[je1117]

I've set up the USB/NAT tabs correctly, but whenever I'm using my external HD plugged into the USB on my router - after about 5 minutes of usage, whether streaming video or copying files, the samba service hangs/stops. It then restarts/remounts in a new place.

/dev/scsi/host0/bus0/target0/lun0/part1 mounted to /tmp/mnt/disc0-part1

/dev/scsi/host1/bus0/target0/lun0/part1 mounted to /tmp/mnt/disc1-part1

/dev/scsi/host2/bus0/target0/lun0/part1 mounted to /tmp/mnt/disc2-part1

--- /dev/scsi/host0/bus0/target0/lun0/part1
Block device, size 465.8 GiB (500105249280 bytes)
Windows NTLDR boot loader
NTFS file system
UUID E8CC9DA1CC9D6B18
Volume size 465.8 GiB (500105248768 bytes, 976768064 sectors)
--- /dev/scsi/host1/bus0/target0/lun0/part1
Block device, size 465.8 GiB (500105249280 bytes)
Windows NTLDR boot loader
NTFS file system
UUID E8CC9DA1CC9D6B18
Volume size 465.8 GiB (500105248768 bytes, 976768064 sectors)
--- /dev/scsi/host2/bus0/target0/lun0/part1
Block device, size 465.8 GiB (500105249280 bytes)
Windows NTLDR boot loader
NTFS file system
UUID E8CC9DA1CC9D6B18
Volume size 465.8 GiB (500105248768 bytes, 976768064 sectors)

Feb 1 12:15:11 Linksys E4200v1 user.info syslog: smbd : samba successfully stopped
Feb 1 12:15:13 Linksys E4200v1 user.info syslog: smbd : samba hanging, send SIGKILL
Feb 1 12:15:13 Linksys E4200v1 user.info syslog: nmbd : nmbd successfully stopped
Feb 1 12:15:16 Linksys E4200v1 user.info syslog: nmbd : nmbd hanging, send SIGKILL
Feb 1 12:15:16 Linksys E4200v1 user.info syslog: Samba3 : samba started
Feb 1 12:18:12 Linksys E4200v1 auth.info login[15057]: root login on 'pts/0'
Feb 1 12:27:07 Linksys E4200v1 kern.info kernel: usb 1-1: USB disconnect, address 3
Feb 1 12:27:07 Linksys E4200v1 user.info syslog: cron : cron daemon successfully stopped
Feb 1 12:27:07 Linksys E4200v1 user.info syslog: smbd : samba successfully stopped
Feb 1 12:27:07 Linksys E4200v1 user.info syslog: nmbd : nmbd successfully stopped
Feb 1 12:27:08 Linksys E4200v1 cron.info cron[15388]: (CRON) STARTUP (fork ok)
Feb 1 12:27:08 Linksys E4200v1 user.info syslog: cron : cron daemon successfully started
Feb 1 12:27:08 Linksys E4200v1 cron.info cron[15388]: (crontabs) ORPHAN (no passwd entry)
Feb 1 12:27:10 Linksys E4200v1 user.info syslog: Samba3 : samba started
Feb 1 12:27:10 Linksys E4200v1 kern.info kernel: usb 1-1: new high speed USB device using ehci_hcd and address 4
Feb 1 12:27:10 Linksys E4200v1 kern.info kernel: usb 1-1: configuration #1 chosen from 1 choice
Feb 1 12:27:10 Linksys E4200v1 kern.info kernel: scsi2 : SCSI emulation for USB Mass Storage devices
Feb 1 12:27:12 Linksys E4200v1 kern.notice kernel: scsi 2:0:0:0: Direct-Access Seagate FreeAgent GoFlex 211 PQ: 0 ANSI: 0
Feb 1 12:27:12 Linksys E4200v1 kern.notice kernel: sd 2:0:0:0: [sdb] 976773167 512-byte hardware sectors (500108 MB)
Feb 1 12:27:12 Linksys E4200v1 kern.notice kernel: sd 2:0:0:0: [sdb] Write Protect is off
Feb 1 12:27:12 Linksys E4200v1 kern.debug kernel: sd 2:0:0:0: [sdb] Mode Sense: 0f 00 00 00
Feb 1 12:27:12 Linksys E4200v1 kern.err kernel: sd 2:0:0:0: [sdb] Assuming drive cache: write through
Feb 1 12:27:12 Linksys E4200v1 kern.err kernel: sd 2:0:0:0: [sdb] Assuming drive cache: write through
Feb 1 12:27:12 Linksys E4200v1 kern.info kernel: /dev/scsi/host2/bus0/target0/lun0: p1
Feb 1 12:27:12 Linksys E4200v1 kern.notice kernel: sd 2:0:0:0: [sdb] Attached SCSI disk
Feb 1 12:27:32 Linksys E4200v1 user.info syslog: cron : cron daemon successfully stopped
Feb 1 12:27:32 Linksys E4200v1 user.info syslog: smbd : samba successfully stopped
Feb 1 12:27:32 Linksys E4200v1 user.info syslog: nmbd : nmbd successfully stopped
Feb 1 12:27:35 Linksys E4200v1 cron.info cron[15468]: (CRON) STARTUP (fork ok)
Feb 1 12:27:35 Linksys E4200v1 cron.info cron[15468]: (crontabs) ORPHAN (no passwd entry)
Feb 1 12:27:35 Linksys E4200v1 user.info syslog: cron : cron daemon successfully started
Feb 1 12:27:35 Linksys E4200v1 user.info syslog: Samba3 : samba started

I've tried forcing it to mount in the same place using the UUID option in the USB tab, and I've also tried using startup script commands, but it never mounts where I tell it. Always goes to this /tmp/mnt/disc0-part1.

If I don't use it for more than a minute or 2, the service never stops.

Any feedback is appreciated.