
nvram set pci/2/1/txchain="7"
nvram set wl1_mimo_preamble="mm"
nvram set wl1_wme_bss_disable="0"
nvram set boardrev="0x1100"
nvram set cstats_path=""
nvram set pptp_client_username=""
nvram set NC_RenewTimeout="0"
nvram set wl0.14_hwaddr="22:CF:30:B7:00:06"
nvram set pci/2/1/phycal_tempdelta="0"
nvram set ppp_passwd=""
nvram set ppp_idletime="5"
nvram set debug_clkfix="1"
nvram set pci/2/1/maxp5gla0="0x40"
nvram set pci/2/1/elna5g="2"
nvram set qos_rst="1"
nvram set bt_blocklist_url="http://list.iblocklist.com/?list=bt_level1"
nvram set wl1_txstreams="0"
nvram set pci/2/1/maxp5gla1="0x40"
nvram set ipv6_tun_v4end="0.0.0.0"
nvram set wl_nctrlsb="upper"
nvram set pci/2/1/maxp5gla2="0x40"
nvram set ne_snat="0"
nvram set log_limit="60"
nvram set vpn_server1_local="10.8.0.1"
nvram set vpn_client1_poll="0"
nvram set bt_ul="100"
nvram set wl0_leddc="0x640000"
nvram set et0macaddr="20:CF:30:B7:00:08"
nvram set vpn_server2_ccd="0"
nvram set bt_rpc_enable="1"
nvram set tor_dnsport="9053"
nvram set vpn_server1_hmac="-1"
nvram set pptp_client_dfltroute="0"
nvram set NC_MaxMissedARP="5"
nvram set wl1_wme_txp_vi="7 3 4 2 0"
nvram set wl1.12_hwaddr="22:CF:30:B7:00:08"
nvram set wan_get_dns="190.0.0.11 200.0.121.11 200.0.1.4"
nvram set ipv6_accept_ra="0"
nvram set wl0_wep_buf=""
nvram set wl0_akm="psk2"
nvram set wl0_radarthrs="1 0x6c0 0x6e0 0x6bc 0x6e0 0x6ac 0x6cc 0x6bc 0x6e0"
nvram set wl_maxassoc="128"
nvram set qosl_enable="0"
nvram set pci/1/1/ledbh12="7"
nvram set watchdog="3000"
nvram set boot_wait="on"
nvram set bt_password="admin"
nvram set wl_phytypes=""
nvram set wl_leddc="0x640000"
nvram set wl1_rifs_advert="auto"
nvram set wl0_infra="1"
nvram set https_crt_gen="0"
nvram set et0mdcport="0"
nvram set wl0_country_code="SG"
nvram set block_wan_limit="1"
nvram set script_init=""
nvram set vpn_client2_nm="255.255.255.0"
nvram set vpn_client2_rgw="0"
nvram set wl1_wme_txp_vo="7 3 4 2 0"
nvram set wl1_wep="disabled"
nvram set pci/2/1/maxp5gha0="0x5E"
nvram set emf_rtport_entry=""
nvram set router_name="TomatoUSB"
nvram set pptp_client_srvip=""
nvram set bt_dl_queue_enable="0"
nvram set t_model_name="Asus RT-N66U"
nvram set pci/2/1/maxp5gha1="0x5E"
nvram set wl1_frag="2346"
nvram set pci/2/1/maxp5gha2="0x5E"
nvram set pci/2/1/pa5gw0a0="0xFEE1"
nvram set wl_distance=""
nvram set https_enable="0"
nvram set wl1_nbw_cap="1"
nvram set wl1_nbw="40"
nvram set pci/2/1/pa5gw0a1="0xFEAC"
nvram set wl_infra="1"
nvram set log_ftp="0"
nvram set pptp_client_srvsubmsk="255.0.0.0"
nvram set pci/2/1/pa5gw0a2="0xFE9B"
nvram set wl_btc_mode="0"
nvram set dr_lan1_tx="0"
nvram set cstats_all="1"
nvram set pmon_ver="CFE 5.100.127"
nvram set ppp_get_ac=""
nvram set wl0_bcn_rotate="1"
nvram set wl_stbc_tx="auto"
nvram set pptp_server_ip=""
nvram set wan_run_mtu="1500"
nvram set pci/2/1/mcsbw20ul5gmpo="0x75311111"
nvram set restore_defaults="0"
nvram set wl1_wpa_gtk_rekey="3600"
nvram set pci/2/1/ccode="0"
nvram set vlan2ports="0 8"
nvram set lan3_netmask=""
nvram set ipv6_get_dns=""
nvram set ne_vbeta="6"
nvram set sch_rboot=""
nvram set wl1_ampdu_rtylimit_tid="5 5 5 5 5 5 5 5"
nvram set wl1_wep_gen=""
nvram set wl0.1_hwaddr="22:CF:30:B7:00:09"
nvram set pci/2/1/extpagain5g="3"
nvram set rruleN="0"
nvram set log_wmsmax="300"
nvram set cifs1=""
nvram set wl1_passphrase=""
nvram set pci/2/1/pa5glw2a0="0xFA8E"
nvram set pci/2/1/boardflags="0x90000200"
nvram set dhcpd_startip="192.168.1.2"
nvram set ppp_username=""
nvram set ppp_get_ip=""
nvram set cifs2=""
nvram set wl1_maclist=""
nvram set pci/2/1/pa5glw2a1="0xFABC"
nvram set wan_lease="3600"
nvram set wl0_wme_sta_be="15 1023 3 0 0 off off"
nvram set wl0_nctrlsb="lower"
nvram set ne_vegas="0"
nvram set wl1.1_hwaddr="22:CF:30:B7:00:0D"
nvram set pci/2/1/pa5glw2a2="0xFABC"
nvram set wl_wme_apsd="on"
nvram set env_path=""
nvram set ftp_anonrate="0"
nvram set pci/2/1/triso5g="3"
nvram set modem_init="*99#"
nvram set wl_radius_ipaddr=""
nvram set http_wanport="8080"
nvram set wl1_amsdu="auto"
nvram set wl1_crypto="aes"
nvram set wl0.7_hwaddr="22:CF:30:B7:00:0F"
nvram set pci/2/1/tempoffset="0"
nvram set lan_gateway="0.0.0.0"
nvram set dhcpd3_startip=""
nvram set usb_ohci="0"
nvram set vpn_server2_c2c="0"
nvram set pci/2/1/mcsbw205gmpo="0x75311111"
nvram set wl0_ifname="eth1"
nvram set usb_storage="1"
nvram set tor_custom=""
nvram set wl1_hw_txchain="7"
nvram set pci/1/1/legofdmbw202gpo="0x55555555"
nvram set lan_domain=""
nvram set dr_lan_rx="0"
nvram set sshd_authkeys=""
nvram set log_file_path="/var/log/messages"
nvram set wl1.7_hwaddr="22:CF:30:B7:00:03"
nvram set pci/1/1/ag0="0"
nvram set wl0_wme_sta_bk="15 1023 7 0 0 off off"
nvram set ct_max="16384"
nvram set vpn_server2_cipher="default"
nvram set qosl_dlc=""
nvram set lan2_ifnames=""
nvram set rrules_activated="0"
nvram set pci/1/1/ag1="0"
nvram set wl0_wds_enable="0"
nvram set vpn_server_eas=""
nvram set limit_br3_dlc=""
nvram set wl1_bss_maxassoc="128"
nvram set pci/1/1/ag2="0"
nvram set lan1_ipaddr=""
nvram set wl_net_reauth="36000"
nvram set wl0_rxchain_pwrsave_quiet_time="1800"
nvram set script_wanup=""
nvram set gpio4="wps_button"
nvram set wl0_rxstreams="0"
nvram set wl_radio_pwrsave_on_time="50"
nvram set vpn_client1_nm="255.255.255.0"
nvram set wl1_radio_pwrsave_on_time="50"
nvram set brau_state=""
nvram set pci/1/1/legofdmbw20ul2gpo="0x55555555"
nvram set modem_dev="ttyUSB0"
nvram set wl1_corerev="29"
nvram set wl1_txpwr="0"
nvram set wl1_nmcsidx="-1"
nvram set gpio7="robo_reset"
nvram set lan_route=""
nvram set wl_macaddr=""
nvram set tor_iface="br0"
nvram set wl1_channel="36"
nvram set wl0_mrate="0"
nvram set wan_gateway="192.168.0.1"
nvram set wl0_mode="ap"
nvram set ntp_kiss_ignore=""
nvram set vpn_server2_plan="1"
nvram set dhcp_start="2"
nvram set ipv6_prefix=""
nvram set vpn_client1_cipher="default"
nvram set wl1_nmode="-1"
nvram set wl0_stbc_tx="auto"
nvram set https_crt_cn=""
nvram set vpn_server2_r1="192.168.1.50"
nvram set pci/2/1/devid="0x4333"
nvram set wl0_ap_isolate="0"
nvram set vpn_server2_r2="192.168.1.55"
nvram set ipv6_service=""
nvram set wl_mrate="0"
nvram set wl0_rxchain_pwrsave_pps="10"
nvram set ddnsx_save="1"
nvram set nf_rtsp="0"
nvram set log_remote="0"
nvram set bt_enable="1"
nvram set wl_akm=""
nvram set wl_wmf_bss_enable="0"
nvram set l2tp_server_ip=""
nvram set dhcpd_gwmode=""
nvram set vpn_client1_addr=""
nvram set NC_DocumentRoot="/tmp/splashd"
nvram set wl0.15_hwaddr="22:CF:30:B7:00:07"
nvram set sromrev="8"
nvram set dhcp_lease="1440"
nvram set wl0_gmode="1"
nvram set wl0_wme_no_ack="off"
nvram set wl0_ampdu="auto"
nvram set nf_sip="1"
nvram set cstats_exclude=""
nvram set vpn_client1_reneg="-1"
nvram set vpn_client1_key=""
nvram set wl1_rts="2347"
nvram set usb_fat_opt=""
nvram set usb_fs_ntfs="1"
nvram set qosl_dlr=""
nvram set pci/2/1/aa5g="7"
nvram set sshd_remote="0"
nvram set smbd_user="admin"
nvram set limit_br3_dlr=""
nvram set NC_BridgeLAN="br0"
nvram set boardtype="0xF5B2"
nvram set wl1_ampdu_rr_rtylimit_tid="2 2 2 2 2 2 2 2"
nvram set ipv6_tun_addrlen="64"
nvram set wl_wme_bss_disable="0"
nvram set wl_obss_coex="0"
nvram set wl_ampdu_rr_rtylimit_tid="2 2 2 2 2 2 2 2"
nvram set multicast_lan="0"
nvram set sshd_hostkey="0000000"
nvram set debug_nocommit="0"
nvram set bt_dl_enable="0"
nvram set limit_br1_dlc=""
nvram set wl_gmode="1"
nvram set wl0_nband="2"
nvram set wl_ampdu="auto"
nvram set ctf_disable="1"
nvram set pci/1/1/rxchain="7"
nvram set vpn_server1_rgw="0"
nvram set vpn_server1_static=""
nvram set wl1_txchain="7"
nvram set wl1.13_hwaddr="22:CF:30:B7:00:09"
nvram set ipv6_ifname="six0"
nvram set wl0_nreqd="0"
nvram set lan_netmask="255.255.255.0"
nvram set ipv6_prefix_length="64"
nvram set wl_mitigation="0"
nvram set wl0_wep_last=""
nvram set wl0_security_mode="wpa2_personal"
nvram set sch_c5_cmd=""
nvram set wl1_obss_coex="0"
nvram set modem_apn="internet"
nvram set wl0_wme_txp_be="7 3 4 2 0"
nvram set wl_nband="2"
nvram set dmz_enable="0"
nvram set vpn_server1_poll="0"
nvram set lan1_ifname=""
nvram set wl1_key="1"
nvram set dhcpd2_endip=""
nvram set wl0_ssid="asus"
nvram set wl0_dtim="1"
nvram set wl_wme_sta_vi="7 15 2 6016 3008 off off"
nvram set http_username=""
nvram set vpn_client1_comp="adaptive"
nvram set pptp_client_mtu="1450"
nvram set wl1_wep_last=""
nvram set rstats_offset="1"
nvram set pci/2/1/pa5ghw2a0="0XFAE4"
nvram set pci/1/1/cckbw202gpo="0x3333"
nvram set wl_wme_ap_be="15 63 3 0 0 off off"
nvram set wl_nreqd="0"
nvram set nf_ttl="0"
nvram set wl0_macaddr=""
nvram set limit_br2_ulc=""
nvram set pci/2/1/pa5ghw2a1="0XFAAE"
nvram set dhcp3_start=""
nvram set wl0_dfs_preism="60"
nvram set os_date="nie, 02 wrz 2012 23:11:29 +0200"
nvram set pci/2/1/pa5ghw2a2="0XFB11"
nvram set wl_tnoise="-99"
nvram set vpn_server1_reneg="-1"
nvram set wl0_wme_txp_bk="7 3 4 2 0"
nvram set http_lanport="80"
nvram set wl_plcphdr="long"
nvram set wl_wme_sta_vo="3 7 2 3264 1504 off off"
nvram set dhcp_routes="1"
nvram set vpn_server1_r1="192.168.1.50"
nvram set pci/1/1/mcsbw20ul2gpo="0xFC955555"
nvram set ppp_redialperiod="10"
nvram set ppp_service=""
nvram set wl_mimo_preamble="mm"
nvram set wl_macmode="disabled"
nvram set script_shut=""
nvram set vpn_server1_r2="192.168.1.55"
nvram set vpn_client2_gw=""
nvram set wl1_wme_ap_be="15 63 3 0 0 off off"
nvram set pci/1/1/pa2gw0a0="0xFE74"
nvram set wan_hwname=""
nvram set dhcp3_lease="1440"
nvram set wl_wme_ap_bk="15 1023 7 0 0 off off"
nvram set wan_domain=""
nvram set vpn_client1_retry="30"
nvram set vpn_client2_port="1194"
nvram set bt_login="admin"
nvram set limit_br1_dlr=""
nvram set pci/1/1/pa2gw0a1="0xFE8F"
nvram set lan_lease="86400"
nvram set wan_netmask="255.255.255.0"
nvram set wl_phytype="b"
nvram set wl0_key1=""
nvram set pci/1/1/parefldovoltage="35"
nvram set pci/1/1/pa2gw0a2="0xFE7F"
nvram set wl_lazywds="1"
nvram set wl0_key2=""
nvram set wl0_vlan_prio_mode="off"
nvram set wl1_rxchain_pwrsave_pps="10"
nvram set wl0.2_hwaddr="22:CF:30:B7:00:0A"
nvram set wan_msroutes=""
nvram set wl0_key3=""
nvram set wl_dfs_postism="60"
nvram set wl0_txant="3"
nvram set jffs2_exec=""
nvram set vpn_server2_key=""
nvram set wl1_radius_key=""
nvram set wl0_key4=""
nvram set wl_mcast_regen_bss_enable="1"
nvram set debug_cprintf_file="0"
nvram set vpn_client_eas=""
nvram set ftp_max="0"
nvram set wl1.2_hwaddr="22:CF:30:B7:00:0E"
nvram set wl1_wme_ap_bk="15 1023 7 0 0 off off"
nvram set pci/1/1/boardflags="0x80001200"
nvram set ppp_demand="0"
nvram set wl0_vifs=""
nvram set wl_auth_mode="none"
nvram set sch_c3_cmd=""
nvram set vpn_client2_crt=""
nvram set new_qoslimit_obw=""
nvram set limit_br3_prio="2"
nvram set wl1_bcn="100"
nvram set wl1_ifname="eth2"
nvram set wl0.8_hwaddr="22:CF:30:B7:00:00"
nvram set pci/2/1/macaddr="20:CF:30:B7:00:0C"
nvram set ppp_keepalive="0"
nvram set mtu_enable="0"
nvram set udpxy_enable="0"
nvram set wl_txant="3"
nvram set qos_orules="0<<-1<d<53<0<<0:10<<0<DNS>0<<-1<d<37<0<<0:10<<0<Time>0<<-1<d<123<0<<0:10<<0<Network Time (NTP)>0<<-1<d<3455<0<<0:10<<0<RSVP>0<<-1<x<9<0<<<<0<SCTP, Discard>0<<-1<x<135,2101,2103,2105<0<<<<0<RPC (Microsoft)>0<<6<x<23,992<0<<<<0<Telnet>0<<-1<d<22<0<<<<3<SSH>0<<17<x<3544<0<<<<3<Teredo port>0<<6<s<80,8080<0<<<<3<Remote Router Access>0<<6<x<3389<0<<<<3<Remote Assistance>0<<-1<a<<0<flash<<<2<Flash Video, (Youtube)>0<<-1<a<<0<httpvideo<<<2<HTTP Video, (Youtube)>0<<-1<a<<0<shoutcast<<<2<Shoutcast>0<<-1<s<6970:7170,8554<0<<<<2<Quicktime/RealAudio>0<<-1<d<1220,7070<0<<<<2<Quicktime/RealAudio>0<<6<x<6005<0<<<<2<Camfrog>0<<-1<d<1220,1234,5100,6005,6970<0<<<<-1<VLC>0<<-1<x<554,5004,5005<0<<<<2<RTP/RTSP>0<<-1<x<1755<0<<<<2<MMS (Microsoft)>0<<-1<x<1935<0<<<<2<RTMP>0<<-1<d<3478,3479,5060:5063<0<<<<1<SIP, Sipgate Stun Services>0<<-1<d<1718:1720<0<<<<1<H323>0<<-1<a<<0<skypetoskype<<<1<Skype>0<<-1<a<<0<skypeout<<<1<Skypeout>0<<-1<d<80<0<<0:512<<4<HTTP>0<<-1<d<443<0<<0:512<<4<HTTPS>0<<6<d<8080<0<<0:512<<4<HTTP Proxy / Alternate>0<<-1<d<25,587,465<0<<<<5<SMTP, Submission>0<<-1<d<110,995<0<<<<5<POP3 Mail>0<<-1<d<119,563<0<<<<5<NNTP>0<<-1<d<143,220,585,993<0<<<<5<IMAP Mail>0<<-1<a<<0<irc<<<6<IRC>0<<-1<d<1493,1502,1503,1542,1863,1963,3389,5061,5190:5193,7001<0<<<<6<Windows Live>0<<-1<d<1071:1074,1455,1638,1644,5000:5010,5050,5100,5101,5150,8000:8002<0<<<<6<Yahoo Messenger>0<<-1<d<194,1720,1730:1732,5220:5223,5298,6660:6669,22555<0<<<<6<Other Chat Services>0<<6<d<20,21,989,990<0<<<<7<FTP>0<<-1<x<6571,6891:6901<0<<<<7<WLM File/Webcam>0<<6<d<80,443,8080<0<<512:<<7<HTTP,SSL File Transfers>0<<17<x<1:65535<0<<<<-1<P2P (uTP, UDP)"
nvram set vpn_server2_if="tun"
nvram set sshd_pass="1"
nvram set debug_ddns="0"
nvram set limit_br2_ulr=""
nvram set vlan2hwname="et0"
nvram set cstats_include=""
nvram set wl1.8_hwaddr="22:CF:30:B7:00:04"
nvram set wl1_wep_buf=""
nvram set pci/1/1/tempoffset="0"
nvram set udpxy_clients="3"
nvram set sesx_b0="1"
nvram set wl0_hw_rxchain="7"
nvram set wl_wpa_psk=""
nvram set wl0_rxchain_pwrsave_enable="1"
nvram set http_passwd="admin"
nvram set remote_mgt_https="0"
nvram set sshd_forwarding="0"
nvram set sesx_b1="4"
nvram set wl1_auth_mode="none"
nvram set rrules_radio="-1"
nvram set lan2_ipaddr=""
nvram set block_wan="1"
nvram set sesx_b2="4"
nvram set lan_stp="0"
nvram set sesx_b3="4"
nvram set usb_automount="1"
nvram set wl0_wme_ap_vi="7 15 1 6016 3008 off off"
nvram set script_usbhotplug=""
nvram set ftp_users=""
nvram set vpn_client2_hmac="-1"
nvram set pptp_client_mtuenable="0"
nvram set wl_mode="ap"
nvram set ct_timeout="600 30"
nvram set wl0_bss_maxassoc="128"
nvram set usb_fs_ext3="1"
nvram set ntp_kiss=""
nvram set log_wmdmax="300"
nvram set qos_ibw="1000"
nvram set tor_datadir="/tmp/tor"
nvram set wl1_mcast_regen_bss_enable="1"
nvram set wl0_closed="0"
nvram set wl0_rate="0"
nvram set wl0_plcphdr="long"
nvram set wl0.10_hwaddr="22:CF:30:B7:00:02"
nvram set xtalfreq="25000"
nvram set wl_wpa_gtk_rekey="3600"
nvram set wl0_macmode="disabled"
nvram set vpn_client1_gw=""
nvram set vpn_client2_cipher="default"
nvram set new_qoslimit_rules=""
nvram set limit_br1_prio="2"
nvram set lan_dhcp="0"
nvram set wl0_radioids="BCM2059"
nvram set wl0_wme_ap_vo="3 7 1 3264 1504 off off"
nvram set pci/1/1/boardvendor="0x14E4"
nvram set dhcp3_num=""
nvram set wl0_phytype="h"
nvram set wl_wme_txp_vi="7 3 4 2 0"
nvram set nfs_enable="0"
nvram set vpn_client2_crypt="tls"
nvram set wl0_lazywds="1"
nvram set dr_wan_rx="0"
nvram set wl1_radioids="BCM2059"
nvram set pci/2/1/mcsbw20ul5glpo="0x00000000"
nvram set dhcpd_endip="192.168.1.51"
nvram set ntp_tdod="0"
nvram set cstats_offset="1"
nvram set snmp_remote_sip=""
nvram set sch_c1_cmd=""
nvram set wl1_rxchain_pwrsave_quiet_time="1800"
nvram set nf_l7in="1"
nvram set smbd_cpage="437"
nvram set bt_pex="1"
nvram set NC_GatewayPort="5280"
nvram set boardflags2="0x00000000"
nvram set upnp_ssdp_interval="60"
nvram set usb_mmc="1"
nvram set ftp_enable="2"
nvram set vpn_server1_pdns="0"
nvram set pci/2/1/pa5glw1a0="0x1637"
nvram set t_fix1="TomatoUSB"
nvram set pptp_client_enable="0"
nvram set smbd_nlsmod="nls_cp437"
nvram set wl1_nctrlsb="lower"
nvram set pci/2/1/pa5glw1a1="0x1591"
nvram set wl0_afterburner="off"
nvram set wl_wme_txp_vo="7 3 4 2 0"
nvram set dr_lan_tx="0"
nvram set upnp_clean="1"
nvram set vpn_client2_nat="1"
nvram set pci/2/1/pa5glw1a2="0x1591"
nvram set lan_hwaddr="20:CF:30:B7:00:08"
nvram set wl_wds_timeout="1"
nvram set wl0_antdiv="3"
nvram set vpn_server1_if="tun"
nvram set bt_ratio_idle_enable="1"
nvram set wan_dns=""
nvram set ddnsx_refresh="28"
nvram set vpn_server1_custom=""
nvram set btn_reset=""
nvram set wl1.14_hwaddr="22:CF:30:B7:00:0A"
nvram set action_service=""
nvram set pci/2/1/mcsbw205glpo="0x00000000"
nvram set vpn_server2_static=""
nvram set bt_dl_queue_size="5"
nvram set bt_ul_queue_size="5"
nvram set pci/1/1/triso2g="3"
nvram set lan3_stp="0"
nvram set wl_ssid="Tomato24"
nvram set wl_dtim="1"
nvram set lan3_ifnames=""
nvram set wl1_frameburst="off"
nvram set pci/1/1/sromrev="9"
nvram set wl0_wpa_psk="1234567890123"
nvram set wl_radarthrs="1 0x6c0 0x6e0 0x6bc 0x6e0 0x6ac 0x6cc 0x6bc 0x6e0"
nvram set dns_addget="0"
nvram set routes_static=""
nvram set usb_ext_opt=""
nvram set snmp_location="router"
nvram set vpn_server1_remote="10.8.0.2"
nvram set vpn_client1_adns="0"
nvram set t_model="34"
nvram set pci/2/1/mcsbw20ul5ghpo="0x75311111"
nvram set pci/1/1/extpagain2g="3"
nvram set wait_time="5"
nvram set lan2_ifname=""
nvram set pci/2/1/legofdmbw205gmpo="0x75311111"
nvram set web_wl_filter="0"
nvram set vpn_server2_crypt="tls"
nvram set pci/2/1/temps_period="5"
nvram set pci/1/1/venid="0x14E4"
nvram set wl0_amsdu="auto"
nvram set upnp_clean_interval="600"
nvram set wl_passphrase=""
nvram set t_cafree="1"
nvram set usb_printer="0"
nvram set dhcp1_num=""
nvram set telnetd_eas="0"
nvram set cstats_labels="0"
nvram set wl1_radarthrs="1 0x6c0 0x6e0 0x6bc 0x6e0 0x6ac 0x6cc 0x6bc 0x6e0"
nvram set pci/2/1/ledbh12="7"
nvram set multicast_pass="0"
nvram set bt_check="1"
nvram set log_remoteport="514"
nvram set vpn_client1_static=""
nvram set bt_binary="internal"
nvram set wan_proto="dhcp"
nvram set wl_key1=""
nvram set wl_amsdu="auto"
nvram set rstats_stime="48"
nvram set vpn_server1_comp="adaptive"
nvram set wl1_afterburner="off"
nvram set pci/2/1/mcsbw205ghpo="0x75311111"
nvram set wl_key2=""
nvram set usb_usb2="1"
nvram set wl1_stbc_tx="auto"
nvram set wl_key3=""
nvram set wl0_unit="0"
nvram set vpn_client2_if="tun"
nvram set secret_code="19178752"
nvram set wl_country_code="US"
nvram set wl_key4=""
nvram set tm_dst="1"
nvram set vpn_server2_dhcp="1"
nvram set wl_hwaddr=""
nvram set wl0_txpwr="0"
nvram set vpn_server1_ccd_val=""
nvram set vpn_server1_crt=""
nvram set wl0.3_hwaddr="22:CF:30:B7:00:0B"
nvram set wl1_sta_retry_time="5"
nvram set wl_vifs=""
nvram set wl0_net_reauth="36000"
nvram set wl0_bss_enabled="1"
nvram set rstats_exclude=""
nvram set wan_ifnameX="vlan2"
nvram set wl_vlan_prio_mode="off"
nvram set usb_ntfs_opt=""
nvram set wl1.3_hwaddr="22:CF:30:B7:00:0F"
nvram set lan1_stp="0"
nvram set wl0_nmode="-1"
nvram set udpxy_stats="0"
nvram set https_crt_file=""
nvram set vpn_server2_port="1194"
nvram set wl0.9_hwaddr="22:CF:30:B7:00:01"
nvram set wl_net_mode="mixed"
nvram set wl_txpwr="42"
nvram set bt_auth="1"
nvram set routes_static_saved=""
nvram set wl_rifs_advert="auto"
nvram set qos_syn="1"
nvram set snmp_remote="0"
nvram set jumbo_frame_size="2000"
nvram set bt_binary_custom="/path/to/binaries/directory"
nvram set wl1.9_hwaddr="22:CF:30:B7:00:05"
nvram set modem_pin=""
nvram set wl_nmode="-1"
nvram set web_mx="status,bwm"
nvram set usb_irq_thresh="0"
nvram set NC_HomePage="http://google.com"
nvram set wl1_bcn_rotate="1"
nvram set lan3_ipaddr=""
nvram set rstats_data=""
nvram set limit_br1_enable="0"
nvram set pci/1/1/maxp2ga0="0x64"
nvram set log_file_custom="0"
nvram set bt_port_gui="9091"
nvram set pci/1/1/maxp2ga1="0x64"
nvram set wl_rxstreams="0"
nvram set vpn_client2_proto="udp"
nvram set pci/1/1/maxp2ga2="0x64"
nvram set wl0_wds=""
nvram set macnames=""
nvram set qos_ack="0"
nvram set qos_burst0=""
nvram set wl1_macaddr=""
nvram set ppp_static_ip=""
nvram set wl_rate="0"
nvram set qos_burst1=""
nvram set cstats_bak="0"
nvram set bt_settings="down_dir"
nvram set wan_routes1=""
nvram set wl1_wme_sta_be="15 1023 3 0 0 off off"
nvram set pci/2/1/pa5ghw1a0="0X158D"
nvram set wan_routes2=""
nvram set wl1_closed="0"
nvram set pci/2/1/pa5ghw1a1="0X1543"
nvram set wl0_reg_mode="off"
nvram set pptp_dhcp="1"
nvram set ntp_server="0.europe.pool.ntp.org 1.europe.pool.ntp.org 2.europe.pool.ntp.org"
nvram set pptp_client_peerdns="0"
nvram set bt_rpc_wan="0"
nvram set wl1_bss_enabled="1"
nvram set pci/2/1/parefldovoltage="60"
nvram set pci/2/1/pa5ghw1a2="0X1504"
nvram set wan_hwaddr="20:CF:30:B7:00:09"
nvram set nf_pptp="1"
nvram set vpn_client2_poll="0"
nvram set wl1_rxstreams="0"
nvram set wl0.11_hwaddr="22:CF:30:B7:00:03"
nvram set wan_gateway_get="192.168.0.1"
nvram set log_file_size="50"
nvram set NC_GatewayName="Tomato Captive Portal"
nvram set wl1_reg_mode="off"
nvram set wl1_akm="psk2"
nvram set dhcpd1_endip=""
nvram set vpn_server2_hmac="-1"
nvram set vpn_client1_if="tun"
nvram set lan_ifnames="vlan1 eth1 eth2"
nvram set pppoe_ifname=""
nvram set tor_users="192.168.1.0/24"
nvram set wl1_wme_sta_bk="15 1023 7 0 0 off off"
nvram set wl0_auth="0"
nvram set wl0_wme="on"
nvram set wl0_radius_port="1812"
nvram set wl0_mac_deny=""
nvram set vpn_client2_rg="0"
nvram set wl1_wds_enable="0"
nvram set dhcp2_start=""
nvram set wl_rxchain_pwrsave_quiet_time="1800"
nvram set block_wan_limit_icmp="1"
nvram set upnp_port="0"
nvram set rstats_path=""
nvram set wl0_rxchain="7"
nvram set lan_hostname="tomatoUSB"
nvram set modem_ipaddr="0.0.0.0"
nvram set ipv6_rtr_addr=""
nvram set wl1_radio="1"
nvram set wl0_mitigation="0"
nvram set wl0_radius_ipaddr=""
nvram set wl0_wme_bss_disable="0"
nvram set sshd_port="22"
nvram set vpn_server2_sn="10.8.0.0"
nvram set wl1_mac_deny=""
nvram set wl_radio_pwrsave_pps="10"
nvram set pci/1/1/boardflags2="0x00100000"
nvram set pppoe_lef=""
nvram set wl0_wme_sta_vi="7 15 2 6016 3008 off off"
nvram set qos_classnames="Service VOIP/Game Media Remote WWW Mail Messenger Download P2P/Bulk Crawl"
nvram set web_css="usbblue"
nvram set sesx_script="[ \$1 -ge 20 ] && telnetd -p 233 -l /bin/sh "
nvram set ms_dirs="/mnt<"
nvram set ms_dbdir=""
nvram set wl1_antdiv="3"
nvram set pa0maxpwr="400"
nvram set vpn_server2_proto="udp"
nvram set pci/1/1/tssipos2g="1"
nvram set dhcp2_lease="1440"
nvram set pppoe_lei=""
nvram set mac_wan=""
nvram set ftp_rate="0"
nvram set vpn_server2_custom=""
nvram set vpn_server2_ca=""
nvram set pci/2/1/pa5gw2a0="0xFAF7"
nvram set wl1.15_hwaddr="22:CF:30:B7:00:0B"
nvram set pci/2/1/mcsbw405gmpo="0x75311111"
nvram set pci/2/1/pa5gw2a1="0xFA82"
nvram set trigforward="0<1<3000:4000<5000:6000<ex: open 5000-6000 if 3000-4000>"
nvram set remote_management="0"
nvram set smbd_custom=""
nvram set wan_ifnames="vlan2"
nvram set pci/2/1/pa5gw2a2="0xFAAC"
nvram set pci/1/1/ledbh0="2"
nvram set wan_islan="0"
nvram set wl_rateset="default"
nvram set wl_crypto="aes"
nvram set wl0_wme_sta_vo="3 7 2 3264 1504 off off"
nvram set NC_ExcludePorts="1863"
nvram set wl1_ap_isolate="0"
nvram set pci/1/1/ledbh1="5"
nvram set block_wan_limit_tr="5"
nvram set dmz_sip=""
nvram set vpn_server1_firewall="auto"
nvram set vpn_server2_remote="10.8.0.2"
nvram set lan3_ifname=""
nvram set wl1_security_mode="wpa2_personal"
nvram set pci/1/1/ledbh2="4"
nvram set ddnsx1_cache=""
nvram set usb_fs_fat="1"
nvram set vpn_server1_ccd="0"
nvram set wl1_radio_pwrsave_quiet_time="1800"
nvram set pci/2/1/ledbh0="2"
nvram set pci/1/1/ledbh3="11"
nvram set ppp_mru="1500"
nvram set ipv6_tun_mtu="0"
nvram set wl_wep_bit="128"
nvram set wl1_wme_no_ack="off"
nvram set pci/2/1/ledbh1="5"
nvram set pci/1/1/mcs32po="0x9999"
nvram set vpn_server2_firewall="auto"
nvram set tor_enable="0"
nvram set wl1_radius_port="1812"
nvram set wl_ifnames="eth1 eth2"
nvram set pci/2/1/ledbh2="4"
nvram set pci/2/1/legofdmbw20ul5gmpo="0x75311111"
nvram set lan_ipaddr="192.168.1.1"
nvram set clkfreq="600,300,150"
nvram set lan_proto="dhcp"
nvram set wl_radius_key=""
nvram set portforward="0<3<1.1.1.0/24<1000:2000<<192.168.1.2<ex: 1000 to 2000, restricted>0<2<<1000,2000<<192.168.1.2<ex: 1000 and 2000>0<1<<1000<2000<192.168.1.2<ex: different internal port>0<3<<1000:2000,3000<<192.168.1.2<ex: 1000 to 2000, and 3000>"
nvram set ipv6_portforward=""
nvram set smbd_passwd="admin"
nvram set nfs_exports=""
nvram set bt_check_time="15"
nvram set os_name="linux"
nvram set pci/2/1/ledbh3="11"
nvram set pci/2/1/rxchain="7"
nvram set pci/1/1/legofdm40duppo="0x4444"
nvram set vlan1hwname="et0"
nvram set lan1_netmask=""
nvram set wl_rxchain_pwrsave_enable="1"
nvram set dhcpd_dmdns="1"
nvram set wl0_maxassoc="128"
nvram set vpn_client1_custom=""
nvram set wl0_radio_pwrsave_on_time="50"
nvram set cstats_stime="48"
nvram set debug_cprintf="0"
nvram set wl1_plcphdr="long"
nvram set wl_unit="0"
nvram set dr_wan_tx="0"
nvram set vpn_client2_static=""
nvram set wl1_maxassoc="128"
nvram set wl1_macmode="disabled"
nvram set wl0_phytypes="h"
nvram set vpn_client1_rgw="0"
nvram set pci/2/1/pdetrange5g="0"
nvram set wl0_wep="disabled"
nvram set wl0_frag="2346"
nvram set wl_nmode_protection="off"
nvram set ct_tcp_timeout="0 1200 120 60 120 120 10 60 30 0"
nvram set vpn_client1_remote="10.8.0.1"
nvram set bt_ul_enable="1"
nvram set wl1_phytype="h"
nvram set dhcpd1_startip=""
nvram set snmp_ro="rocommunity"
nvram set vpn_client1_rg="0"
nvram set bt_port="51515"
nvram set wl1_lazywds="1"
nvram set wl1_phytypes="h"
nvram set wl_radio_pwrsave_enable="0"
nvram set ftp_dirlist="0"
nvram set wl0.4_hwaddr="22:CF:30:B7:00:0C"
nvram set wl0_nbw="40"
nvram set wl0_distance=""
nvram set vpn_server1_sn="10.8.0.0"
nvram set wl1_wme_txp_be="7 3 4 2 0"
nvram set sdram_config="0x0000"
nvram set pci/1/1/antswctl2g="0"
nvram set ppp_ac=""
nvram set usb_noled="1-1.4"
nvram set wl0_btc_mode="0"
nvram set wl0_country="SG"
nvram set wl1.4_hwaddr="22:CF:30:B7:00:00"
nvram set wl1_distance=""
nvram set vlan1ports="4 3 2 1 8*"
nvram set dmz_ipaddr="0"
nvram set pci/2/1/legofdm40duppo="0x2222"
nvram set pci/2/1/maxp5ga0="0x5E"
nvram set pci/2/1/pa5glw0a0="0xFE87"
nvram set wl_wds=""
nvram set log_wmtype="0"
nvram set wl1_dfs_preism="60"
nvram set wl1_btc_mode="0"
nvram set pci/2/1/maxp5ga1="0x5E"
nvram set pci/2/1/pa5glw0a1="0xFE9A"
nvram set script_brau=""
nvram set usb_uhci="-1"
nvram set vpn_server1_ca=""
nvram set vpn_client1_crypt="tls"
nvram set pci/2/1/maxp5ga2="0x5E"
nvram set pci/2/1/pa5glw0a2="0xFE9A"
nvram set wl0_tnoise="-76"
nvram set smbd_wgroup="WORKGROUP"
nvram set wl1_wme_txp_bk="7 3 4 2 0"
nvram set wl1_mode="ap"
nvram set script_fire=""
nvram set wl1_rxchain_pwrsave_enable="1"
nvram set wl0_rateset="default"
nvram set wl0_ampdu_rr_rtylimit_tid="2 2 2 2 2 2 2 2"
nvram set pci/1/1/txchain="7"
nvram set usb_fs_hfs="0"
nvram set vpn_debug="0"
nvram set wl1_wpa_psk="1234567890123"
nvram set pci/1/1/elna2g="2"
nvram set wl0_wme_apsd="on"
nvram set log_file="1"
nvram set ftp_sip=""
nvram set bt_lpd="1"
nvram set limit_br2_enable="0"
nvram set upnp_lan="1"
nvram set wl0_wep_bit="128"
nvram set wl0_wme_txp_vi="7 3 4 2 0"
nvram set vpn_server1_c2c="0"
nvram set vpn_client2_key=""
nvram set wl_wme="auto"
nvram set wl0_txstreams="0"
nvram set vpn_client2_addr=""
nvram set wl1_wme_apsd="on"
nvram set wl0_ifnames="eth1 eth2"
nvram set pci/2/1/legofdmbw205glpo="0x00000000"
nvram set pci/1/1/antswitch="0"
nvram set pci/1/1/aa2g="7"
nvram set pci/2/1/venid="0x14E4"
nvram set wan_primary="1"
nvram set wl_wme_ap_vi="7 15 1 6016 3008 off off"
nvram set ne_shlimit="1,3,60"
nvram set sshd_rport="22"
nvram set lan_ifname="br0"
nvram set boardflags="0x00000110"
nvram set wl0_mimo_preamble="mm"
nvram set rstats_bak="0"
nvram set sch_c1=""
nvram set limit_br2_dlc=""
nvram set sdram_refresh="0x0000"
nvram set wandevs="vlan2"
nvram set dhcp_pass="1"
nvram set smbd_cset="utf8"
nvram set ms_stdlna="0"
nvram set sch_c2=""
nvram set pptp_client_nat="0"
nvram set pptp_client_crypt="0"
nvram set dhcp_domain="wan"
nvram set wl0_wme_txp_vo="7 3 4 2 0"
nvram set dr_lan3_rx="0"
nvram set qos_icmp="0"
nvram set log_wm="0"
nvram set sch_c3=""
nvram set wl0.12_hwaddr="22:CF:30:B7:00:04"
nvram set wl_auth="0"
nvram set dhcpd_static_only="0"
nvram set trunk_vlan_so="0"
nvram set web_svg="1"
nvram set sch_c4=""
nvram set vpn_server2_rgw="0"
nvram set sdram_ncdl="0x00000000"
nvram set pci/1/1/temps_hysteresis="5"
nvram set ipv6_tun_addr=""
nvram set wl_wep_last=""
nvram set https_crt_save="0"
nvram set sch_c5=""
nvram set tor_transport="9040"
nvram set wl1_wme_ap_vi="7 15 1 6016 3008 off off"
nvram set wl_wme_ap_vo="3 7 1 3264 1504 off off"
nvram set ne_valpha="2"
nvram set rmgt_sip=""
nvram set vpn_server1_crypt="tls"
nvram set vpn_server1_plan="1"
nvram set vpn_client2_local="10.8.0.2"
nvram set vpn_client2_ca=""
nvram set wl1_wmf_bss_enable="0"
nvram set pci/2/1/boardvendor="0x14E4"
nvram set dhcpd_lmax=""
nvram set wan_iface="vlan2"
nvram set wl1_hw_rxchain="7"
nvram set wl_frameburst="off"
nvram set wl_bss_maxassoc="128"
nvram set ms_tivo="0"
nvram set vpn_server2_ccd_val=""
nvram set vpn_server2_dh=""
nvram set wl0_nmode_protection="off"
nvram set wl0_radio_pwrsave_pps="10"
nvram set vpn_server2_poll="0"
nvram set vpn_client1_bridge="1"
nvram set new_qoslimit_enable="0"
nvram set qosl_ulc=""
nvram set NC_enable="0"
nvram set wl1_dtim="1"
nvram set pci/2/1/legofdmbw205ghpo="0x75311111"
nvram set wl1_ssid="asus_5g"
nvram set vpn_client2_comp="adaptive"
nvram set limit_br3_ulc=""
nvram set wl1.10_hwaddr="22:CF:30:B7:00:06"
nvram set jffs2_format="0"
nvram set dmz_ifname="br0"
nvram set qos_enable="0"
nvram set vpn_server1_ccd_excl="0"
nvram set wl1_wme_ap_vo="3 7 1 3264 1504 off off"
nvram set pci/1/1/temps_period="5"
nvram set wan_ipaddr="192.168.0.2"
nvram set dhcp_num="50"
nvram set ipv6_tun_ttl="255"
nvram set sch_rcon=""
nvram set bt_ratio_enable="1"
nvram set wl0_passphrase=""
nvram set log_file_keep="1"
nvram set pci/2/1/antswitch="0"
nvram set vpn_server2_ccd_excl="0"
nvram set wl0_rts="2347"
nvram set http_id="TID1a4f65ddc3b00000"
nvram set smbd_wins="1"
nvram set bt_custom=""
nvram set limit_br2_dlr=""
nvram set pci/1/1/cckbw20ul2gpo="0x3333"
nvram set wan_wins=""
nvram set wl_ifname="eth1"
nvram set upnp_clean_threshold="20"
nvram set pci/1/1/leddc="0xFFFF"
nvram set wl_wep="disabled"
nvram set wl_nbw_cap="1"
nvram set wl_ampdu_rtylimit_tid="5 5 5 5 5 5 5 5"
nvram set btn_override=""
nvram set http_enable="1"
nvram set wl1_nmode_protection="off"
nvram set wl1_key1=""
nvram set wl0_hw_txchain="7"
nvram set pci/2/1/tempthresh="120"
nvram set pci/1/1/pa2gw2a0="0xF980"
nvram set wl1_key2=""
nvram set pci/1/1/pa2gw2a1="0xF924"
nvram set wan_speed="4"
nvram set dhcpc_custom=""
nvram set https_lanport="443"
nvram set vpn_server2_local="10.8.0.1"
nvram set os_version="1.28.0000 MIPSR2-101 K26 USB AIO-64K"
nvram set wl1_key3=""
nvram set pci/1/1/pa2gw2a2="0xF9C8"
nvram set wl_gmode_protection="off"
nvram set wl_nbw="40"
nvram set wl1_key4=""
nvram set wl1_leddc="0x640000"
nvram set wl0_wpa_gtk_rekey="3600"
nvram set dhcpd_static=""
nvram set dnsmasq_custom=""
nvram set dnsmasq_static_only="0"
nvram set ne_syncookies="0"
nvram set web_pb=""
nvram set ppp_get_srv=""
nvram set wl0_sta_retry_time="5"
nvram set ftp_pvtroot=""
nvram set sch_c4_cmd=""
nvram set vpn_client2_custom=""
nvram set pci/2/1/pa5ghw0a0="0XFEDC"
nvram set pci/1/1/phycal_tempdelta="0"
nvram set wl_frag="2346"
nvram set dr_lan2_rx="0"
nvram set qosl_ulr=""
nvram set wl1_vifs=""
nvram set pci/2/1/pa5ghw0a1="0XFEB0"
nvram set pci/2/1/sromrev="9"
nvram set ipv6_radvd="1"
nvram set wl0_key="1"
nvram set wl_wep_gen=""
nvram set wan_mtu="1500"
nvram set bt_ratio_idle="15"
nvram set limit_br3_ulr=""
nvram set pci/2/1/pa5ghw0a2="0XFEDD"
nvram set qos_obw="230"
nvram set ftp_limit="0,3,60"
nvram set emf_entry=""
nvram set wl_maclist=""
nvram set vpn_client1_proto="udp"
nvram set vpn_client1_firewall="auto"
nvram set vpn_client1_ca=""
nvram set vpn_client2_remote="10.8.0.1"
nvram set limit_br1_ulc=""
nvram set wl1_infra="1"
nvram set ne_vgamma="2"
nvram set et0phyaddr="30"
nvram set console_loglevel="1"
nvram set smbd_master="1"
nvram set vpn_server1_dh=""
nvram set wl0.5_hwaddr="22:CF:30:B7:00:0D"
nvram set bl_version="1.0.1.2"
nvram set wl_bcn_rotate="1"
nvram set ct_hashsize="2048"
nvram set ftp_super="0"
nvram set vpn_client2_firewall="auto"
nvram set NC_LoginTimeout="3600"
nvram set wl1_rxchain="7"
nvram set qos_default="8"
nvram set vpn_client1_port="1194"
nvram set qosl_udp="0"
nvram set wan_get_domain=""
nvram set rstats_sshut="1"
nvram set usb_printer_bidirect="0"
nvram set wan_6rd=""
nvram set wl1.5_hwaddr="22:CF:30:B7:00:01"
nvram set pci/2/1/antswctl5g="0"
nvram set bt_peer_limit_per_torrent="100"
nvram set wan_ifname="vlan2"
nvram set wl_wme_sta_be="15 1023 3 0 0 off off"
nvram set dns_norebind="1"
nvram set wl1_tnoise="-82"
nvram set wl_radioids=""
nvram set tm_sel="CET-1CEST,M3.5.0/2,M10.5.0/3"
nvram set vpn_server1_key=""
nvram set pptp_client_srvsub="10.0.0.0"
nvram set wl1_rate="0"
nvram set landevs="vlan1 wl0 wl1"
nvram set wl_security_mode="disabled"
nvram set wl0_dfs_postism="60"
nvram set wan_hostname="tomatoUSB"
nvram set pci/2/1/pa5gw1a0="0x1663"
nvram set dhcp1_start=""
nvram set ppp_mtu="1500"
nvram set wl_corerev=""
nvram set wl0_radio="1"
nvram set wl_nmcsidx="-1"
nvram set limit_br2_prio="2"
nvram set pci/2/1/mcsbw405glpo="0x00000000"
nvram set pci/2/1/pa5gw1a1="0x1676"
nvram set wl0_nbw_cap="1"
nvram set ftp_staytimeout="300"
nvram set limit_br3_enable="0"
nvram set pci/2/1/pa5gw1a2="0x15FA"
nvram set wl_channel="6"
nvram set sch_c2_cmd=""
nvram set vpn_client1_crt=""
nvram set bt_ratio="1.0000"
nvram set bt_sleep="10"
nvram set wl0_bcn="100"
nvram set wl_wme_sta_bk="15 1023 7 0 0 off off"
nvram set manual_boot_nv="0"
nvram set ntp_updates="4"
nvram set wl_wds_enable="0"
nvram set ms_sas="0"
nvram set vpn_server1_proto="udp"
nvram set limit_br1_ulr=""
nvram set NC_PeerChecktimeout="0"
nvram set wl1_radio_pwrsave_enable="0"
nvram set dhcp1_lease="1440"
nvram set ppp_static="0"
nvram set wl0_hwaddr="20:CF:30:B7:00:08"
nvram set wl_radio="1"
nvram set wl_afterburner="off"
nvram set bt_dht="1"
nvram set bt_utp="1"
nvram set wl1_net_reauth="36000"
nvram set pci/1/1/ccode="0"
nvram set wan_routes=""
nvram set vpn_server2_pdns="0"
nvram set pci/2/1/legofdmbw20ul5glpo="0x00000000"
nvram set lan2_netmask=""
nvram set wl0_ampdu_rtylimit_tid="5 5 5 5 5 5 5 5"
nvram set ddnsx0=""
nvram set jumbo_frame_enable="0"
nvram set dr_lan1_rx="0"
nvram set qos_orates="5-20,5-20,5-25,5-70,20-100,5-80,5-80,5-80,5-50,0-0"
nvram set pci/2/1/ag0="0"
nvram set wl0_wep_gen=""
nvram set emf_enable="0"
nvram set ddnsx1=""
nvram set ftp_ipmax="0"
nvram set vpn_client1_hmac="-1"
nvram set wl0.13_hwaddr="22:CF:30:B7:00:05"
nvram set pci/2/1/ag1="0"
nvram set wl0_gmode_protection="off"
nvram set wk_mode="gateway"
nvram set sshd_eas="1"
nvram set rstats_enable="1"
nvram set script_usbmount=""
nvram set pci/2/1/ag2="0"
nvram set ddnsx0_cache=""
nvram set wl0_maclist=""
nvram set ms_enable="0"
nvram set bt_ul_slot_per_torrent="10"
nvram set new_qoslimit_ibw=""
nvram set wl0_obss_coex="0"
nvram set wl_radio_pwrsave_quiet_time="1800"
nvram set rstats_colors=""
nvram set NC_GatewayMode="Open"
nvram set sdram_init="0x0000"
nvram set pci/2/1/mcsbw405ghpo="0x75311111"
nvram set wl_rts="2347"
nvram set dhcpd2_startip=""
nvram set nf_h323="1"
nvram set dhcpd_slt="0"
nvram set wl1_dfs_postism="60"
nvram set lan_wins=""
nvram set wl_ap_isolate="0"
nvram set log_out="0"
nvram set vpn_client2_adns="0"
nvram set lan_hwnames=""
nvram set vpn_client2_bridge="1"
nvram set bt_incomplete="1"
nvram set NC_IdleTimeout="0"
nvram set wl1.11_hwaddr="22:CF:30:B7:00:07"
nvram set wl1_radius_ipaddr=""
nvram set wl1_mrate="0"
nvram set ftp_pubroot=""
nvram set lan1_ifnames=""
nvram set wl1_country="SG"
nvram set wl1_country_code="SG"
nvram set pci/2/1/boardflags2="0x00200000"
nvram set dhcp2_num=""
nvram set wl_wme_no_ack="off"
nvram set ftp_port="21"
nvram set pci/2/1/legofdmbw20ul5ghpo="0x75311111"
nvram set dhcpc_minpkt="1"
nvram set multicast_lan1="0"
nvram set wl1_gmode_protection="off"
nvram set regulation_domain="US"
nvram set wl0_radius_key=""
nvram set multicast_lan2="0"
nvram set pci/1/1/pdetrange2g="0"
nvram set wl0_wme_ap_be="15 63 3 0 0 off off"
nvram set multicast_lan3="0"
nvram set rrulewp="80,8080"
nvram set smbd_shares="jffs</jffs<JFFS<1<0>root\$</<Hidden Root<0<1"
nvram set wl0_corerev="29"
nvram set wl0_nmcsidx="-1"
nvram set wl1_rateset="default"
nvram set ipv6_relay="1"
nvram set wl_key="1"
nvram set log_wmip=""
nvram set snmp_enable="0"
nvram set vpn_server2_comp="adaptive"
nvram set wl1_ampdu="auto"
nvram set wl1_gmode="1"
nvram set regulation_domain_5G="Q2"
nvram set pci/1/1/regrev="39"
nvram set wl0_channel="1"
nvram set nf_ftp="1"
nvram set ftp_anonymous="0"
nvram set vpn_client1_nat="1"
nvram set vpn_client2_reneg="-1"
nvram set wl1_unit="1"
nvram set wl0_wds_timeout="1"
nvram set sshd_dsskey="00000"
nvram set usb_enable="1"
nvram set vpn_server2_crt=""
nvram set wl1_wep_bit="128"
nvram set nf_loopback="0"
nvram set log_mark="60"
nvram set ftp_custom=""
nvram set NC_ForcedRedirect="0"
nvram set pci/2/1/regrev="2"
nvram set pci/1/1/devid="0x4332"
nvram set wl0_wme_ap_bk="15 1023 7 0 0 off off"
nvram set wl_bss_enabled="1"
nvram set dr_setting="0"
nvram set upnp_enable="3"
nvram set log_events=""
nvram set pptp_client_custom=""
nvram set wl1_mitigation="0"
nvram set wl_wme_txp_be="7 3 4 2 0"
nvram set dr_lan3_tx="0"
nvram set script_usbumount=""
nvram set ftp_anonroot=""
nvram set bt_settings_custom="/tmp/btclient"
nvram set pci/1/1/tempthresh="120"
nvram set lan2_stp="0"
nvram set wl1_nband="1"
nvram set dns_intcpt="0"
nvram set qos_fin="1"
nvram set vpn_server2_nm="255.255.255.0"
nvram set tor_socksport="9050"
nvram set wl1_wme_sta_vi="7 15 2 6016 3008 off off"
nvram set pci/1/1/mcsbw402gpo="0xFFFF9999"
nvram set pci/1/1/macaddr="20:CF:30:B7:00:08"
nvram set emf_uffp_entry=""
nvram set bt_peer_limit_global="400"
nvram set qosl_tcp="0"
nvram set bt_ul_queue_enable="0"
nvram set wl1_radio_pwrsave_pps="10"
nvram set wl1_nreqd="0"
nvram set wl_dfs_preism="60"
nvram set wl0_radio_pwrsave_quiet_time="1800"
nvram set ppp_mlppp="0"
nvram set wl_sta_retry_time="5"
nvram set pptp_client_passwd=""
nvram set pci/2/1/mcs32po="0x2222"
nvram set wl_closed="0"
nvram set wl0_auth_mode="none"
nvram set wl_wme_txp_bk="7 3 4 2 0"
nvram set tm_tz="CET-1CEST,M3.5.0/2,M10.5.0/3"
nvram set udpxy_port="4022"
nvram set NC_AllowedWebHosts=""
nvram set pci/2/1/temps_hysteresis="5"
nvram set dhcpd3_endip=""
nvram set wl0_radio_pwrsave_enable="0"
nvram set bt_dir="/mnt"
nvram set wl1_wme_sta_vo="3 7 2 3264 1504 off off"
nvram set wl0.6_hwaddr="22:CF:30:B7:00:0E"
nvram set boardnum="00"
nvram set wl0_crypto="aes"
nvram set telnetd_port="23"
nvram set cstats_sshut="1"
nvram set snmp_port="161"
nvram set wl1_wds=""
nvram set wl0_txchain="7"
nvram set vpn_server2_reneg="-1"
nvram set bt_blocklist="1"
nvram set wl1.6_hwaddr="22:CF:30:B7:00:02"
nvram set wl1_vlan_prio_mode="off"
nvram set dnscrypt_proxy=""
nvram set wl_bcn="100"
nvram set snmp_contact="admin@tomato"
nvram set vpn_server1_cipher="default"
nvram set vpn_server1_dhcp="1"
nvram set wl1_wds_timeout="1"
nvram set pci/2/1/tssipos5g="1"
nvram set wl_wep_buf=""
nvram set wl_reg_mode="off"
nvram set upnp_secure="1"
nvram set upnp_mnp="1"
nvram set t_hidelr="0"
nvram set vpn_server_dns=""
nvram set bt_message="0"
nvram set cstats_enable="1"
nvram set vpn_client1_local="10.8.0.2"
nvram set pci/1/1/mcsbw202gpo="0xFC955555"
nvram set vpn_client2_retry="30"
nvram set wl_antdiv="-1"
nvram set ct_udp_timeout="30 180"
nvram set log_remoteip=""
nvram set idle_enable="0"
nvram set vpn_server1_port="1194"
nvram set pptp_client_mruenable="0"
nvram set bt_dl="248"
zyxeu
DD-WRT Novice


Joined: 29 Oct 2012
Posts: 13

PostPosted: Mon Dec 03, 2012 16:26    Post subject: Reply with quote
It looks like |bonza| has found the root cause: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=163479&start=375
|bonza| wrote:
1.0.1.3 CFE fails to init nvram variable "vlan1ports" which is needed by recovery mode.

hookup serial console
CFE >

nvram set vlan1ports="1 2 3 4 8*"
nvram commit

reboot and hold reset button to enter recovery
(192.168.1.1 is up and running again)
cloom
DD-WRT Novice


Joined: 09 Apr 2013
Posts: 1

PostPosted: Tue Apr 09, 2013 16:19    Post subject: Reply with quote
Hello, I am curious, you say you connect via serial to the router, how do you do that?
There is no serial port, do you use the USB ports or the RJ45 ones? First time I hear that.
hagkobe
DD-WRT Novice


Joined: 25 May 2013
Posts: 2

PostPosted: Sat May 25, 2013 15:46    Post subject: Reply with quote
After long searching i found on youtube the answer:

I finally got mine into recovery mode !!!!
ASUS RT-N66U

Had to hold down wps button, then power on, then once the router rebooted (all lights flash) let go of the wps button, and hold the reset button.
then the left blue light flash slowly.

This put it into recovery mode for me. Hope this helps.


grtz
kiamo
DD-WRT Novice


Joined: 22 Sep 2013
Posts: 11

PostPosted: Sun Sep 22, 2013 11:32    Post subject: Reply with quote
How did you get a serial interface up? I've followed the directions on

http://www.dd-wrt.com/wiki/index.php/Serial_Recovery

But I can't get putty to give me anything I can interact with. Please can you detail the steps you took?

When I don't have the serial connected I get ping timeouts and 4 LEDS on (power and eth 1/2, and the e planet thing)

When I have the serial connected and then I power on, the power LED does not come on. Not sure if that tells me anything important.

Thanks for any help everybody Smile
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum