No i have not. I have never had to in the paste. it was only the upgrade to 25015 that started the issue. I am wondering if there is something to the auto-mount and the fact there are two partitions ahead of it that get mounted and it only does the first two?
Could be, The thing is that I always used the UUID section to mount my drives, and i do have multiple partition's.
Posted: Mon Sep 15, 2014 1:52 Post subject: Re: Tested on Dlink Dir-868L
bcmalloy wrote:
Works well, been up for about 6 hrs everything seems to be working nicely,
Nice work Kong.
Hopefully crack the 4 day record I've had with the previous builds, just ran stock for over a week without a reboot to ensure it is indeed firmware related.
Attempted to upgrade from brainslayer build but found I had to install an older kong build before I could successfully upgrade, not sure what was going on with that possibly something to do with Safari.
The important part of this release also includes the new mipsel drivers, switch and wifi.
I had similar issues with 24500M. I always had to reboot to get any changes to take affect. Are you rebooting and not just saving and applying settings? _________________ R7000 Nighthawk - DD-WRT v3.0-r50308
R7000 Nighthawk - DD-WRT v3.0-r50308
~~~~~~~~~~Dismantled for learning opportunities~~~~~~~~~~
WRT54Gv2
WRT54Gv8.2
~~~~~~~~~~Other Settings~~~~~~~~~
https://nextdns.io/?from=2d3sq39x https://pi-hole.net/ https://github.com/DNSCrypt/dnscrypt-proxy
nope did a reboot, even went as far as erase nvram reload FW and set it up again, no joy. I can mount it just fine from the command line. Just no auto-mount.
I will add that I did add the swap partition where as before I didn't have a swap partition. but the swap gets mounted. the second partition is the one name jffs the third is opt the 4th is ftp. I never had to use UUID's to auto-mount previously. _________________ EA-6900
Asus 68U
I did a cut and paste of the upper case uuid of the first available UUID on the page to the mount info window for /opt and the second to /jffs. I even included the info in parentheses. Works fine here.
it is mounting them due to your name on them "jffs" and "opt" I doubt it even notices the UUID you put in. if you are getting them off the gui then they where already mounted. otherwise they dont show up at all and you have to telnet in and use "blkid" to get the UUID. You don't need them at all. It will auto mount partitions if the are named "swap" "opt" or "jffs"
it worked prior to adding in the swap. I wonder if there is something wrong with it when you mount a swap? _________________ EA-6900
Asus 68U
Posted: Mon Sep 15, 2014 5:52 Post subject: Re: Tested on Dlink Dir-868L
Fractal wrote:
bcmalloy wrote:
Works well, been up for about 6 hrs everything seems to be working nicely,
Nice work Kong.
Hopefully crack the 4 day record I've had with the previous builds, just ran stock for over a week without a reboot to ensure it is indeed firmware related.
Attempted to upgrade from brainslayer build but found I had to install an older kong build before I could successfully upgrade, not sure what was going on with that possibly something to do with Safari.
The important part of this release also includes the new mipsel drivers, switch and wifi.
I thought that because of change set 25003 where the arm drivers were also updated but the Broadcom driver version is the same in this build and the previous.
Posted: Mon Sep 15, 2014 7:43 Post subject: Re: Tested on Dlink Dir-868L
Gingernut wrote:
I thought that because of change set 25003 where the arm drivers were also updated but the Broadcom driver version is the same in this build and the previous.
Wasn't pulled into this build by the looks of it.
25003 looks like just one very small change to one file in the ARM driver, the rest is the same. Dropping a one bit check out of a conditional for Buffalo router, I'm guessing *smile*. I've noticed that the source commit comments are kind of sparse.
