user3160
DD-WRT Novice
Joined: 29 Dec 2013
Posts: 3
|
 Posted: Fri Jan 03, 2014 13:24 Post subject: TPLINK WDR3600 не подключается по 3g |
 |
Постил вопрос в англоязычном форуме в общей теме, но за неделю ни одного ответа, может местные гуру помогут понять в чем дело?
У меня USB 3g модем Alcatel X520 3g. Не получается подключиться к инету, при нажатии 'connect' во вкладке Status -> WAN ничего не происходит.
DD-WRT версия: DD-WRT v24-sp2 (03/25/13) std
Что я делаю не так?
cat /proc/bus/usb/devices output:
| Code: | T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.05
S: Manufacturer=Linux 3.5.7 ehci_hcd
S: Product=Atheros AR91xx built-in EHCI controller
S: SerialNumber=platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=05e3 ProdID=0608 Rev=85.36
S: Product=USB2.0 Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bbb ProdID=f000 Rev= 0.00
S: Manufacturer=USBModem
S: Product=HSPA Data Card
S: SerialNumber=1234567890ABCDEF
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms |
dmesg output:
| Code: | <6>[ 0.820000] console [ttyS0] enabled
<0>[ 0.830000] guessed flashsize = 8M
<0>[ 0.830000] scanning for root partition
<0>[ 0.840000] tplink uboot detected
<0>[ 0.840000] guessed bootloader size = 20000
<0>[ 0.850000]
<0>[ 0.850000] found squashfs at 130000
<5>[ 0.850000] Creating 8 MTD partitions on "ar7240-nor0":
<5>[ 0.860000] 0x000000000000-0x000000020000 : "RedBoot"
<5>[ 0.870000] 0x000000020000-0x0000007e0000 : "linux"
<5>[ 0.870000] 0x000000130000-0x0000007b0000 : "rootfs"
<5>[ 0.880000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.880000] 0x0000007b0000-0x0000007e0000 : "ddwrt"
<5>[ 0.890000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.900000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.900000] 0x000000000000-0x000000800000 : "fullflash"
<5>[ 0.910000] 0x000000000000-0x000000020000 : "fullboot"
<6>[ 0.920000] Fixed MDIO Bus: probed
<6>[ 0.920000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.930000] tun: (C) 1999-2004 Max Krasnyansky
<6>[ 0.930000] PPP generic driver version 2.4.2
<6>[ 0.940000] PPP BSD Compression module registered
<6>[ 0.940000] PPP Deflate Compression module registered
<6>[ 0.950000] PPP MPPE Compression module registered
<6>[ 0.950000] NET: Registered protocol family 24
<7>[ 0.960000] Registered led device: generic_0
<7>[ 0.960000] Registered led device: generic_1
<7>[ 0.960000] Registered led device: generic_2
<7>[ 0.960000] Registered led device: generic_3
<7>[ 0.960000] Registered led device: generic_4
<7>[ 0.960000] Registered led device: generic_5
<7>[ 0.960000] Registered led device: generic_6
<7>[ 0.960000] Registered led device: generic_7
<7>[ 0.960000] Registered led device: generic_8
<7>[ 0.960000] Registered led device: generic_9
<7>[ 0.960000] Registered led device: generic_10
<7>[ 0.960000] Registered led device: generic_11
<7>[ 0.960000] Registered led device: generic_12
<7>[ 0.960000] Registered led device: generic_13
<7>[ 0.960000] Registered led device: generic_14
<7>[ 0.960000] Registered led device: generic_15
<7>[ 0.960000] Registered led device: generic_16
<7>[ 0.960000] Registered led device: generic_17
<7>[ 0.960000] Registered led device: generic_18
<7>[ 0.960000] Registered led device: generic_19
<7>[ 0.960000] Registered led device: generic_20
<7>[ 0.960000] Registered led device: generic_21
<7>[ 0.960000] Registered led device: generic_22
<7>[ 0.960000] Registered led device: generic_23
<7>[ 0.960000] Registered led device: generic_24
<7>[ 0.960000] Registered led device: generic_25
<7>[ 0.960000] Registered led device: generic_26
<7>[ 0.960000] Registered led device: generic_27
<7>[ 0.960000] Registered led device: generic_28
<7>[ 0.960000] Registered led device: generic_29
<7>[ 0.960000] Registered led device: generic_30
<7>[ 0.960000] Registered led device: generic_31
<7>[ 0.970000] Registered led device: wireless_generic_0
<7>[ 0.970000] Registered led device: wireless_generic_1
<7>[ 0.970000] Registered led device: wireless_generic_2
<7>[ 0.970000] Registered led device: wireless_generic_3
<7>[ 0.970000] Registered led device: wireless_generic_4
<7>[ 0.970000] Registered led device: wireless_generic_5
<7>[ 0.970000] Registered led device: wireless_generic_6
<7>[ 0.970000] Registered led device: wireless_generic_7
<7>[ 0.970000] Registered led device: wireless_generic_8
<7>[ 0.970000] Registered led device: wireless_generic_9
<7>[ 0.970000] Registered led device: wireless_generic_10
<7>[ 0.970000] Registered led device: wireless_generic_11
<7>[ 0.970000] Registered led device: wireless_generic_12
<7>[ 0.970000] Registered led device: wireless_generic_13
<7>[ 0.970000] Registered led device: wireless_generic_14
<7>[ 0.970000] Registered led device: wireless_generic_15
<7>[ 0.970000] Registered led device: wireless_generic_16
<7>[ 0.970000] Registered led device: wireless_generic_17
<7>[ 0.970000] Registered led device: wireless_generic_18
<7>[ 0.970000] Registered led device: wireless_generic_19
<7>[ 0.970000] Registered led device: wireless_generic_20
<7>[ 0.970000] Registered led device: wireless_generic_21
<7>[ 0.970000] Registered led device: wireless_generic_22
<7>[ 0.970000] Registered led device: wireless_generic_23
<7>[ 0.970000] Registered led device: wireless_generic_24
<7>[ 0.970000] Registered led device: wireless_generic_25
<7>[ 0.970000] Registered led device: wireless_generic_26
<7>[ 0.970000] Registered led device: wireless_generic_27
<7>[ 0.970000] Registered led device: wireless_generic_28
<7>[ 0.970000] Registered led device: wireless_generic_29
<7>[ 0.970000] Registered led device: wireless_generic_30
<7>[ 0.970000] Registered led device: wireless_generic_31
<6>[ 0.970000] u32 classifier
<6>[ 0.980000] Performance counters on
<6>[ 0.980000] input device check on
<6>[ 0.980000] Actions configured
<6>[ 0.990000] Netfilter messages via NETLINK v0.30.
<6>[ 0.990000] nf_conntrack version 0.5.0 (1981 buckets, 7924 max)
<4>[ 1.000000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 1.000000] nf_nat_rtsp v0.6.21 loading
<6>[ 1.010000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 1.010000] IPP2P v0.8.2 loading
<6>[ 1.020000] TCP: westwood registered
<6>[ 1.020000] TCP: hybla registered
<6>[ 1.020000] TCP: vegas registered
<6>[ 1.030000] NET: Registered protocol family 17
<5>[ 1.030000] Bridge firewalling registered
<6>[ 1.040000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 1.040000] searching for nvram
<6>[ 1.040000] nvram size = 0
<6>[ 1.070000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 1.080000] ar71xx-wdt: timeout=15 secs (max=107) ref freq=40000000
<6>[ 1.090000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 1.100000] Freeing unused kernel memory: 168k freed
<7>[ 3.350000] ar71xx-wdt: enabling watchdog timer
<6>[ 3.520000] switch0: Atheros AR8327 switch registered on ag71xx-mdio.0
<6>[ 3.530000] ag71xx_mdio: probed
<6>[ 3.540000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
<6>[ 5.830000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
<6>[ 7.040000] Compat-drivers backport release: compat-drivers-2013-01-21-1
<6>[ 7.040000] Backport based on wireless-testing.git master-2013-02-22
<6>[ 7.050000] compat.git: wireless-testing.git
<6>[ 7.200000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 7.210000] cfg80211: World regulatory domain updated:
<6>[ 7.210000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 7.220000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 7.230000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 7.240000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 7.240000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 7.250000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<7>[ 7.790000] ath: EEPROM regdomain: 0x0
<7>[ 7.790000] ath: EEPROM indicates default country code should be used
<7>[ 7.790000] ath: doing EEPROM country->regdmn map search
<7>[ 7.790000] ath: country maps to regdmn code: 0x3a
<7>[ 7.790000] ath: Country alpha2 being used: US
<7>[ 7.790000] ath: Regpair used: 0x3a
<7>[ 7.800000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<7>[ 7.800000] Registered led device: ath9k-phy0
<6>[ 7.800000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=78
<7>[ 7.810000] ath: EEPROM regdomain: 0x0
<7>[ 7.810000] ath: EEPROM indicates default country code should be used
<7>[ 7.810000] ath: doing EEPROM country->regdmn map search
<7>[ 7.810000] ath: country maps to regdmn code: 0x3a
<7>[ 7.810000] ath: Country alpha2 being used: US
<7>[ 7.810000] ath: Regpair used: 0x3a
<7>[ 7.810000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
<7>[ 7.810000] Registered led device: ath9k-phy1
<6>[ 7.810000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=72
<6>[ 7.820000] cfg80211: Calling CRDA for country: US
<6>[ 7.830000] cfg80211: Regulatory domain changed to country: US
<6>[ 7.840000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 7.840000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 7.850000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 7.860000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 7.870000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 7.880000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 7.880000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<6>[ 7.890000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
<6>[ 8.310000] usbcore: registered new interface driver usbfs
<6>[ 8.310000] usbcore: registered new interface driver hub
<6>[ 8.320000] usbcore: registered new device driver usb
<6>[ 8.390000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 8.440000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 8.450000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<4>[ 8.460000] ehci_reset Intialize USB CONTROLLER in host mode: 13
<4>[ 8.460000] ehci_reset Port Status 1c000000
<6>[ 8.500000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 8.520000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 8.520000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 8.530000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 8.540000] usb usb1: Product: Atheros AR91xx built-in EHCI controller
<6>[ 8.540000] usb usb1: Manufacturer: Linux 3.5.7 ehci_hcd
<6>[ 8.550000] usb usb1: SerialNumber: platform
<6>[ 8.550000] hub 1-0:1.0: USB hub found
<6>[ 8.560000] hub 1-0:1.0: 1 port detected
<6>[ 8.860000] eth0: link up (1000Mbps/Full duplex)
<6>[ 8.880000] usb 1-1: new high-speed USB device number 2 using ar71xx-ehci
<6>[ 9.030000] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
<6>[ 9.030000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
<6>[ 9.040000] usb 1-1: Product: USB2.0 Hub
<6>[ 9.050000] hub 1-1:1.0: USB hub found
<6>[ 9.050000] hub 1-1:1.0: 4 ports detected
<6>[ 9.150000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
<4>[ 10.110000] lzma_compress: module license 'unspecified' taints kernel.
<4>[ 10.120000] Disabling lock debugging due to kernel taint
<6>[ 10.270000] jffs2: version 2.2. (NAND) (ZLIB) (LZMA) (RTIME) (CMODE_SIZE) © 2001-2006 Red Hat, Inc.
<3>[ 10.290000] jffs2: Too few erase blocks (3)
<6>[ 10.720000] device vlan1 entered promiscuous mode
<6>[ 10.720000] device eth0 entered promiscuous mode
<6>[ 10.760000] device vlan2 entered promiscuous mode
<6>[ 10.770000] br0: port 2(vlan2) entered forwarding state
<6>[ 10.780000] br0: port 2(vlan2) entered forwarding state
<6>[ 10.780000] br0: port 1(vlan1) entered forwarding state
<6>[ 10.790000] br0: port 1(vlan1) entered forwarding state
<6>[ 10.850000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 10.850000] cfg80211: World regulatory domain updated:
<6>[ 10.860000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 10.870000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.880000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.880000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.890000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.900000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.940000] cfg80211: Calling CRDA for country: US
<6>[ 10.940000] cfg80211: Regulatory domain changed to country: US
<6>[ 10.950000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 10.960000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 10.970000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 10.970000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.980000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 10.990000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 11.000000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<6>[ 11.010000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
<6>[ 11.820000] usb 1-1.1: new high-speed USB device number 3 using ar71xx-ehci
<6>[ 11.930000] usb 1-1.1: New USB device found, idVendor=1bbb, idProduct=f000
<6>[ 11.930000] usb 1-1.1: New USB device strings: Mfr=3, Product=2, SerialNumber=4
<6>[ 11.940000] usb 1-1.1: Product: HSPA Data Card
<6>[ 11.950000] usb 1-1.1: Manufacturer: USBModem
<6>[ 11.950000] usb 1-1.1: SerialNumber: 1234567890ABCDEF
<6>[ 12.780000] br0: port 2(vlan2) entered forwarding state
<6>[ 12.790000] br0: port 1(vlan1) entered forwarding state
<6>[ 14.020000] device ath0 entered promiscuous mode
<6>[ 14.290000] br0: port 3(ath0) entered forwarding state
<6>[ 14.300000] br0: port 3(ath0) entered forwarding state
<6>[ 16.300000] br0: port 3(ath0) entered forwarding state
<6>[ 19.080000] device ath1 entered promiscuous mode
<6>[ 19.340000] br0: port 4(ath1) entered forwarding state
<6>[ 19.350000] br0: port 4(ath1) entered forwarding state
<6>[ 21.090000] usbcore: registered new interface driver cdc_acm
<6>[ 21.100000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
<6>[ 21.210000] usbcore: registered new interface driver cdc_wdm
<6>[ 21.330000] usbcore: registered new interface driver qmi_wwan
<6>[ 21.350000] br0: port 4(ath1) entered forwarding state
<6>[ 21.510000] usbcore: registered new interface driver usbserial
<6>[ 21.510000] usbcore: registered new interface driver usbserial_generic
<6>[ 21.520000] USB Serial support registered for generic
<6>[ 21.530000] usbserial: USB Serial Driver core
<6>[ 21.580000] usbcore: registered new interface driver sierra
<6>[ 21.580000] USB Serial support registered for Sierra USB modem
<6>[ 21.710000] usbcore: registered new interface driver option
<6>[ 21.710000] USB Serial support registered for GSM modem (1-port)
<6>[ 22.800000] etherip: Ethernet over IPv4 tunneling driver |
|
|
