[KidFrench]

Hello,

-Is that the mini pci cards are supported by ddwrt:

R52Hn AR9220
2SHPn AR9223

- I just tested the card R52Hn AR9220 on Avila ddwrt 2347, the card is not recognized, normal or not?

- Then I will soon take the RB800 in ddwrt activation, is-that these two cards (and R52Hn 2SHPn) will be supported?

- This is confusing to me because I thought all the cards were supported Atheros mini pci, are there exceptions?

[Sash]

upgrade and it will work

[KidFrench]

Hello,


Sash, I tested all upgrade with :


Avila 2347 + mini pci card 2SHPn (AR9223)


-Build : 14144, 14280,14311, 14896 and 20061 don't work


-Build : 12188 and 12533 work (the mini pci card is seen by avila 2347).


But the Tx-power=off :

lo no wireless extensions.
teql0 no wireless extensions.
wifi0 no wireless extensions.
ixp0 no wireless extensions.
ixp1 no wireless extensions.
br0 no wireless extensions.
etherip0 no wireless extensions.
bond0 no wireless extensions.
ath0 IEEE 802.11g ESSID:"dd-wrt"
Mode:Managed Channel:0 Access Point: Not-Associated
Bit Rate:0 kb/s Tx-Power=off Sensitivity=1/1
Retry:off RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/70 Signal level=-98 dBm Noise level=-98 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0


So, I try :

ifconfig ath0 down
iwconfig ath0 txpower auto
ifconfig ath0 up

But it does no work ...

Please, can you guide me ?

[Sash]

read:

[KidFrench]

@ Sash, it is not easy for me because I do not have much knowledge in this area.

I've read the wiki for several days and the various forum posts and elsewhere.

I tested different Build ...

But I do not find the answer to my problem

I went crazy and it makes me sick not find the answer (I'm serious) ...

Instead of telling me to go read the wiki (I've already done), rather it gives you more information to please guide me in the right direction

Now I wonder why I pay activations ddwrt ^ ^ because I can not use my material

[Sash]

just download the latest build from the beta folders

[KidFrench]

Hello,

Ok Sash;

I downloaded and I tested all the other files:

Downloads › others › eko › BrainSlayer-V24-preSP2 › 2013 › 07-24-2013-r22118 › gateworks_8M
Downloads › others › eko › BrainSlayer-V24-preSP2 › 2013 › 05-27-2013-r21676 › gateworks_8M
Downloads › others › eko › BrainSlayer-V24-preSP2 › 2013 › 04-15-2013-r21286 › gateworks_8M
Downloads › others › eko › BrainSlayer-V24-preSP2 › 2013 › 04-11-2013-r21223 › gateworks_8M
Downloads › others › eko › BrainSlayer-V24-preSP2 › 2013 › 04-01-2013-r21153 › gateworks_8M
Downloads › others › eko › BrainSlayer-V24-preSP2 › 2013 › 03-25-2013-r21061 › gateworks_8M
Downloads › others › eko › BrainSlayer-V24-preSP2 › 2013 › 02-11-2013-r20675 › gateworks_8M
Downloads › others › eko › BrainSlayer-V24-preSP2 › 2013 › 01-24-2013-r20548 › gateworks_8M
Downloads › others › eko › BrainSlayer-V24-preSP2 › 2012 › 10-12-12-r20119-testing › gateworks_8M


- None of these files have run the mini pci card R2SHPn (AR9223) on Avila Gateworks gw2347

- idem for builds : 21061, 14896, 14311, 14280, 14144, 13064, 12533, 12196, None of these builds are working ...

- when I insert the Mini PCI, led (card) is ok but I can not reach the dd-wrt administration :

-> not DHCP
-> disconnection repetitive LAN (computer)
-> computer message : cable not connected ... cable connected ... cable not connected ... etc ...


I changed my computer and cable even though I know that the problem is not there.


So, I tested the Mini PCI R2SHPn (AR9223) on another Routerboard, it works well.

what am I doing wrong for this mini pci card does not work?

Mini PCI mikrotik are not compatible DD-WRT ?

[Sash]

[KidFrench]

Hello Sash,

I connected the mini pci card R2SHPn AR9223 in Avila 2347.

Purpose there is no "WIRELESS" tab in the administration dd-wrt.

I entered the command: dmesg but no results

And


lspci -vv :


00:01.0 Network controller: Atheros Communications Inc. AR922X Wireless Network Adapter (rev 01)
Subsystem: Unknown device 19b6:d009
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-




iwconfig :

lo no wireless extensions.
teql0 no wireless extensions.
ixp0 no wireless extensions.
ixp1 no wireless extensions.
br0 no wireless extensions.
bond0 no wireless extensions.
etherip0 no wireless extensions.

[Sash]

do it from cli!

[KidFrench]

Hello Sash,

- Build : 14896

- Factory defaults : yes

- Plug mini pci card R2SHpn AR9223 in Avila 2347 (the blue led is ok)

- But no "WIRELESS" tab in the administration dd-wrt (I can access the dd-wrt administration when the card mini pci R2SHPn is inserted since I flashed with Redboot last 2 days).


dmesg :

root@DD-WRT:~# dmesg
[ 0.000000] Linux version 2.6.24.111 (root@dd-wrt) (gcc version 4.3.2 (GCC) ) #4869 Sat Aug 7 02:04:03 CEST 2010
[ 0.000000] CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE), cr=000039ff
[ 0.000000] Machine: Gateworks Avila Network Platform
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 8128 pages, LIFO batch:0
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
[ 0.000000] CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
[ 0.000000] Built 1 zonelists in Zone order. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,115200 panic=10 root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: 7, 512 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 32MB = 32MB total
[ 0.000000] Memory: 27668KB available (3740K code, 911K data, 104K init)
[ 0.000000] Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
[ 0.240000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] NET: Registered protocol family 16
[ 0.240000] init NPEB
[ 0.240000] init NPEC
[ 0.240000] IXP4xx: Using 16MiB expansion bus window size
[ 0.250000] Gateworks Model GW2347 detected!
[ 0.250000] PCI: IXP4xx is host
[ 0.250000] PCI: IXP4xx Using direct access for memory space
[ 0.250000] PCI: bus0: Fast back to back transfers enabled
[ 0.250000] dmabounce: registered device 0000:00:01.0 on pci bus
[ 0.270000] SCSI subsystem initialized
[ 0.270000] libata version 2.21 loaded.
[ 0.290000] NET: Registered protocol family 2
[ 0.300000] Time: OSTS clocksource has been installed.
[ 0.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.380000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.380000] TCP reno registered
[ 0.410000] devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
[ 0.410000] devfs: boot_options: 0x1
[ 0.410000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[ 0.410000] io scheduler noop registered
[ 0.410000] io scheduler deadline registered (default)
[ 0.930000] ixp425_gpio: IXP425 GPIO driver loaded
[ 0.930000] Serial: 8250/16550 driver $Revision: 1.90 $ 10 ports, IRQ sharing disabled
[ 0.950000] serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
[ 0.950000] console [ttyS0] enabled
[ 0.950000] serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
[ 0.960000] loop: module loaded
[ 0.960000] nbd: registered device at major 43
[ 0.980000] PPP generic driver version 2.4.2
[ 0.980000] PPP Deflate Compression module registered
[ 0.980000] PPP BSD Compression module registered
[ 0.980000] MPPE/MPPC encryption/compression module registered
[ 0.980000] NET: Registered protocol family 24
[ 0.980000] tun: Universal TUN/TAP device driver, 1.6
[ 0.980000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.980000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 0.980000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 0.980000] try to reserve 0x50000000 with size of 0x01000000
[ 0.980000] IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
[ 0.980000] IXP4XX-Flash.0: Found an alias at 0x800000 for the chip at 0x0
[ 0.980000] Intel/Sharp Extended Query Table at 0x0031
[ 0.980000] Using buffer write method
[ 0.980000] cfi_cmdset_0001: Erase suspend on write enabled
[ 0.980000] erase region 0: offset=0x0,size=0x20000,blocks=64
[ 0.980000] scanning for root partition
<0>[0x001C0000][0x00000000]
[ 1.010000] found squashfs/jffs2 at 1C0000
[ 1.010000] scan redboot from c37e0000
[ 1.010000] found RedBoot partition at [0x50000000]
[ 1.020000] found RedBoot config partition at [0x507FF000]
[ 1.020000] found config partition at [0x507E0000]
[ 1.030000] found linux partition at [0x50080000]
[ 1.030000] Creating 9 MTD partitions on "IXP4XX-Flash.0":
[ 1.030000] 0x00000000-0x00080000 : "RedBoot"
[ 1.030000] 0x00080000-0x007a0000 : "linux"
[ 1.030000] 0x001c0000-0x00760000 : "rootfs"
[ 1.030000] 0x00760000-0x007a0000 : "ddwrt"
[ 1.040000] 0x007a0000-0x007c0000 : "mampf"
[ 1.040000] 0x007c0000-0x007e0000 : "nvram"
[ 1.040000] 0x007e0000-0x00800000 : "FIS directory"
[ 1.040000] 0x007ff000-0x0081f000 : "RedBoot config"
[ 1.040000] mtd: partition "RedBoot config" extends beyond the end of device "IXP4XX-Flash.0" -- size truncated to 0x1000
[ 1.040000] mtd: partition "RedBoot config" doesn't start on an erase block boundary -- force read-only
[ 1.040000] 0x00000000-0x00800000 : "fullflash"
[ 1.040000] i2c /dev entries driver
[ 1.050000] ixp400: Module init.
[ 1.050000] Mirror/redirect action on
[ 1.050000] u32 classifier
[ 1.050000] Actions configured
[ 1.050000] Netfilter messages via NETLINK v0.30.
[ 1.050000] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 1.050000] ctnetlink v0.93: registering with nfnetlink.
[ 1.050000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.050000] IPP2P v0.8.2 loading
[ 1.050000] ipt_random match loaded
[ 1.060000] ClusterIP Version 0.8 loaded successfully
[ 1.060000] TCP bic registered
[ 1.060000] TCP cubic registered
[ 1.060000] TCP westwood registered
[ 1.060000] TCP highspeed registered
[ 1.060000] TCP hybla registered
[ 1.060000] TCP htcp registered
[ 1.060000] TCP vegas registered
[ 1.060000] TCP scalable registered
[ 1.060000] NET: Registered protocol family 1
[ 1.060000] NET: Registered protocol family 17
[ 1.060000] Welcome to PF_RING 3.2.1
[ 1.060000] (C) 2004-06 L.Deri <deri@ntop.org>
[ 1.060000] NET: Registered protocol family 27
[ 1.060000] PF_RING: bucket length 128 bytes
[ 1.060000] PF_RING: ring slots 4096
[ 1.060000] PF_RING: sample rate 1 [1=no sampling]
[ 1.060000] PF_RING: capture TX No [RX only]
[ 1.060000] PF_RING: transparent mode Yes
[ 1.060000] PF_RING initialized correctly.
[ 1.060000] PF_RING: registered /proc/net/pf_ring/
[ 1.060000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 1.060000] All bugs added by David S. Miller <davem@redhat.com>
[ 1.060000] XScale DSP coprocessor detected.
[ 1.080000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.100000] VFS: Mounted root (squashfs filesystem) readonly.
[ 1.120000] Mounted devfs on /dev
[ 1.120000] Freeing init memory: 104K
[ 8.370000] ath_hal: module license 'Proprietary' taints kernel.
[ 8.410000] ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, AR9160, AR9280, RF5111, RF5112, RF2413, RF5413, RF2425, XR)
[ 9.010000] ath_pci: svn r726
[ 9.010000] wlan: svn r726
[ 9.010000] wlan: mac acl policy registered
[ 9.020000] ath_rate_sample: 1.2 (svn r726)
[ 9.020000] ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (svn r726)
[ 9.030000] ath_rate_minstrel: look around rate set to 10%
[ 9.030000] ath_rate_minstrel: EWMA rolloff level set to 75%
[ 9.040000] ath_rate_minstrel: max segment size in the mrr set to 6000 us
[ 9.050000] CN: Idle Module registered
[ 9.050000] CN: Policy Module registered
[ 9.060000] CN: Polling Queue registered
[ 9.490000] ath_mimo_hal: 0.9.17.1 (AR5416, REGOPS_FUNC)
[ 10.220000] ath_mimo_pci: 0.9.4.5 (Atheros/multi-bss)
[ 10.220000] ath_mimo_pci: CR-LSDK-1.4.0.144
[ 10.230000] ath_dfs: Version 2.0.0
[ 10.230000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
[ 10.240000] wlan: 0.8.4.2 (Atheros/multi-bss)
[ 10.240000] wlan: mac acl policy registered
[ 10.250000] ath_rate_atheros: Version 2.0.1
[ 10.250000] Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved
[ 10.270000] PCI: enabling device 0000:00:01.0 (0340 -> 0342)
[ 10.280000] device id 29
[ 10.280000] wifi%d: unable to attach hardware; HAL status 14
[ 10.550000] ixp400_eth: Initializing IXP400 NPE Ethernet driver software v. 1.7
[ 10.560000] ixp400_eth: CPU clock speed (approx) = 266 MHz
[ 10.560000] init port 0, dev 0
[ 10.570000] [warning] ixNpeDlNpeMgrInit - Warning:NPEA is not present.
[ 10.580000] init port 1, dev 1
[ 14.410000] ixp400_eth: Found PHY 0 at address 0
[ 14.610000] ixp400_eth: ixp0 is using NPEB and the PHY at address 0
[ 14.640000] ixp400_eth: Use default MAC address 00:02:b3:01:01:01 for port 0
[ 14.680000] ixp400_eth: Use default MAC address 00:02:b3:02:02:02 for port 1
[ 15.030000] ixp400_eth:
[ 15.030000] ixp400_eth: ixp0 PHY:0 link up->down <4>ixp400_eth: ixEthMiiLinkStatus failed on PHY1.
[ 15.030000] Can't determine
[ 15.030000] the auto negotiated parameters. Using default values.
[ 15.370000] IXP4xx Watchdog Timer: heartbeat 60 sec
[ 18.320000] br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
[ 18.380000] device br0 entered promiscuous mode
[ 19.140000] device ixp0 entered promiscuous mode
[ 19.290000] device br0 left promiscuous mode
[ 19.300000] device br0 entered promiscuous mode
[ 19.320000] device br0 left promiscuous mode
[ 19.330000] device br0 entered promiscuous mode
[ 19.520000] ixp400_eth:
[ 19.520000] ixp400_eth: ixp0 PHY:0 link down->up <6>br0: port 1(ixp0) entering learning state
[ 19.770000] Ethernet Channel Bonding Driver: v3.1.3 (June 13, 2007)
[ 19.780000] bonding: MII link monitoring set to 100 ms
[ 20.530000] br0: topology change detected, propagating
[ 20.530000] br0: port 1(ixp0) entering forwarding state
[ 37.020000] etherip: Ethernet over IPv4 tunneling driver
root@DD-WRT:~#



lspci -vv :

root@DD-WRT:~# lspci -vv
00:01.0 Network controller: Atheros Communications Inc. AR922X Wireless Network Adapter (rev 01)
Subsystem: Unknown device 19b6:d009
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B+
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 28
Region 0: Memory at 48000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=100mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

[Sash]

the same again with the latest beta

[KidFrench]

Hello,

- I upgrade Build 14896 to Build 21061.

- After the upgrade, I can not insert any Mini PCI Atheros otherwise it is impossible for me to connect to the dd-wrt administration.

- I get this error on the LAN computer message : unconnected identification, connected cable, connected, identification, not connected, etc. ....

- So I do not plug any the mini pci wireless card so I can get to your dd-wrt:


- dmesg: (Build 21061)

root@DD-WRT:~# dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE), cr=000039ff
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Gateworks Avila Network Platform
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 803d9754, node_mem_map 80496000
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 8128 pages, LIFO batch:0
[ 0.000000] Linux version 3.8.4 (root@dd-wrt) (gcc version 4.7.3 20121106 (prerelease) (Linaro GCC 4.7-2012.11) ) #182 Mon Mar 25 02:39:19 CET 2013
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,115200 panic=10 root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Memory: 32MB = 32MB total
[ 0.000000] Memory: 27744k/27744k available, 5024k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0x82800000 - 0xff000000 (1992 MB)
[ 0.000000] lowmem : 0x80000000 - 0x82000000 ( 32 MB)
[ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
[ 0.000000] .text : 0x80008000 - 0x803983f4 (3649 kB)
[ 0.000000] .init : 0x80399000 - 0x803b22fc ( 101 kB)
[ 0.000000] .data : 0x803b4000 - 0x803dacc0 ( 156 kB)
[ 0.000000] .bss : 0x803dacc0 - 0x80495284 ( 746 kB)
[ 0.000000] NR_IRQS:32
[ 0.000000] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 64425ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000622] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.070107] pid_max: default: 32768 minimum: 301
[ 0.070426] Mount-cache hash table entries: 512
[ 0.071535] CPU: Testing write buffer coherency: ok
[ 0.072481] Setting up static identity map for 0x25c378 - 0x25c3c8
[ 0.074949] NET: Registered protocol family 16
[ 0.076806] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.078301] IXP4xx: Using 16MiB expansion bus window size
[ 0.080494] Gateworks Model GW2347 detected!
[ 0.081402] PCI: IXP4xx is host
[ 0.081436] PCI: IXP4xx Using direct access for memory space
[ 0.081715] PCI host bridge to bus 0000:00
[ 0.081774] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.081821] pci_bus 0000:00: root bus resource [mem 0x48000000-0x4bffffff]
[ 0.081862] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.082138] PCI: bus0: Fast back to back transfers enabled
[ 0.082190] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.090741] bio: create slab <bio-0> at 0
[ 0.091607] vgaarb: loaded
[ 0.093439] Switching to clocksource OSTS
[ 0.104685] NET: Registered protocol family 2
[ 0.106097] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.106177] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.106226] TCP: Hash tables configured (established 512 bind 512)
[ 0.106460] TCP: reno registered
[ 0.106498] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.106563] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.106990] NET: Registered protocol family 1
[ 0.107113] PCI: CLS 0 bytes, default 32
[ 0.110236] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[ 0.110301] msgmni has been set to 54
[ 0.114299] io scheduler noop registered
[ 0.114340] io scheduler deadline registered (default)
[ 0.192985] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 0.197453] serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
[ 0.534488] console [ttyS0] enabled
[ 0.539261] serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
[ 0.547092] ixp425_gpio: IXP425 GPIO driver loaded
[ 0.559374] loop: module loaded
[ 0.563254] nbd: registered device at major 43
[ 0.584268] try to reserve 0x50000000 with size of 0x01000000
[ 0.590780] IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x000017
[ 0.601070] IXP4XX-Flash.0: Found an alias at 0x800000 for the chip at 0x0
[ 0.601139] Intel/Sharp Extended Query Table at 0x0031
[ 0.606305] Intel/Sharp Extended Query Table at 0x0031
[ 0.611479] Using buffer write method
[ 0.615144] cfi_cmdset_0001: Erase suspend on write enabled
[ 0.620744] erase region 0: offset=0x0,size=0x20000,blocks=64
[ 0.620768] scanning for root partition
[ 0.624602] [0x00000000]
[0x00040000]3] [0x00020000]
[0x00080000]5] [0x00060000]
[0x000C0000]5] [0x000A0000]
[0x00100000]2] [0x000E0000]
[0x00140000]0] [0x00120000]
[0x00180000]7] [0x00160000]
[0x001C0000]5] [0x001A0000]
<0>[ 0.656014] 001E0000]
[ 0.656014] found squashfs/jffs2 at 1E0000
[ 0.661616] scan redboot from 837e0000
[ 0.665379] found RedBoot partition at [0x50000000]
[ 0.670311] found RedBoot config partition at [0x507FF000]
[ 0.675816] found config partition at [0x507E0000]
[ 0.680639] found linux partition at [0x50080000]
[ 0.685350] Creating 9 MTD partitions on "IXP4XX-Flash.0":
[ 0.690872] 0x000000000000-0x000000080000 : "RedBoot"
[ 0.697747] 0x000000080000-0x0000007a0000 : "linux"
[ 0.704497] 0x0000001e0000-0x0000007a0000 : "rootfs"
[ 0.711443] mtd: partition "rootfs" set to be root filesystem
[ 0.717233] 0x0000007a0000-0x000000800000 : "ddwrt"
[ 0.724079] 0x0000007a0000-0x0000007c0000 : "mampf"
[ 0.730936] 0x0000007c0000-0x0000007e0000 : "nvram"
[ 0.737382] 0x0000007e0000-0x000000800000 : "FIS directory"
[ 0.744664] 0x0000007ff000-0x00000081f000 : "RedBoot config"
[ 0.750428] mtd: partition "RedBoot config" extends beyond the end of device "IXP4XX-Flash.0" -- size truncated to 0x1000
[ 0.763025] 0x000000000000-0x000000800000 : "fullflash"
[ 0.770141] tun: Universal TUN/TAP device driver, 1.6
[ 0.775222] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.781670] PPP generic driver version 2.4.2
[ 0.786237] PPP BSD Compression module registered
[ 0.790992] PPP Deflate Compression module registered
[ 0.796094] PPP MPPE Compression module registered
[ 0.800909] NET: Registered protocol family 24
[ 0.805545] i2c /dev entries driver
[ 0.809198] install IXP4XX-I2C.0
[ 0.813228] rtc-ds1672 0-0068: chip found, driver version 0.4
[ 0.820220] rtc-ds1672 0-0068: ds1672_get_datetime: read error
[ 0.826451] rtc-ds1672 0-0068: rtc core: registered rtc-ds1672 as rtc0
[ 0.834082] rtc-ds1672 0-0068: ds1672_get_control: read error
[ 0.840031] rtc-ds1672: probe of 0-0068 failed with error -5
[ 0.846778] at24 0-0051: 1024 byte 24c08 EEPROM, read-only, 0 bytes/write
[ 0.857871] ixp4xx_wdt: timer heartbeat 60 sec
[ 0.862549] ixp400: Module init.
[ 0.864125] netem: version 1.3
[ 0.867208] u32 classifier
[ 0.869914] Performance counters on
[ 0.873827] input device check on
[ 0.877491] Actions configured
[ 0.880918] Netfilter messages via NETLINK v0.30.
[ 0.885813] nf_conntrack version 0.5.0 (433 buckets, 1732 max)
[ 0.892201] nf_conntrack_rtsp v0.6.21 loading
[ 0.898165] nf_nat_rtsp v0.6.21 loading
[ 0.902157] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.907946] IPP2P v0.8.2 loading
[ 0.911271] TCP: bic registered
[ 0.914416] TCP: cubic registered
[ 0.917736] TCP: westwood registered
[ 0.921326] TCP: highspeed registered
[ 0.924991] TCP: hybla registered
[ 0.928307] TCP: htcp registered
[ 0.931550] TCP: vegas registered
[ 0.934868] TCP: veno registered
[ 0.938096] TCP: scalable registered
[ 0.941686] TCP: lp registered
[ 0.944745] TCP: yeah registered
[ 0.947974] TCP: illinois registered
[ 0.951571] NET: Registered protocol family 17
[ 0.956307] Bridge firewalling registered
[ 0.960415] 8021q: 802.1Q VLAN Support v1.8
[ 0.964823] XScale DSP coprocessor detected.
[ 0.970496] searching for nvram
[ 0.973683] nvram size = -2144007330
[ 1.005283] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.020364] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.028060] Freeing init memory: 100K
[ 11.065272] ixp400_eth: Initializing IXP400 NPE Ethernet driver software v. 1.7
[ 11.072776] ixp400_eth: CPU clock speed (approx) = 265 MHz
[ 11.078488] init port 0, dev 0
[ 11.081584] [warning] ixNpeDlNpeMgrInit - Warning:NPEA is not present.
[ 11.091148] init port 1, dev 1
[ 14.910121] ixp400_eth: Found PHY 0 at address 0
[ 15.110122] ixp400_eth: ixp0 is using NPEB and the PHY at address 0
[ 15.121878] ixp400_eth: Use default MAC address 00:02:b3:01:01:01 for port 0
[ 15.151901] ixp400_eth: Use default MAC address 00:02:b3:02:02:02 for port 1
[ 15.477547] ixp400_eth: ixEthMiiLinkStatus failed on PHY1.
[ 15.477547] Can't determine
[ 15.477547] the auto negotiated parameters. Using default values.
[ 15.493423] ocf: module license 'BSD' taints kernel.
[ 15.498428] Disabling lock debugging due to kernel taint
[ 15.667379] ad7418 0-0028: ad7418 chip found
[ 15.673975] ad7418 0-0028: cannot read configuration register
[ 19.959990] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
[ 15.471682] ixp400_eth:
[ 15.471682] ixp400_eth: ixp0 PHY:0 link up->down
[ 20.364151] device ixp0 entered promiscuous mode
[ 20.756165] br0: port 1(ixp0) entered forwarding state
[ 20.761425] br0: port 1(ixp0) entered forwarding state
[ 22.760134] br0: port 1(ixp0) entered forwarding state
[ 43.982771] etherip: Ethernet over IPv4 tunneling driver
root@DD-WRT:~#


- lspci -vv:

(impossible because wireless cards are not supported on the Build 21061).


- So I returned to Build 14896 and I use Ubiquiti XR2, works well.

- But when I try this damn mikrotik mini pci card, no "wireless" tab in the administration dd-wrt, it's really strange yet it is a Atheros chipset ...

[Sash]

use an serial cable for logging and try again

[KidFrench]

Hello,

- I'll order and solder a male db9 connector because this connector is not originally present on the board at the location gateworks 2347 SERIAL PORT 1 (J5)
This will be cheaper and easier -> 1.05 euros.

- As soon as I finished, I will give the results.