Actiontec MI424WR can it be supported?

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> ARM or PPC based Hardware
Goto page 1, 2, 3 ... 35, 36, 37  Next
Author Message
rtoledo
DD-WRT User


Joined: 18 Mar 2007
Posts: 99

PostPosted: Sun Nov 25, 2007 23:07    Post subject: Actiontec MI424WR can it be supported? Reply with quote
by MOD
DONATIONS:
    -05dyna $50
    -HeXeD $20
    -Pow $20
    -oldtechgeek $20



Hi Brainslayer do you think this modem can be supported by ANY firmware writer such as yourself? it runs Linux and Jungo will supply the code for 15.00us. THANK YOU for your valuable time. so far there are only 2 versions of this modem and they come with both either a Ralink or an Atheros mini-pci card.

here is some info from another source / forum


/ # cat /proc/cpuinfo
Processor : XScale-IXP4xx/IXC11xx rev 1 (v5b)
BogoMIPS : 532.48
Features : swp half thumb fastmult edsp

Hardware : MI424-WR
Revision : 0000
Serial : 0000000000000000

/ # cat /proc/meminfo
total: used: free: shared: buffers: cached:
Mem: 29573120 16117760 13455360 0 0 4902912
Swap: 0 0 0
MemTotal: 28880 kB
MemFree: 13140 kB
MemShared: 0 kB
Buffers: 0 kB
Cached: 4788 kB
SwapCached: 0 kB
Active: 1172 kB
Inactive: 6956 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 28880 kB
LowFree: 13136 kB
SwapTotal: 0 kB
SwapFree: 0 kB

/ # ps
PID Uid Gid State Command
1 0 0 S init
2 0 0 S [keventd]
3 0 0 S [ksoftirqd_CPU0]
4 0 0 S [kswapd]
5 0 0 S [bdflush]
6 0 0 S [kupdated]
7 0 0 S [mtdblockd]
8 0 0 S /bin/openrg
16 0 0 S [ixp425_eth]
44 0 0 S [clink0_maint]
45 0 0 S [clink1_maint]
48 0 0 S /bin/sh
53 0 0 R ps

/ # cat /proc/pci
PCI devices found:
Bus 0, device 0, function 0:
Co-processor: PCI device 8086:8500 (Intel Corp.) (rev 1).
Prefetchable 32 bit memory at 0x0 [0xffffff].
Prefetchable 32 bit memory at 0x1000000 [0x1ffffff].
Prefetchable 32 bit memory at 0x2000000 [0x2ffffff].
Prefetchable 32 bit memory at 0x3000000 [0x3ffffff].
Prefetchable 32 bit memory at 0xff000000 [0xffffffff].
I/O at 0xffffff00 [0xffffffff].
Bus 0, device 13, function 0:
Ethernet controller: PCI device 17e6:0010 (rev 1).
IRQ 25.
Master Capable. Latency=16. Min Gnt=2.Max Lat=1.
Prefetchable 32 bit memory at 0x4bfc0000 [0x4bffffff].
Bus 0, device 13, function 1:
Multimedia controller: PCI device 17e6:0011 (rev 1).
IRQ 23.
Master Capable. Latency=16.
Prefetchable 32 bit memory at 0x4bfbf000 [0x4bfbffff].
Bus 0, device 14, function 0:
Network controller: PCI device 1814:0201 (rev 1).
IRQ 24.
Master Capable. Latency=16.
Non-prefetchable 32 bit memory at 0x4bfbc000 [0x4bfbdfff].
Bus 0, device 15, function 0:
Ethernet controller: PCI device 17e6:0010 (rev 1).
IRQ 23.
Master Capable. Latency=16. Min Gnt=2.Max Lat=1.
Prefetchable 32 bit memory at 0x4bf40000 [0x4bf7ffff].
Bus 0, device 15, function 1:
Multimedia controller: PCI device 17e6:0011 (rev 1).
IRQ 24.
Master Capable. Latency=16.
Prefetchable 32 bit memory at 0x4bf3f000 [0x4bf3ffff].

/ # df
Filesystem 1k-blocks Used Available Use% Mounted on
rootfs 13364 12 13352 0% /
tmpfs 13364 12 13352 0% /
cramfs 1596 1596 0 100% /mnt/cramfs
modfs 13364 12 13352 0% /mnt/modfs

/bin # cat /proc/cmdline
console=ttyS0,115200 root=/dev/ram0 rw nohalt


HERE IS MORE


A little more info:
/ # cat /proc/mtd
dev: size erasesize name
mtd0: 00800000 00020000 "openrg"

/ # lsmod
Module Size Used by
clnkdrv 189200 2
ks8995m_mod 6764 0 (unused)
qos_ingress 500 0 (unused)
btn 2036 0 (unused)
ppp 30520 0 (unused)
pppoe_relay 88504 0 (unused)
wlan_ccmp 5480 0
aes_mod 29364 0
crypto_mod 7376 0 [wlan_ccmp aes_mod]
wlan_acl 2380 1
wlan_tkip 9836 3
ath_pci 72244 1
ath_rate_atheros 25296 0 [ath_pci]
ath_hal 199592 1 [ath_pci ath_rate_atheros]
wlan_scan_ap 3532 1
wlan_xauth 516 0 (unused)
wlan_wep 4300 0
wlan 132744 1 [wlan_ccmp wlan_acl wlan_tkip ath_pci ath_rate_atheros wlan_scan_ap wlan_xauth wlan_wep]
krgldr_module 1100 0 (unused)
rg_ipv4 724 0 (unused)
rg_dhcp_pktfil 3156 0 (unused)
jfw 333484 0 (unused)
frag_cache_mod 6080 0 [jfw]
tcp_mss 1260 0 (unused)
rg_bridge 25168 1 [ks8995m_mod]
igmp_proxy_mod 5900 1
ixp425_eth_mod 9776 1
ixp425_csr_init_mod 1260 0 (unused)
csr 127088 0 [ixp425_eth_mod ixp425_csr_init_mod]
log_chardev 7068 0 [ks8995m_mod ppp pppoe_relay jfw frag_cache_mod rg_bridge]
kleds_mod 2332 0 (unused)
ixp425_flash_mod 1408 1
kos_lib 50704 4 [ks8995m_mod qos_ingress btn ppp pppoe_relay krgldr_module rg_ipv4 rg_dhcp_pktfil jfw frag_cache_mod tcp_mss rg_bridge igmp_proxy_mod ixp425_eth_mod log_chardev kleds_mod]

_________________
_________________
It's raining but it's time to go ride Othar! you only live once if you do it right
http://antwrp.gsfc.nasa.gov/apod/archivepix.html
_________________
Sponsor
SirSilentBob
DD-WRT User


Joined: 09 Oct 2007
Posts: 155

PostPosted: Tue Nov 27, 2007 4:35    Post subject: Reply with quote
Yes it would be nice, so many people with fios are stuck with that piece of shit!
I am lucky, I got my FIOS service just before they went to the new policy of not enabling ethernet for new installs. If I would have ended up being stuck with that actiontech, I would have canceled my 30 meg service and went back to my shitty 5 meg service with Cox. Thank God for DDWRT and a WHR-G125!!!!!!!!
rtoledo
DD-WRT User


Joined: 18 Mar 2007
Posts: 99

PostPosted: Wed Nov 28, 2007 2:09    Post subject: Reply with quote
SirSilentBob wrote:
Yes it would be nice, so many people with fios are stuck with that piece of shit!
I am lucky, I got my FIOS service just before they went to the new policy of not enabling ethernet for new installs. If I would have ended up being stuck with that actiontech, I would have canceled my 30 meg service and went back to my shitty 5 meg service with Cox. Thank God for DDWRT and a WHR-G125!!!!!!!!


I hope you are wrong I've read inDSLreports.com fios forum that they will enable the ethernet, i called and asked to have that on or no deal


UPDATE:I had FIOS service installed 2 weeks ago and the TECH showed me how they turn on the ethernet port from their laptop. so mine is on ethernet, I will let you know when I get TV service in February if anything changes in relation to ethernet, but some people that have it say they still have the ethernet port active. so I will let you know.


Last edited by rtoledo on Sat Dec 15, 2007 18:16; edited 1 time in total
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17473
Location: Hesse/Germany

PostPosted: Sat Dec 15, 2007 10:11    Post subject: Reply with quote
it should be posible to run dd-wrt.

has it redboot bootloader?

u have to contact brainslayer for support.

_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
rtoledo
DD-WRT User


Joined: 18 Mar 2007
Posts: 99

PostPosted: Sat Dec 15, 2007 18:20    Post subject: need commands to see if it has redboot Reply with quote
Sash wrote:
it should be posible to run dd-wrt.

has it redboot bootloader?

u have to contact brainslayer for support.


I don't know.
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17473
Location: Hesse/Germany

PostPosted: Sun Dec 16, 2007 11:10    Post subject: Reply with quote
then u have to find it out.

redboot is nessecary for useing ddwrt. read the specs or ask the vendor.

_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
theg33kb0y
DD-WRT Novice


Joined: 07 Jan 2008
Posts: 4

PostPosted: Mon Jan 07, 2008 2:59    Post subject: Reply with quote
bump. This is also a cross-post from here: http://forum.openwrt.org/viewtopic.php?pid=61342 which has more information and unit images on the same subject.

I have a MI424WR and just updated to Verizon's latest MI424WR firmware here: http://www2.verizon.net/micro/actiontec/actiontec.asp . The new firmware has more utilities built into the flash and a bit more information about how-it-works. I find the console=ttyS0,115200 particularly interesting. I remember hearing someone express that it has a serial plug on the board. I've not plugged in, but it might give pre-kernel debug output.

It would be nice to get support for NFS or CIFS or something to mount external filesystems with more goodies on it, perhaps a full-blown XScale distro (if such a thing exists).

The processor is an IXP4xx, which is supported by OpenWRT for devices such as Gateway 7001, and FreecomFSG3.

Since its a simple RT2500 chip and we already have XScale 42x support, I would think this trivial if Kendin switch/ethernet is supported. We just need to figure out how to package the firmware for update...

More details below. Ideas ... ?

-geek

No dmesg, but /proc/kmsg gives reasonable results:
/proc/kmsg
Code:
/ # cat /proc/kmsg
<4>Linux version 2.4.21openrg-rmk1 #2 Wed Nov 14 16:37:02 EST 2007
<4>CPU: XScale-IXP4xx/IXC11xx revision 1
<4>Machine: MI424-WR
<4>On node 0 totalpages: 8192
<4>zone(0): 8192 pages.
<4>zone(1): 0 pages.
<4>zone(2): 0 pages.
<4>Kernel command line: console=ttyS0,115200 root=/dev/ram0 rw nohalt
<7>Relocating machine vectors to 0xffff0000
<4>Using IXP425 Timer 0 as timer source
<4>Calibrating delay loop... 532.48 BogoMIPS
<6>Memory: 32MB = 32MB total
<5>Memory: 26476KB available (901K code, 4777K data, 224K init)
<6>XScale Cache/TLB Locking Copyright(c) 2001 MontaVista Software, Inc.
<6>Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
<6>Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
<6>Mount cache hash table entries: 512 (order: 0, 4096 bytes)
<4>Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
<4>Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
<4>POSIX conformance testing by UNIFIX
<6>PCI: bus0: Fast back to back transfers disabled
<4>PCI: 13.1: PCI device 17e6:0010 got irq 25
<4>PCI: 13.2: PCI device 17e6:0011 got irq 23
<4>PCI: 14.1: PCI device 1814:0201 got irq 24
<4>PCI: 15.1: PCI device 17e6:0010 got irq 23
<4>PCI: 15.2: PCI device 17e6:0011 got irq 24
<6>Linux NET4.0 for Linux 2.4
<6>Based upon Swansea University Computer Society NET3.039
<4>Initializing RT netlink socket
<4>Starting kswapd
<4>
<4>Random: 0x146acda8
<4>pty: 256 Unix98 ptys configured
<6>Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
<6>ttyS00 at 0xff000003 (irq = 15) is a XScale UART
<6>ttyS01 at 0xff001003 (irq = 13) is a XScale UART
<6>NET4: Linux TCP/IP 1.0 for NET4.0
<6>IP Protocols: ICMP, UDP, TCP, IGMP
<6>IP: routing cache hash table of 512 buckets, 4Kbytes
<6>TCP: Hash tables configured (established 2048 bind 4096)
<6>NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
<1>802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
<1>All bugs added by David S. Miller <davem@redhat.com>
<4>VFS: Mounted root (tmpfs filesystem).
<4>Mount of initial cramfs successful
<6>Freeing init cramfs memory: 64K
<6>Freeing init memory: 224K
<4>Mounting cramfs image at 'cramfs'
<4>loading license key: Actiontec License
<5>cfi_cmdset_0001: Erase suspend on write enabled
<7>0: offset=0x0,size=0x20000,blocks=64
<4>Using buffer write method
<4>Using predefined MTD partitions.
<5>Creating 1 MTD partitions on "IXP425 Flash Bank 0":
<5>0x00000000-0x00800000 : "openrg"
<4>Module init.
<4>Intel CSR QMGR & NPE(s) init done.
<4>Initializing ixp425_eth driver 0.0.8
<4>Found PHY 0 at 1
<4>Found PHY 1 at 2
<4>Found PHY 2 at 3
<4>Found PHY 3 at 4
<4>Found PHY 4 at 5
<4>Found PHY 5 at 17
<4>PHY 0 MAC address is:        04:04:04:04:04:04
<4>PHY 1 MAC address is:        06:06:06:06:06:06
<4>IPV4 device driver registered
<6>wlan: 0.8.4.2 (Atheros/multi-bss)
<6>ath_hal: 0.9.17.1 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413, REGOPS_FUNC)
<6>ath_rate_atheros: Version 2.0.1
<4>Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved
<6>ath_pci: 0.9.4.5 (Atheros/multi-bss)
<6>wlan: mac acl policy registered
<4>Kendin HW Switch: VLAN Group 15 used for default VLAN 0
<4>Kendin HW Switch: PVID of all ports set to 0
<4>Kendin HW Switch: Configured as VLAN Switch
<4>Kendin ID: 95:07
<4>Kendin port 1 status: ff
<4>Kendin port 2 status: 00
<4>Kendin port 3 status: 80
<4>Kendin port 4 status: 80
<4>Kendin port 5 status: 00
<5>Linux Clink Ethernet driver version 2.33.0.0 (Mar.3, 2006)
<6>Freeing modfs memory: 2052K
<7>Clink Link Down (freq timer)
<7>Clink Link Down (freq timer)
<4>PHY 1 MAC address is:        00:18:01:20:fa:65
<4>PHY 1 MAC address is:        00:18:01:20:fa:65
<4>ixp1: Entering promiscuous mode
<6>device ixp1 entered promiscuous mode
<4>SWITCH LOGIC reset 0
<4>Bridge Managed Ports: 4
<4>STP: ixp1/0 enters blocking mode
<4>STP: ixp1/1 enters blocking mode
<4>STP: ixp1/2 enters blocking mode
<4>STP: ixp1/3 enters blocking mode
<7>Clink Link Down (freq timer)
<7>Clink Link Down (freq timer)
<6>device ra0 entered promiscuous mode
<4>Bridge Managed Ports: 1
<4>STP: ra0 enters blocking mode
<4>Bridge Managed Ports: 4
<4>STP: ixp1/0 enters blocking mode
<4>STP: ixp1/1 enters blocking mode
<4>STP: ixp1/2 enters blocking mode
<4>STP: ixp1/3 enters blocking mode
<4>STP: ixp1/3 exits blocking mode
<4>STP: ixp1/2 exits blocking mode
<4>STP: ixp1/1 exits blocking mode
<4>STP: ixp1/0 exits blocking mode
<4>STP: ra0 exits blocking mode

Loaded modules:
lsmod
Code:
/ # lsmod
Module                  Size  Used by
clnkdrv               187880   0 (unused)
ks8995m_mod             6944   0 (unused)
qos_ingress              500   0 (unused)
btn                     2036   0 (unused)
ppp                    30196   0 (unused)
wlan_ccmp               5480   0 (unused)
aes_mod                29364   0 (unused)
crypto_mod              7376   0 [wlan_ccmp aes_mod]
wlan_acl                2380   0 (unused)
wlan_tkip               9836   0 (unused)
ath_pci                72244   0 (unused)
ath_rate_atheros       25296   0 [ath_pci]
ath_hal               199592   0 [ath_pci ath_rate_atheros]
wlan_scan_ap            3532   0 (unused)
wlan_xauth               516   0 (unused)
wlan_wep                4300   0 (unused)
wlan                  132968   0 [wlan_ccmp wlan_acl wlan_tkip ath_pci ath_rate_atheros wlan_scan_ap wlan_xauth wlan_wep]
rt2560                222328   1
krgldr_module           1100   0 (unused)
rg_ipv4                  724   0 (unused)
rg_dhcp_pktfil          3156   0 (unused)
jfw                   333440   0 (unused)
frag_cache_mod          6068   0 [jfw]
tcp_mss                 1260   0 (unused)
rg_bridge              25188   1 [ks8995m_mod]
igmp_proxy_mod          5900   1
ixp425_eth_mod         10028   1
ixp425_csr_init_mod     1260   0 (unused)
csr                   127088   0 [ixp425_eth_mod ixp425_csr_init_mod]
log_chardev             1868   0 (unused)
act_kconf_mod            316   0 [ixp425_eth_mod]
kleds_mod               2356   0 (unused)
ixp425_flash_mod        1408   1
kos_lib                57432   2 [ks8995m_mod qos_ingress btn ppp krgldr_module rg_ipv4 rg_dhcp_pktfil jfw frag_cache_mod tcp_mss rg_bridge igmp_proxy_mod ixp425_eth_mod log_chardev kleds_mod]

/proc # cat iomem
Code:
00000000-01ffffff : System RAM
  00040000-00121513 : Kernel code
  00121514-005cbd03 : Kernel data
4bf40000-4bf7ffff : clnk_eth
4bfbc000-4bfbdfff : 00:0e.0
4bfc0000-4bffffff : clnk_eth
50000000-507fffff : IXP425 Flash Bank 0

/ # cat /proc/cpuinfo
Code:
Processor       : XScale-IXP4xx/IXC11xx rev 1 (v5b)
BogoMIPS        : 532.48
Features        : swp half thumb fastmult edsp

Hardware        : MI424-WR
Revision        : 0000
Serial          : 0000000000000000

supported devices & filesystems
Code:
/proc # cat devices
Character devices:
  1 mem
  2 pty
  3 ttyp
  4 ttyS
  5 cua
 10 misc
 36 netlink
128 ptm
136 pts
162 raw
240 rg_chrdev

Block devices:
 31 mtdblock
/proc # cat filesystems
nodev   rootfs
nodev   bdev
nodev   proc
nodev   sockfs
nodev   tmpfs
nodev   shm
nodev   pipefs
nodev   cramfs
nodev   ramfs
        romfs
nodev   modfs
/proc #
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17473
Location: Hesse/Germany

PostPosted: Mon Jan 07, 2008 11:23    Post subject: Reply with quote
i spoke to BS and he needs the devices on his desk to add support for them Exclamation akaif this is caused on the complicated reconstruction of some onboard (flash) vendor information.

i will send him some tonze devices the next days.
so plz contact him and send him a sample device.

_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
theg33kb0y
DD-WRT Novice


Joined: 07 Jan 2008
Posts: 4

PostPosted: Mon Jan 07, 2008 23:28    Post subject: Needs hardware? Reply with quote
I can loan my unit to the cause if I can be guaranteed to get it back. Can you have him contact me?
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17473
Location: Hesse/Germany

PostPosted: Tue Jan 08, 2008 10:48    Post subject: Reply with quote
we are not openwrt...u can can get your device back Cool
watch the memberlist at the top. he the first man in line.....why Question Wink
the only thin is that u have to ship it to germany. if you are outside th EU it is easier and cheaper if someone who is inside would provide a device.

_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
theg33kb0y
DD-WRT Novice


Joined: 07 Jan 2008
Posts: 4

PostPosted: Tue Jan 08, 2008 22:47    Post subject: Reply with quote
I'm going to wire into its serial port and see if it boots redboot. If it does, I might be able to do it and push you guys the diffs.
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17473
Location: Hesse/Germany

PostPosted: Wed Jan 09, 2008 0:00    Post subject: Reply with quote
plz contact brainslayer
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
zuzu
DD-WRT Novice


Joined: 18 Jan 2008
Posts: 14

PostPosted: Fri Jan 18, 2008 0:35    Post subject: Reply with quote
The Actiontec MI424WR runs BusyBox Linux already, although it is "locked down" and Verizon is currently being sued for not releasing their source code changes as the GPL requires.
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 6096
Location: Dresden, Germany

PostPosted: Sat Jan 19, 2008 22:09    Post subject: Reply with quote
this router sounds promising. i will take care of it as soon as i get one.
_________________
one cigarette costs 2 minutes of your life.
one bottle of beer costs 4 minutes of your life.
one working day costs 8 hours of your life.

DD-WRT supported Concerts @ Bunker Dresden
03.10.2014 - Front 242 / Haujobb / Planet Myer Day
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17473
Location: Hesse/Germany

PostPosted: Sat Jan 19, 2008 23:18    Post subject: Reply with quote
hi sebi,

maybe rtoledo or theg33kb0y will send u his device?

ps: schau mal bitte in deine pm´s. ich hab dir den tonze geschickt. ist er angekommen?

edit:
it would be nice if someone could add further infos here http://www.dd-wrt.com/wiki/index.php/Supported_Devices#Actiontec

more edit:
the wlan is b/g an ralink based which is not supported rigth now. so it must be replaced be a atheros card. the cable port will not work i think.

maybe this is the fcc-id: p1mi424wr50508

i found some useful info here:
http://www.smallnetbuilder.com/content/view/30022/51/

here are pics of the pcb.

_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
Goto page 1, 2, 3 ... 35, 36, 37  Next Display posts from previous:    Page 1 of 37
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> ARM or PPC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum