[PITABoy]

DD-WRT build 28139 - 2015/11/13 has been released: ftp://ftp.dd-wrt.com/betas/2015/11-13-2015-r28139/

Changelog excerpt from http://www.dd-wrt.com/phpBB2/viewtopic.php?t=279466

[117] Fix: WebGUI menu http://svn.dd-wrt.com/ticket/4897
[138-139] Fix: NVRAM backup
[119-121] Fix: Broadcom/ARM core affinity
[129-130] Upd: Broadcom/ARM driver
[113-114] Upd: ProFTPD 1.3.5a
[125-126] Upd: Wireless tools
[133-135] Add: speedtest-cli
[136-137] Add: EA6350 support


Your reports for Broadcom units are highly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:


This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 28139M_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.

[onnoossendrijver]

Seems to run fine on my D-Link DIR-880L

[a_l]

DD-WRT v3.0-r28139 std (c) 2015 NewMedia-NET GmbH
Release: 11/13/15
D-Link DIR-860L A1
Earlier build: r28112
Reset to Defaults: Yes

Just like build r28112 ( https://www.dd-wrt.com/phpBB2/viewtopic.php?p=991342#991342 and https://www.dd-wrt.com/phpBB2/viewtopic.php?p=991546#991546 ) this build also have a Power LED that blinks yellow/green and sometimes is only yellow. It should however be constant green after boot, but it isn't!

WiFi and Cable connection to Internet works.

After I load a very old configuration file from long before r28072 the Power LED becomes constant green when the router has rebooted.

Strange!

[mrjcd]

E2500 v1
DD-WRT v3.0-r28139 mega (11/13/15)
Linux 2.6.24.111 #27398 Fri Nov 13 02:36:17 CET 2015 mips
[dd-wrt.v24-28139_NEWD-2_K2.6_mega-nv60k.bin]
no reset - previous 27858_NEWD-2_K2.6_mega-nv60k.bin

Same problem as 27858 --and I assume last couple K2.6 builds --
VAP will NOT broadcast if security encryption is enabled

download speed
wired 93.80 Mbps
2.4GHz wireless HT40 wide 73.12 Mbps (that's w/laptop Dell wl 1703 card) the android lolipop
or the jellybean won't do but top of 57 with steady 43~47
That's 'bout good as I can do with tomato using the 5Ghz band
installed 25974_NEWD-2_K2.6_mega-nv60k.bin over that without reset
and VAP is back to working so the old build will have to do for now

I love my old routers -- thank you thank you goodbye

[redhawk0]

Running good on my broadcom units...but on my RT-N16 units the NVRAM usage is incorrectly displayed.

Running the K3.0 big build on this unit.

0.02K/256K

redhawk

[colnago]

Router: EA6900
Firmware: Linksys-ea6900-webflash.bin
Kernel: Linux 3.10.93 #4927 SMP Fri Nov 13 06:54:51 CET 2015 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
SSH: OK
VPN Client: OK
Status: Working
Error(s): none yet encountered
Uptime: 1 hour

Not reset from r28112

The Wireless -> WL1-WDS tab is accessible again.

[hwaddwrt]

Router: Netgear WNDR4500
Firmware: DD-WRT v3.0-r28139 giga (11/13/15)
Kernel: Linux 3.10.93 #10164 Fri Nov 13 10:20:22 CET 2015 mips
Status: works with the exception of NVRAM
Reset: yes
Errors: yes

As reported for the previous build, the backup is only 8 bytes (just the DD-WRT header) and

[KrypteX]

[Fractal]

nvram shows correctly on R7000 in both UI and on CLI

nvram show
size: 43774 bytes (21762 left)

[greedj]

nvram backup works.
All VAPs are visable.
WPA2 enterprise works.
Seems to be working better than r28072, not sluggish so far.

[Mogaku-san]

Router: D-link DIR880L
DD-WRT Version: DD-WRT v3.0-r28139 std (11/13/15)
2.4GHz (b/g/n): OK
5GHz (ac/n/a): OK

Like previous version v3.0-r28112 std (11/10/15) the LEDs for 2.4 and 5GHz is only on during boot, but is later switched off.

[Bernadoe]

Router: Netgear R7000
Firmware: DD-WRT v3.0-r28139 std (11/13/15)
Kernel: Linux 3.10.93 #4927 SMP Fri Nov 13 06:54:51 CET 2015 armv7l
Status: Working
Reset: No
Errors: No

[jrscs]

Build 28139 previous build 28112

Router: RT-AC87U - primary router/gateway
Firmware: asus_rt-ac87u-firmware.trx
Kernel: Linux 3.10.93 #4934 SMP Fri Nov 13 07:15:32 CET 2015 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
VNC Repeater: OK
USB 2.0 storage ext3 mount to JFFS: OK
USB 3.0 storage NTFS mount to MNT: OK
NAS Samba shared drive: OK
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: 2.4Ghz OK – 5Ghz NO
Reset via GUI: Yes before and after upgrade
Status: Working
Error(s): Guest network does not show any output signal, noise, or SNR in the client’s output table

Router: RT-AC68R - primary router/gateway
Firmware: asus_rt-ac68u-firmware.trx
Kernel: Linux 3.10.93 #4927 SMP Fri Nov 13 06:54:51 CET 2015 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
VNC Repeater: OK
USB 2.0 storage ext3 mount to JFFS: OK
USB 3.0 storage NTFS mount to MNT: OK
NAS Samba shared drive: OK
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: NO
Reset via GUI: Yes before and after upgrade
Status: Working
Error(s): Guest network does not show any output signal, noise, or SNR in the client’s output table

Repeater Bridge Build 28139 previous build 28112

Router: RT-AC66U - Repeater Bridge on 5 Ghz (AC-Only) to RT-AC87U
Firmware: dd-wrt-28139-Asus_RT-AC66.trx
Kernel: Linux 3.10.93 #10164 Fri Nov 13 10:20:22 CET 2015 mips
2.4Ghz (NG-mixed) with 20Mhz channel width: OK
5Ghz (AC-Only): OK
Reset via GUI: Yes before and after upgrade
Status: Working
Error(s): OK

** Builds after 26339 when erasing NVRAM in telnet session or Power UP Reset, resets 5.0 GHz radio to 2.4 GHz radios – To recover return to 26339 ***
*** Builds after 26339 use the Administration >> Factory Defaults tab in the GUI to reset NVRAM ***
*** Since 27343 the following command needs to be included in the Start-up script, ‘sleep 5; startstop lan’ to allow the 5 Ghz to connect to the main AP in Repeater Bride mode when rebooting. Thanks to Magnetron 1.1 for putting in forum topic ***

Router: e4200 – Repeater Bridge on 5 Ghz (N) to RT-AC87U
Firmware: dd-wrt.v24-28139_NEWD-2_K3.x_mega-e4200.bin
Kernal: Linux 3.10.93 #10180 Fri Nov 13 10:32:51 CET 2015 mips
2.4Ghz (NG-mixed) with 20Mhz channel width: OK
5Ghz (N):OK
Reset via GUI: Yes before and after upgrade
Status: Working
Error(s): OK

*** Since 27343 the following command needs to be included in the Start-up script, ‘sleep 5; startstop lan’ to allow the 5 Ghz to connect to the main AP in Repeater Bride mode when rebooting. Thanks to Magnetron 1.1 for putting in forum topic ***

[mrjcd]

E2500
same box as had the K2.6 erased / reset

Installed
DD-WRT v3.0-r28139 mega (11/13/15)
Linux 3.10.93 #10180 Fri Nov 13 10:32:51 CET 2015 mips

yay... a secured VAP works ok on this build but nvram shows same as others mentioned.
Same in GUI as Redhawk and same in CL

[cookieboyeli]