[kt_haddock]

ftp://ftp.dd-wrt.com/betas/2014/11-20-2014-r25408/

This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build. (eg: 25408_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless.
If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.

[decompiled]

http://svn.dd-wrt.com/timeline

Looks like this build fixes issues with micro.

[Gameman Advanced Kid]

For the linksys* e3000 that I tested on, I still have issues with wireless channels on k2.6 but not on k3.x. I still need it fixed so that I can use dd-wrt on my parents Cisco m20 again.

http://svn.dd-wrt.com/ticket/3750

[JohnnySL]

weird, i do not have any wireless issues at all on mine.
channels stay where i put them

[torankusu]

Hi All,

Belkin F7D8301 v1, 30/30/30 reset and nvram.

Same issues still present on r25408.

1.ETH1 starts up with proper MAC address, seconds later changes to same MAC address as ETH2.

2.Wireless Channels Can't be manually selected if wireless network mode is set to MIXED, on both 2.4GHz(ETH1) and 5.0GHz(ETH2).

See ticket #3722 for logs.

[s-f-r-j]

Back to Kong's 24800M.

With this build, unable to hit more then 300mbit down, where with Kong's i am able to do about 330 (max my connection).

Slow SAMBA (still) - for now, sticking with 24800M.

[stalonge]

Why build #25408 for wzr1750dhp is not in the ftp files ?

ftp://ftp.dd-wrt.com/betas/2014/11-20-2014-r25408/buffalo_wzr-1750dhp/

[jimfree]

After uploading firmware the router had to be turned off and back on to complete the upgrade. I did not perform a reset after or before the upgrade. Upgraded from previous release r25309. Everything that was working before the upgrade is working after 5 hours of up time. Things specifically checked

Wifi -- both 2.4Ghz and 5GHz

Internet connection still as fast as my ISP provides, 15Mbs up and 3Mbs down. What can I say, still on DSL.

MiniDLNA - OK
Transmission - OK
SAMBA - OK
DDNS - OK

[stalonge]

[mystykmax]

Upgraded to 25408 from 25309 on r7000. Nothing is on fire. Seems to work fine.

[s-f-r-j]

You have your place insured? (just in case? )

[JAMESMTL]

Upgraded r7000 to 25408. Happy to see updated dnsmasq, option to disable radvd, and highlighting of user prompt via CLI.

Dnsmasq all-in-one support for ipv6 services and dhcpv6 address reservations via MAC address rather than duid (dhcp6s) is greatly appreciated. No negative issues here

[myersw]

Those that have loaded this on r7000 keep us posted if you have any reboot issues please. Also let us know if you made any nvram updates like ampdu=off or if running without any changes.
So far the only load that I can run is Kong 24345OLDD. All new drivers I have tried causes reboots. If I do the ampdu=off that causes Netflix streaming performance issues for me.
--bill

[rnio]

SAN FRANCISCO time zone still missing ...

[NiTrus]