QOS still not working
TEll your computer to have 1kbps down and 1 kbps up and run speedtest.net and you will still have full speed.
Please test yourself. My settings are correct.
Router crashes due to running out of space. Must be something that can be deleted so router can run with no crashes.
Very annoying when I'm on an VOIP call.
its working on atheros & this is the atheros section, ea6500 is broadcom..
Can you point me to the right section? I didn't think there was a difference? Am I downloading the wrong beta than? Thanks
A lot of people are having problems with restrictions and QOS and I really need it working.
Thanks
My router is in the beta section that I am using, it is listed. So why isnt QOS for broadcom installed?
Router Model: Buffalo WBMR-HP-G300H
Status: ok (Update from r25251)
Reset: no
Errors: no _________________ Buffalo WBMR-HP-G300H
DD-WRT v3.0-r29739 std (05/19/16)
Status: Working (not bricked)
Reset: No
Errors: so far so good
side note:
i had used the 23919 for 8 months no wifi issues, i had a issue a min ago with the last build, still could not connect after fw upgrade, fully disabled wifi on laptop and enabled it then i had a connection, not sure if my laptop acted up or the router did _________________ Router: Buffalo WZR-300HP w/ DD-WRT build #28444
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Sat Nov 22, 2014 6:36 Post subject:
BillMan wrote:
tatsuya46 wrote:
BillMan wrote:
Linksys Ea6500v1
QOS still not working
TEll your computer to have 1kbps down and 1 kbps up and run speedtest.net and you will still have full speed.
Please test yourself. My settings are correct.
Router crashes due to running out of space. Must be something that can be deleted so router can run with no crashes.
Very annoying when I'm on an VOIP call.
its working on atheros & this is the atheros section, ea6500 is broadcom..
Can you point me to the right section? I didn't think there was a difference? Am I downloading the wrong beta than? Thanks
A lot of people are having problems with restrictions and QOS and I really need it working.
Thanks
My router is in the beta section that I am using, it is listed. So why isnt QOS for broadcom installed?
Joined: 29 Jan 2010 Posts: 113 Location: Aveiro, Portugal
Posted: Sat Nov 22, 2014 15:14 Post subject: Tp_Link TL-WR741ND Ver2.0 -> Client Mode Not Working
I flashed this router with this new build but is not working in client mode. Router TpLink gets ip address from Main AP but doesn't have internet connection. I reverted back to 17201 which so far is the only one that works.
Any suggestions are welcome. Thanks _________________ »»» Marooned »»» by Pink Floyd
Router Model: TP-Link WR841Nv9/TP-Link WR842NDv1
Status: OK (updated both directly from OpenWRT Barrier Breaker LUCI GUI using factory-to-ddwrt.bin)
Reset: yes
Errors: no* (only minor issue is wireless with iPod touch 1st generation using WPA2/AES only; The iPod touch 1st gen wireless card is just too old
Thanks to all involved with DD-WRT! This release is very nice! So far working fine with wired/wireless clients in standard wireless router mode.
QOS still not working
TEll your computer to have 1kbps down and 1 kbps up and run speedtest.net and you will still have full speed.
Please test yourself. My settings are correct.
Router crashes due to running out of space. Must be something that can be deleted so router can run with no crashes.
Very annoying when I'm on an VOIP call.
its working on atheros & this is the atheros section, ea6500 is broadcom..
Can you point me to the right section? I didn't think there was a difference? Am I downloading the wrong beta than? Thanks
A lot of people are having problems with restrictions and QOS and I really need it working.
Thanks
My router is in the beta section that I am using, it is listed. So why isnt QOS for broadcom installed?
Errors: on Setup/Networking tab there is no button to delete bridge (GUI alignment overflow?)
It doesn't exist for default bridge. In my case, I can see Delete button for second bridge (If I press Add there).
Is there ever a reason you'd want to delete the default bridge?
Maybe the button has been removed because it didn't serve any useful purpose?
Edit: But I think not, on my WNDR3700v2 button is present.
Last edited by bdg2 on Sun Nov 23, 2014 23:50; edited 1 time in total
Status:OK
Reset:30/30/30
Errors: I need to set "swconfig dev eth1 set enable_vlan 1,
swconfig dev eth1 set apply" on the router to allow access in my internal lan clients to my server.
