[GreyDoc]

DD-WRT build 28598 - 2015/12/24 has been released: ftp://ftp.dd-wrt.com/betas/2015/12-24-2015-r28598/

Changelog: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=279468

Your reports for Ralink/Mediatek units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:

This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 28598_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.

[h8red]

Router: Asus-rt-n10plus C1
Firmware: DD-WRT v3.0-r28598
Kernel: Linux 3.2.74 #21123
Status: OK
Reset: no
Errors: no

Web upgrade from r28444. All versions 28493 to 28586 bricks the router.

[hubermania]

Router: Asus rt-n10plus B1
Firmware: DD-WRT v3.0-r28598
Previous: DD-WRT v3.0-r27506
Kernel: Linux 3.2.74 #21123
Status: OK
Reset: Yes via GUI
Errors: No

Web update from r27506, reset via GUI.
Physical wireless interface OK
Virtual wireless interface OK (bridged)
SSH access OK, fingerprint has changed.

DD-WRT or Comcast must have given me a Christmas gift. As of today's update, my downlink speed increased from 20mbps to 30mbps!

[Alozaros]

well after tons of try's somehow i was able to recover to stock and then to 29444 once i decided to give a go to 28579 after nvram erase everything was ok for few hours and then router went to reboot loop, and then again non of the try's to upload any of the FW stock or dd-wrt fails around 50% and router gets to reboot loop... it seems i have to use ttl to usb, as there is a socket for that...

anyone of you experienced with the procedure to recover it will be highly appreciated for me to be able to use my Rlink device as well big thanks in advance ..

[aximpda-dd]

Router: Buffalo WCR-GN
Firmware: DD-WRT v3.0-r28598 std (12/24/15)
Kernel: Linux 3.2.74 #21133 Thu Dec 24 10:37:32 CET 2015 mips
Status: stable
Reset: no
Errors: have not found

[Louis-Jean]

Router: D-Link DIR600 rev b
Firmware: Firmware: DD-WRT v3.0-r28598 std (12/24/15)
Kernel: Linux 3.2.74 #21093 Thu Dec 24 10:14:15 CET 2015 mips
Status: LAN ports all stopped working
Reset: 30-30-30 reset before flashing, reset to defaults after
flash (via DD-WRT GUI)
Errors: none
Upgraded from build 28579

LAN port 4 was working from Saturday afternoon when I flashed this build until just now (Monday noon), when I moved my Ethernet cable to test ports 1 through 3. When I moved it back to port 4 that port no longer worked either. The lights on the router for the LAN ports don't light and my computer reports no network connection on eth0. My Ethernet cable tests good: plugging it in to a different router gives me a connection. I'm using a static IP address. Am on wifi now.

Everything else seems stable and functional. The wifi channel no longer changes to ch. 1 as it frequently did on build 28579. The wifi signal seems stronger with this build too.

Update: LAN port 4 started working again after about 30 minutes, where before it would work as soon as I plugged my cable into it. These are the same symptoms I'm having on the other LAN ports (if they work at all, it takes around 30 minutes before they begin to do so, and they're unreliable: they quit working every so often.)