Router: TP-Link TL-WR841ND
Firmware: r29519
Kernel:
Status: Wifi is semi-broken.
Reset: No
Errors: Wifi died today after installing it on the 26th (about 2 days of uptime). The wifi shows up in the network list on my devices by no devices is able to connect to it. Reboot fixed the problem (at least temporarily?). Downgraded to the previous version before 29519.
Router: DLink-DIR-615 C2
Firmware: DD-WRT v3.0-r29519 std (04/25/16)
Status: OK
Reset: NO
Errors: minor errors in the LEDs (see below).
1- WAN and Power LEDs: Not working properly.
WAN Led(the Globe in front of the router) is always orange, no matter whether internet connection is active or not. The proper state should be green for active internet connection and orange for no internet.
Power LED: During boot process, this LED stays orange (that´s fine). However, when the boot process finishes the power led is turned off. No light at all.
Other LEDS such as Wi-Fi and LAN Ports 1,2,3 and 4 are working properly.
2- Wireless Network Mode on N-Only does not work.
If I set to N-Only I am not able to connect wirelessly.
However, if I set it to NG-Mixed mode everything works fine.
Router:TP-Link TL-WR941ND v3 and v4
Firmware: web upgrade from 29316
Kernel: Linux 3.10.101 #21871 Mon Apr 25 03:24:07 CEST 2016 mips
Status: ok
Reset: no
Errors: yes
Router: DIR-862L HW:A1
Firmware: v3.0-r29519
Kernel: Linux 3.18.31 #11410
Status: Good*
Reset: Not needed but did anyway
Errors: None
I initially had an issue with my LG G4 not connecting to the 5Ghz radio (right in front of the router) but, after turning off the 2.4Ghz radio and toggling the WiFi on my phone it connected fine and stayed connected even after turning the 2.4 back on. I'm going to chalk it up to phone weirdness. Got my PATs and NATs going just fine. Now just need to work on the VPN this weekend. I'll report back if I run into any other issues.
Thanks for all your hard work!
*EDIT - For some reason my phone keeps on defaulting back to the 2.4Ghz radio. I noticed in the advanced settings section that the default TX power for 2.4Ghz is 30dBm but for the 5Ghz it's only 16dBm(?) Is this by design? Is there any danger in adjusting these both to around 26dBm?
I noticed in the advanced settings section that the default TX power for 2.4Ghz is 30dBm but for the 5Ghz it's only 16dBm(?) Is this by design? Is there any danger in adjusting these both to around 26dBm?
See the recommended wireless settings in this DD-WRT wiki article...
I noticed in the advanced settings section that the default TX power for 2.4Ghz is 30dBm but for the 5Ghz it's only 16dBm(?) Is this by design? Is there any danger in adjusting these both to around 26dBm?
See the recommended wireless settings in this DD-WRT wiki article...
Router: TPLINK ARCHER-C7 v2
Firmware: DD-WRT v3.0-r29519 std (04/25/16)
Kernel: Linux 3.18.31 #11402 Mon Apr 25 03:54:19 CEST 2016 mips
Status: Working
Reset: No
Errors: None so far
Upgraded from 03-07-2016-r29218
I noticed three warnings I have not seen before in syslogd...
kern.warn kernel: [ 6.490000] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
Status: ok
Reset: no
Errors: Not detecting several usb external drives.
Not sure if this has to do with the new release or that I had to swap external drives, however I am having an issue with detecting several usb external drives that were detecting previously. I do not recall the previous build these worked on.
Out of the following 3 USB drives only the Toshiba drive is detected unfortunately the drive is failing:
