Whoops! I didn't realize that this new build was here. Maybe these beta build threads should be stickied when a new one comes out?
Router: Netgear R6300v2
Firmware: r27360 -> r27506
Status: OK
Reset: no
Errors: website filtering doesn't seem to be working. I've added websites and some MAC addresses but it's not doing the trick.
Also I haven't decided if Transmission doesn't like web seeds or if it doesn't like having 38 transfers open, but one of the two kills the router after a short time. Might be a little of both
Joined: 27 Nov 2008 Posts: 17 Location: Alberta, Canada
Posted: Tue Aug 04, 2015 0:17 Post subject:
Router: Asus RT-AC68U
Firmware: 27506 (From 25948)
Kernel: Linux 3.10.83 #4384 SMP Wed Jul 8 05:59:05 CEST 2015 armv7l
Status: Working (Speedtest.net: 12ms/58.56 Mbps Down/3.35 Mbps Up; Speeds what expected)
Reset: Reset on Update then re-entered.
Errors: Only reboot window doesn't return to config when router is ready, have to manually do so. _________________ CWTS, CWNA, CWSP Certified
Asus AC-AC68U on build 27506
Router: R7000
Firmware: v3.0-r27506 (07/09/15) std
Kernel: Linux 3.10.83 #4384 SMP Wed Jul 8 05:59:05 CEST 2015 armv7l
Status: OK
Reset: yes, before and after loading 27506
Errors: this version had been working well for me for 3 wks or so, but yesterday I found I could not connect to the guest network. It would not accept my password from my ipad. So I did a Reboot, and that fixed it.
Router: Asus RT-AC87U
Firmware: DD-WRT v3.0-r27506 (07/09/15) std
Kernel: Linux 3.10.83 #4391 SMP Thu Jul 9 04:55:23 CEST 2015 armv7l
Status: Basics Working
Reset: Power cycle and web interface factory reset/reboot
Errors: 2.4GHz LED not working.
Unable to add new bridge. ip does not get saved.
Unable to re-configure VLAN. Changing vlan setting prevents access to router, have to factory reset.
port based VLAN now working, configure using telnet
Last edited by guiguy on Thu Aug 06, 2015 13:41; edited 1 time in total
Anyone using this build, especially anyone using a Netgear R7000, getting these messages in syslog:
Aug 6 00:38:42 DD-WRT kern.warn kernel: br0: received packet on vlan1 with own address as source address
I'm curious, since I'm using a different dd-wrt build than this one and am seeing the above messages occasionally (but more than I'd like). Doesn't seem to affect the router performance or functionality, but I'm curious if this build has these same things going on or not.
Thanks!
Update: Never mind, answered my own question fairly quickly. Yes this build gets the same weird warnings as quoted above.
If you check the wireless page, do both wl0 and wl1 (both wifi's) have the same MAC-adress? This can cause this error.
Yes, I've noticed that, and usually change the MAC address of br0 in the "Networking" tab, since it the same as the MAC address of vlan1 (as the message implies). That seems to eliminate the larger clumps of these warnings, but I still get them occasionally, but in smaller groups of 1-4 rather than 100 or so. Every few hours. So I think that the basic cause is elsewhere.
I'm sure that it's been reported before, but the two latest builds that I've used, 27525 and now 27506, both exhibit this behavior. So I may actually try and report this against the source.
Last edited by MrDoh on Thu Aug 06, 2015 22:14; edited 1 time in total
Router: Linksys E1200v2
Firmware: DD-WRT v3.0-r27506 (07/09/15) big (From 21061)
Kernel: Linux 2.6.24.111 #26261 Thu Jul 9 00:39:19 CEST 2015 mips
Status: Working
Reset: Yes, also a 30-30-30 before and after install
Errors: I have setup openDNS using DDNS for my dynamic IP, it's working fine but some reason GMail is no longer being block. I am not sure if this is a temporary issue from OpenDNS or the router.
Posted: Fri Aug 07, 2015 16:28 Post subject: Virtual interface not working!
Router: D-Link DIR860L Rev. A1
Status: internet - ok
Reset: Yes. Did 30-30-30.
Errors: Virtual interface not working
Cannot get IP address using DHCP. Still cannot connect using static IP.
Tried different combination with physical interface - AP mode or repeater mode, 2.4G or 5G, same SSIDs or different SSIDs, wireless security enabled or disabled, etc. Also I think it's worth mentioning that SSID can't be found if applying wireless security (WPA2+AES) on virtual interface. Can see broadcasting if wireless security disabled though, so weird.
Everything else works flawless. Had to switch back to v24-sp2 (06/05/15) std, where LED doesn't work but Virtual interface is normal under both AP/repeater mode. (LED is fixed in 07/09/15 ver.)
Posted: Sun Aug 09, 2015 5:25 Post subject: Re: Virtual interface not working!
et3606 wrote:
Also I think it's worth mentioning that SSID can't be found if applying wireless security (WPA2+AES) on virtual interface. Can see broadcasting if wireless security disabled though, so weird.
FWIW, they're broadcast here when set that way.
What doesn't seem to work here though is QoS: no matter what I set the uplink to, I get full speed. It's as if it's not set at all. Rebooted. HTB and HFSC.
tried flashing dd-wrt.v24-27506_NEWD-2_K3.x_mega-nv64k.bin to my wndr3400v1, it bricked, after using the pin shorting method to unbrick it, i flashed dd-wrt.v24-27506_NEWD-2_K2.6_big-nv64k.bin to my wndr3400v1, set it up as repeater bridge on 5ghz, it is working properly, however vap's dont seem to work, so 2.4 is a AP, after that i flashed the same k2.6 to my wndr3700v3, i didnt wanna brick that one because its in my parents house and im next door, im not sure if mega is too big or what, but when just the orange light is on for 5 minutes its never a good thing, thanks for the support! and soon i will try it on my rt-n12, but the antennas are broke on that one, and the wan port is slow, its just a old spare.
ive seen that other people had this working for their 3700v3's, my 3400v1 is basically the same as the 3700v3, so idk why it doesnt work...
Router: wndr3400v1
Firmware: DD-WRT v3.0-r27506 (07/09/15) big
Kernel:
Status: great
Reset: none
Errors: Repeater Bridge, weird thing happen with VAP
gui to access router setting in RB breaks, so 1 shot to set up and you have to reset defaults to re-setup, but its working good regardless
Router: wndr3700v3
Firmware: DD-WRT v3.0-r27506 (07/09/15) big
Kernel: Linux 2.6.24.111 #26261 Thu Jul 9 00:39:19 CEST 2015 mips
Status: awesome
Reset: none
Errors: none, regular AP configuration, 5ghz and 2.4 work well
