The_Joe DD-WRT Novice
Joined: 21 Mar 2014 Posts: 3
|
Posted: Fri Mar 21, 2014 2:53 Post subject: Preparing to Serial Flash my RNX-EasyN400 ESR-9753 |
|
Feeling scared and Noobish, Preparing to Serial Flash my RNX-EasyN400 with DD-WRT.
I have been reading, I think I understand the basics. The most up to date information I have says I will be fallowing the same steps for this as you would for an RNX-EasyN4/ESR-9752.
I will need a USB cable that has TTL Voltage levels, and then I fallow the steps shown in these threads: LINK1 LINK2 and flash the file ESR9752 v.24 sp2 - build 12527 – 20090720.
Do I have it mostly correct? Is there any updated information? Any links that might provide more detailed step by step instructions?
Thank you so much. If this fails, then the router is headed for the trash bin. |
|
The_Joe DD-WRT Novice
Joined: 21 Mar 2014 Posts: 3
|
Posted: Tue Apr 01, 2014 17:16 Post subject: |
|
Well, I am having trouble. I have serial access, I mash 2, I get to the step where I input the routers IP, the computers IP, and the filename, and then it keeps timing out.
I have a lan cable connected, I have my computer set to the correct IP, I just cant get it to work. Any help?
Code: | 2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.99.9) ==:192.168.99.9
Input server IP (192.168.99.8) ==:192.168.99.2
Input Linux Kernel filename (uImageESR-9753-rosewill) ==:firmware.bin
netboot_common, argc= 3
*************buf = 0x80fccf20
**********NexTxPacket = 80fe4fc0
NetTxPacket = 0x80FE4FC0
NetRxPackets[0] = 0x80FE55C0
NetRxPackets[1] = 0x80FE5BC0
NetRxPackets[2] = 0x80FE61C0
NetRxPackets[3] = 0x80FE67C0
NetRxPackets[4] = 0x80FE6DC0
NetRxPackets[5] = 0x80FE73C0
NetRxPackets[6] = 0x80FE79C0
NetRxPackets[7] = 0x80FE7FC0
NetRxPackets[8] = 0x80FE85C0
NetRxPackets[9] = 0x80FE8BC0
NetRxPackets[10] = 0x80FE91C0
NetRxPackets[11] = 0x80FE97C0
NetRxPackets[12] = 0x80FE9DC0
NetRxPackets[13] = 0x80FEA3C0
NetRxPackets[14] = 0x80FEA9C0
NetRxPackets[15] = 0x80FEAFC0
NetRxPackets[16] = 0x80FEB5C0
NetRxPackets[17] = 0x80FEBBC0
NetRxPackets[18] = 0x80FEC1C0
NetRxPackets[19] = 0x80FEC7C0
KSEG1ADDR(NetTxPacket) = 0xA0FE4FC0
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
Mac to giga Mac mode
rx_ring = A0FCD340, tx_ring0 = A0FCD200
Header Payload scatter function is Disable !!
RT2880_PDMA_GLO_CFG=00000020
*************************************************
RX_CALC_IDX0=19
RX_DRX_IDX0 = 0
*************************************************
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.99.2; our IP address is 192.168.99.9
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: *
ArpTimeoutCheck
T T T T checksum bad
checksum bad
checksum bad
checksum bad
T checksum bad
checksum bad
T checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
T Got ARP REPLY, set server/gtwy eth addr (6c:62:6d:45:97:a4)
Got it
T T T
Retry count exceeded; starting again
Trying Eth0 (10/100-M)
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.99.2; our IP address is 192.168.99.9
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (6c:62:6d:45:97:a4)
Got it
T T Got ARP REQUEST, return our IP
T T T T T T T T
Retry count exceeded; starting again
Trying Eth0 (10/100-M)
ETH_STATE_ACTIVE!!
Got ARP REQUEST, return our IP
Using Eth0 (10/100-M) device
TFTP from server 192.168.99.2; our IP address is 192.168.99.9
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (6c:62:6d:45:97:a4)
Got it
T T T T T T Got ARP REQUEST, return our IP
T T T T
Retry count exceeded; starting again
Trying Eth0 (10/100-M)
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.99.2; our IP address is 192.168.99.9
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (6c:62:6d:45:97:a4)
Got it
T Got ARP REQUEST, return our IP
T T T T T T T T T
Retry count exceeded; starting again
Trying Eth0 (10/100-M)
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.99.2; our IP address is 192.168.99.9
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (6c:62:6d:45:97:a4)
Got it
T T T T T T T T T T
Retry count exceeded; starting again
Trying Eth0 (10/100-M)
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.99.2; our IP address is 192.168.99.9
Filename 'firmware.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (6c:62:6d:45:97:a4)
Got it
T T T T T T T T T Got ARP REQUEST, return our IP |
This time I tried a different file name.
Code: | 2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.99.9) ==:192.168.99.9
Input server IP (192.168.99.8) ==:192.168.99.2
Input Linux Kernel filename (uImageESR-9753-rosewill) ==:z.bin
netboot_common, argc= 3
*************buf = 0x80fccf20
**********NexTxPacket = 80fe4fc0
NetTxPacket = 0x80FE4FC0
NetRxPackets[0] = 0x80FE55C0
NetRxPackets[1] = 0x80FE5BC0
NetRxPackets[2] = 0x80FE61C0
NetRxPackets[3] = 0x80FE67C0
NetRxPackets[4] = 0x80FE6DC0
NetRxPackets[5] = 0x80FE73C0
NetRxPackets[6] = 0x80FE79C0
NetRxPackets[7] = 0x80FE7FC0
NetRxPackets[8] = 0x80FE85C0
NetRxPackets[9] = 0x80FE8BC0
NetRxPackets[10] = 0x80FE91C0
NetRxPackets[11] = 0x80FE97C0
NetRxPackets[12] = 0x80FE9DC0
NetRxPackets[13] = 0x80FEA3C0
NetRxPackets[14] = 0x80FEA9C0
NetRxPackets[15] = 0x80FEAFC0
NetRxPackets[16] = 0x80FEB5C0
NetRxPackets[17] = 0x80FEBBC0
NetRxPackets[18] = 0x80FEC1C0
NetRxPackets[19] = 0x80FEC7C0
KSEG1ADDR(NetTxPacket) = 0xA0FE4FC0
NetLoop,call eth_halt !
NetLoop,call eth_init !
Trying Eth0 (10/100-M)
Waitting for RX_DMA_BUSY status Start... done
Mac to giga Mac mode
rx_ring = A0FCD340, tx_ring0 = A0FCD200
Header Payload scatter function is Disable !!
RT2880_PDMA_GLO_CFG=00000020
*************************************************
RX_CALC_IDX0=19
RX_DRX_IDX0 = 0
*************************************************
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.99.2; our IP address is 192.168.99.9
Filename 'z.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (ec:9a:74:fe:fe:0f)
Got it
Got ARP REQUEST, return our IP
T T T T T T T Got ARP REQUEST, return our IP
T T T
Retry count exceeded; starting again
Trying Eth0 (10/100-M)
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.99.2; our IP address is 192.168.99.9
Filename 'z.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (ec:9a:74:fe:fe:0f)
Got it
Got ARP REQUEST, return our IP
T T T T T T Got ARP REQUEST, return our IP
T T T T
Retry count exceeded; starting again
Trying Eth0 (10/100-M)
ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.99.2; our IP address is 192.168.99.9
Filename 'z.bin'.
TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (ec:9a:74:fe:fe:0f)
Got it
Got ARP REQUEST, return our IP
T T T T T Got ARP REQUEST, return our IP
T T T T T |
I have tried this using TFTP that comes with windows in a command prompt, I have tried TFTP2, TFTPd64, and solar winds. None of them seem to be able to interface with the the router.
Any help? |
|