ASUS RT-N12+: failed to flash using Restoration Utility

Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware
View previous topic :: View next topic  
Author Message
Antime
DD-WRT Novice


Joined: 04 Aug 2016
Posts: 2
PostPosted: Thu Aug 04, 2016 14:51    Post subject: ASUS RT-N12+: failed to flash using Restoration Utility Reply with quote
I have recently bought an ASUS RT-N12+ (RT N12plus). The sticker says it is HW version A. Firmware version is 3.0.0.4.378.6975. Wiki (https://www.dd-wrt.com/wiki/index.php/Asus_RT-N12) says I have to enter "rescue mode" by unplugging power connector, holding reset button and while still holding it, plug power connector back. But instead of power LED slowly blinking on and off, three LEDs (Wi-Fi, Internet and LAN) started blinking while power LED stays on.

Bellow follows what I have tried afterwards, using ASUS Firmware Restoration Utility (version 2.0.0.0) from PC with 192.168.1.10, 255.255.255.0 LAN setup:

1) Flash router with recommended dd-wrt.v24-14929_NEWD-2_K2.6_mini_RT-N12.trx - it seems to me that the Firmware Restoration Utility can find the router. It uploads the firmware and displays: "System recovery succeeds! Please wait for system reboot.". Wi-Fi, Internet and LAN LEDs stay off while power LED stays on. After nearly 30 minutes of waiting, nothing have changed, so I have unplugged power connector, waited for 10 seconds and plugged it back. The router started, but on 192.168.1.1 there still is original ASUS firmware (version 3.0.0.4.378.6975) login page.

2) Flash router with dd-wrt.v24-14896_NEWD-2_K2.6_mini_RT-N12.trx - same result as above.

3) Flash router with ASUS firmware version 3.0.0.4.380.3590 - shortly after the Firmware Restoration Utility uploaded the firmware, Wi-Fi LED started blinking and after few moments the LAN LED turned on too. So with original ASUS firmware, the flash was successful.

I think that "rescue mode" is (newly?) indicated by blinking of three LEDs (Wi-Fi, Internet and LAN) instead of blinking of power LED.

However, the ASUS Firmware Restoration Utility 2.0.0.0 probably cannot install dd-wrt.v24-14929_NEWD-2_K2.6_mini_RT-N12.trx or dd-wrt.v24-14896_NEWD-2_K2.6_mini_RT-N12.trx.

Could anybody help me, please?
Back to top View user's profile Send private message
Sponsor
Antime
DD-WRT Novice


Joined: 04 Aug 2016
Posts: 2
PostPosted: Fri Aug 05, 2016 19:14    Post subject: Reply with quote
Bump.
Back to top View user's profile Send private message
js1662
DD-WRT Guru


Joined: 23 Jul 2014
Posts: 1237
Location: BC, CA
PostPosted: Fri Aug 05, 2016 22:42    Post subject: Reply with quote
It is because RT-N12+ is not supported by dd-wrt. It is not listed on the Supported Devices List: http://www.dd-wrt.com/wiki/index.php/Supported_Devices

RT-N12 and RT-N12+ use different chip and you are lucky that you didn't brick your router by flashing a RT-N12 firmware on RT-N12+
Back to top View user's profile Send private message
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 6290
Location: Texas
PostPosted: Sat Aug 06, 2016 15:51    Post subject: Reply with quote
EDIT:
May just disregard all below --- I see this is not broadcom.
http://www.dd-wrt.com/phpBB2/viewtopic.php?p=994104
Too bad the d1 is broadcom ... sorry
-------------

If you want to pursue this ---
Since the RT-N12+ is not supported you can look thru these links
about the RT-N12-D1 (also not supported)

http://www.dd-wrt.com/phpBB2/viewtopic.php?p=992066#992066

http://www.dd-wrt.com/phpBB2/viewtopic.php?p=993566

http://www.craigonsite.com/blog/2014/12/21/how-to-install-dd-wrt-on-the-asus-rt-n12-d1

Be aware of the port changes WAN/LAN but with the d1 it fixes itself upon install dd-wrt 2 times and only reverts if have to use WPS button to reset.
You can of course also correct the ports using the CL.

The d1 is supported by Shibby Tomato and works well but I don't see FW for the + so I would be careful with that.

I don't even know what flash the router has but I would start with the
dd-wrt.v24-26125_NEWD-2_K2.6_mini.bin if I were you.

good luck -
Back to top View user's profile Send private message
psnl
DD-WRT Novice


Joined: 25 Dec 2016
Posts: 2
PostPosted: Sun Dec 25, 2016 17:47    Post subject: rt-n12+ is far different from n12 Reply with quote
When i look at log, i can see it s using

MT7620N chip.

My question is, can i flash other firmware that use same chip?



Code:
Aug  1 02:00:12 syslogd started: BusyBox v1.17.4
Aug  1 02:00:12 kernel: klogd started: BusyBox v1.17.4 (2016-06-12 06:45:54 CST)
Aug  1 02:00:12 kernel: Linux version 2.6.36 (root@asus) (gcc version 4.2.4) #1 Sun Jun 12 06:49:01 CST 2016
Aug  1 02:00:12 kernel:  The CPU feqenuce set to 580 MHz
Aug  1 02:00:12 kernel:  PCIE: bypass PCIe DLL.
Aug  1 02:00:12 kernel:  PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
Aug  1 02:00:12 kernel:  disable all power about PCIe
Aug  1 02:00:12 kernel:  PCIE: PLL power down for MT7620N
Aug  1 02:00:12 kernel: Zone PFN ranges:
Aug  1 02:00:12 kernel:   Normal   0x00000000 -> 0x00002000
Aug  1 02:00:12 kernel: Movable zone start PFN for each node
Aug  1 02:00:12 kernel: early_node_map[1] active PFN ranges
Aug  1 02:00:12 kernel:     0: 0x00000000 -> 0x00002000
Aug  1 02:00:12 kernel: Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 8128
Aug  1 02:00:12 kernel: Kernel command line: console=ttyS1,115200n8 root=/dev/mtdblock4 rootfstype=squashfs
Aug  1 02:00:12 kernel: Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Aug  1 02:00:12 kernel: Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Aug  1 02:00:12 kernel: init_r4k_clocksource: cpu_has_counter(128) mips_hpt_frequency(290000000)
Aug  1 02:00:12 kernel: new mips_hpt_frequency(289260310)
Aug  1 02:00:12 kernel: Mount-cache hash table entries: 512
Aug  1 02:00:12 kernel: bio: create slab <bio-0> at 0
Aug  1 02:00:12 kernel: Ralink gpio driver initialized
Aug  1 02:00:12 kernel: Ralink SPI flash driver, SPI clock: 24MHz
Aug  1 02:00:12 kernel: deice id : c2 20 17 c2 20 (2017c220)
Aug  1 02:00:12 kernel: MX25L6405D(c2 2017c220) (8192 Kbytes)
Aug  1 02:00:12 kernel: mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Aug  1 02:00:12 kernel: partion 3: ffffffff 7b0000
Aug  1 02:00:12 kernel: partion 4: 12e200 6d1e00
Aug  1 02:00:12 kernel: #add mtd partition#
Aug  1 02:00:12 kernel: Creating 6 MTD partitions on "raspi":
Aug  1 02:00:12 kernel: 0x000000000000-0x000000030000 : "Bootloader"
Aug  1 02:00:12 kernel: 0x000000030000-0x000000040000 : "nvram"
Aug  1 02:00:12 kernel: 0x000000040000-0x000000050000 : "Factory"
Aug  1 02:00:12 kernel: 0x000000050000-0x000000800000 : "linux"
Aug  1 02:00:12 kernel: 0x00000012e200-0x000000800000 : "rootfs"
Aug  1 02:00:12 kernel: 0x000000000000-0x000000800000 : "ALL"
Aug  1 02:00:12 kernel: rdm_major = 253
Aug  1 02:00:12 kernel: Allocate 4096 entries coherent memory for hw_nat. (262144 bytes)
Aug  1 02:00:12 kernel: SMACCR1 -- : 0x0000000c
Aug  1 02:00:12 kernel: SMACCR0 -- : 0x43762077
Aug  1 02:00:12 kernel: Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!
Aug  1 02:00:12 kernel: SMACCR1 -- : 0x0000000c
Aug  1 02:00:12 kernel: SMACCR0 -- : 0x43762077
Aug  1 02:00:12 kernel: PROC INIT OK!
Aug  1 02:00:12 kernel: matchsize=262
Aug  1 02:00:12 kernel: gre: can't add protocol
Aug  1 02:00:12 kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Aug  1 02:00:12 kernel: offset 0x1000 elapse 0ms
Aug  1 02:00:12 kernel: bled: GPIO#44: switch ports mask        0.
Aug  1 02:00:12 kernel: Algorithmics/MIPS FPU Emulator v1.5
Aug  1 02:00:12 kernel: rt2860v2_ap: module license 'Proprietary' taints kernel.
Aug  1 02:00:12 kernel: Disabling lock debugging due to kernel taint
Aug  1 02:00:12 kernel: rt2860v2:
Aug  1 02:00:12 kernel: === pAd = c04dc000, size = 1073736 ===
Aug  1 02:00:12 kernel: <-- RTMPAllocTxRxRingMemory, Status=0
Aug  1 02:00:12 kernel: <-- RTMPAllocAdapterBlock, Status=0
Aug  1 02:00:12 kernel: rt2860v2:AP Driver version-2.7.2.0_edcca_monitor_20131222
Aug  1 02:00:12 kernel: Raeth v3.1 (Tasklet,SkbRecycle)
Aug  1 02:00:12 kernel: phy_tx_ring = 0x0176e000, tx_ring = 0xa176e000
Aug  1 02:00:12 kernel: phy_rx_ring0 = 0x017f0000, rx_ring0 = 0xa17f0000
Aug  1 02:00:12 kernel: SMACCR1 -- : 0x000014dd
Aug  1 02:00:12 kernel: SMACCR0 -- : 0xa9ccbff4
Aug  1 02:00:12 kernel: ESW: Link Status Changed - WAN (P4) Link DOWN
Aug  1 02:00:12 kernel: ESW: Link Status Changed - LAN2 (P2) Link DOWN
Aug  1 02:00:12 kernel: CDMA_CSG_CFG = 81000000
Aug  1 02:00:12 kernel: GDMA1_FWD_CFG = 20710000
Aug  1 02:00:13 kernel: rt2860v2:RX DESC a13f0000  size = 2048
Aug  1 02:00:13 kernel: rt2860v2:APSDCapable[0]=1
Aug  1 02:00:13 kernel: rt2860v2:APSDCapable[1]=1
Aug  1 02:00:13 kernel: rt2860v2:APSDCapable[2]=1
Aug  1 02:00:13 kernel: rt2860v2:APSDCapable[3]=1
Aug  1 02:00:13 kernel: rt2860v2:APSDCapable[4]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[5]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[6]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[7]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[8]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[9]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[10]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[11]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[12]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[13]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[14]=1
Aug  1 02:00:14 kernel: rt2860v2:APSDCapable[15]=1
Aug  1 02:00:14 kernel: rt2860v2:default ApCliAPSDCapable[0]=1
Aug  1 02:00:14 kernel: rt2860v2:pAd->ed_chk = 1
Aug  1 02:00:14 kernel: rt2860v2:Key1Str is Invalid key length(0) or Type(0)
Aug  1 02:00:14 kernel: rt2860v2:Key2Str is Invalid key length(0) or Type(0)
Aug  1 02:00:14 kernel: rt2860v2:Key3Str is Invalid key length(0) or Type(0)
Aug  1 02:00:14 kernel: rt2860v2:Key4Str is Invalid key length(0) or Type(0)
Aug  1 02:00:14 kernel: rt2860v2:RTMPSetDefaultChannel() : default channel to 1
Aug  1 02:00:14 kernel: rt2860v2:1. Phy Mode = 9
Aug  1 02:00:14 kernel: rt2860v2:2. Phy Mode = 9
Aug  1 02:00:14 kernel: rt2860v2:E2PROM: D0 target power=0xff23
Aug  1 02:00:14 kernel: rt2860v2:E2PROM: 40 MW Power Delta= 1
Aug  1 02:00:14 kernel: rt2860v2:3. Phy Mode = 9
Aug  1 02:00:14 kernel: rt2860v2:^[[mAntCfgInit: primary/secondary ant 0/1
Aug  1 02:00:14 kernel: ^[[mrt2860v2:Initialize RF Central Registers for E2 !!!
Aug  1 02:00:14 kernel: rt2860v2:Initialize RF Central Registers for E3 !!!
Aug  1 02:00:14 kernel: rt2860v2:Initialize RF Channel Registers for E2 !!!
Aug  1 02:00:14 kernel: rt2860v2:Initialize RF Channel Registers for E3 !!!
Aug  1 02:00:14 kernel: rt2860v2:Initialize RF DCCal Registers for E2 !!!
Aug  1 02:00:14 kernel: rt2860v2:Initialize RF DCCal Registers for E3 !!!
Aug  1 02:00:14 kernel: rt2860v2:D1 = -3, D2 = 7, CalCode = 23 !!!
Aug  1 02:00:14 kernel: rt2860v2:RT6352_Temperature_Init : BBPR49 = 0xfffffffd
Aug  1 02:00:14 kernel: rt2860v2:RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff3
Aug  1 02:00:14 kernel: rt2860v2:Current Temperature from BBP_R49=0xfffffff0
Aug  1 02:00:14 kernel: rt2860v2:RT6352_TssiTableAdjust: upper_bound = 0x7F decimal: 127
Aug  1 02:00:14 kernel: rt2860v2:RT6352_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
Aug  1 02:00:14 kernel: rt2860v2:*** RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -128 -128 -128 -23 -18 -4
Aug  1 02:00:14 kernel:  - 10 - 26 39 127 127 127 127 127, offset=-13, tuning=0
Aug  1 02:00:14 kernel: rt2860v2:RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -128 -128 -128 -36 -31 -17 - -3 - 13 26 114 114 114 114 114, offset=-13, tuning=0
Aug  1 02:00:14 kernel: rt2860v2:mp_temperature=0x00, step = +0
Aug  1 02:00:14 kernel: rt2860v2:E2PROM: G Tssi[-7 .. +7] = -128 -128 -128 -128 -36 -31 -17 - -3 - 13 26 114 114 114 114 114, offset=-13, tuning=0
Aug  1 02:00:14 kernel: rt2860v2: TX BW Filter Calibration !!!
Aug  1 02:00:14 kernel: rt2860v2: RX BW Filter Calibration !!!
Aug  1 02:00:14 kernel: rt2860v2:LOFT Calibration Done!
Aug  1 02:00:14 kernel: rt2860v2:IQCalibration Start!
Aug  1 02:00:14 kernel: rt2860v2:IQCalibration Done! CH = 0, (gain= 1, phase=3d)
Aug  1 02:00:14 kernel: rt2860v2:IQCalibration Start!
Aug  1 02:00:14 kernel: rt2860v2:IQCalibration Done! CH = 1, (gain= 0, phase=3e)
Aug  1 02:00:14 kernel: rt2860v2:TX IQ Calibration Done!
Aug  1 02:00:14 kernel: rt2860v2:bAutoTxAgcG = 0
Aug  1 02:00:14 kernel: rt2860v2:MCS Set = ff ff 00 00 01
Aug  1 02:00:14 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug  1 02:00:17 kernel:  ch10 bssid=cc:a2:23:e6:5d:5d
Aug  1 02:00:17 kernel:  ch10 bssid=c4:f0:81:12:20:a8
Aug  1 02:00:17 kernel:  ch11 bssid=fc:4a:e9:43:fd:17
Aug  1 02:00:17 kernel: =====================================================
Aug  1 02:00:17 kernel: Channel 1 : Dirty = 0, False CCA = 21, Busy Time = 530, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 2 : Dirty = 0, False CCA = 7, Busy Time = 1504, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 3 : Dirty = 0, False CCA = 101, Busy Time = 2683, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 4 : Dirty = 0, False CCA = 78, Busy Time = 1389, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 5 : Dirty = 0, False CCA = 21, Busy Time = 1005, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 6 : Dirty = 40, False CCA = 33, Busy Time = 2904, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 7 : Dirty = 68, False CCA = 17, Busy Time = 39940, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 8 : Dirty = 80, False CCA = 7, Busy Time = 1918, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 9 : Dirty = 92, False CCA = 0, Busy Time = 5, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 10 : Dirty = 172, False CCA = 4, Busy Time = 5179, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 11 : Dirty = 134, False CCA = 57, Busy Time = 3075, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 12 : Dirty = 88, False CCA = 5, Busy Time = 92, Skip Channel = FALSE
Aug  1 02:00:17 kernel: Channel 13 : Dirty = 76, False CCA = 2, Busy Time = 56, Skip Channel = FALSE
Aug  1 02:00:17 kernel: =====================================================
Aug  1 02:00:17 kernel: Rule 1 CCA value : Min Dirtiness (Include extension channel) ==> Select Channel 1
Aug  1 02:00:17 kernel: Min Dirty = 0
Aug  1 02:00:17 kernel: ExChannel = 5 , 0
Aug  1 02:00:17 kernel: BW        = 40
Aug  1 02:00:17 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug  1 02:00:17 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug  1 02:00:17 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug  1 02:00:18 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug  1 02:00:18 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug  1 02:00:18 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug  1 02:00:19 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug  1 02:00:19 kernel: rt2860v2:SYNC - BBP R4 to 20MHz.l
Aug  1 02:00:19 kernel: rt2860v2:@@@ ed_monitor_init : ===>
Aug  1 02:00:19 kernel: rt2860v2:@@@ ed_monitor_init : <===
Aug  1 02:00:19 kernel: rt2860v2:Main bssid = 14:dd:a9:cc:bf:f4
Aug  1 02:00:19 kernel: <==== rt28xx_init, Status=0
Aug  1 02:00:19 kernel: 0x1300 = 00064300
Aug  1 02:00:19 kernel: rt2860v2:@@@ ed_monitor_init : ===>
Aug  1 02:00:19 kernel: rt2860v2:@@@ ed_monitor_init : <===
Aug  1 02:00:20 RT-N12+: start httpd
Aug  1 02:00:20 kernel: set watchdog pid as: 158
Aug  1 02:00:21 syslog: Generating SSL certificate...
Aug  1 02:00:22 kernel: ESW: Link Status Changed - WAN (P4) Link UP
Aug  1 02:00:22 kernel: ESW: Link Status Changed - LAN2 (P2) Link UP
Aug  1 02:00:23 kernel: rt2860v2:ASSOC - Assign AID=1 to STA f0:27:65:23:50:ec
Aug  1 02:00:26 rc_service: udhcpc_lan 177:notify_rc stop_httpd
Aug  1 02:00:26 rc_service: udhcpc_lan 177:notify_rc start_httpd
Aug  1 02:00:26 rc_service: waitting "stop_httpd" via udhcpc_lan ...
Aug  1 02:00:27 rc_service: udhcpc_lan 177:notify_rc start_dnsmasq
Aug  1 02:00:27 rc_service: waitting "start_httpd" via udhcpc_lan ...
Aug  1 02:00:27 RT-N12+: start httpd
Aug  1 02:00:28 ntp: start NTP update
Dec 24 18:19:37 kernel: rt2860v2:ASSOC - Assign AID=2 to STA a0:f3:c1:22:55:19
Dec 24 18:20:17 kernel: rt2860v2:ReASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 18:20:35 kernel: rt2860v2:ASSOC - Assign AID=1 to STA f0:27:65:23:50:ec
Dec 24 18:20:40 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 40:40:a7:4a:c1:71
Dec 24 18:22:45 kernel: rt2860v2:ASSOC - Assign AID=4 to STA 2c:0e:3d:e1:a6:d6
Dec 24 18:22:50 kernel: rt2860v2:ASSOC - Assign AID=5 to STA c4:62:ea:5c:30:25
Dec 24 18:23:02 kernel: rt2860v2:ASSOC - Assign AID=6 to STA 70:de:e2:6a:2f:e9
Dec 24 18:33:58 kernel: rt2860v2:ASSOC - Assign AID=1 to STA f0:27:65:23:50:ec
Dec 24 19:12:02 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 19:47:51 kernel: rt2860v2:ASSOC - Assign AID=4 to STA 2c:0e:3d:e1:a6:d6
Dec 24 19:52:01 kernel: rt2860v2:ASSOC - Assign AID=7 to STA 48:d2:24:8d:7d:63
Dec 24 20:15:07 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:15:24 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:15:38 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:15:53 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:16:06 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:16:20 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:18:37 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:19:10 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:19:39 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:20:04 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:20:22 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:20:54 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:21:49 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:23:10 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:23:24 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:23:44 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:24:34 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:24:46 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 0c:d2:92:03:66:f5
Dec 24 20:26:28 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 40:40:a7:4a:c1:71
Dec 24 20:27:15 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 40:40:a7:4a:c1:71
Dec 24 20:27:45 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 40:40:a7:4a:c1:71
Dec 24 20:28:31 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 40:40:a7:4a:c1:71
Dec 24 21:29:15 kernel: rt2860v2:ASSOC - Assign AID=1 to STA 8c:1a:bf:04:df:44
Dec 24 22:24:04 kernel: rt2860v2:ASSOC - Assign AID=8 to STA 78:4b:87:7d:97:96
Dec 24 22:32:58 kernel: rt2860v2:ASSOC - Assign AID=1 to STA 78:4b:87:c7:81:5e
Dec 24 23:35:43 kernel: rt2860v2:ASSOC - Assign AID=1 to STA 2c:0e:3d:e1:a6:d6
Dec 25 00:23:28 kernel: ESW: Link Status Changed - LAN2 (P2) Link DOWN
Dec 25 06:19:28 rc_service: udhcpc_lan 482:notify_rc start_dnsmasq
Dec 25 07:35:42 kernel: rt2860v2:ReASSOC - Assign AID=1 to STA 48:d2:24:8d:7d:63
Dec 25 08:41:55 kernel: rt2860v2:ASSOC - Assign AID=1 to STA f0:27:65:23:50:ec
Dec 25 08:44:12 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 78:4b:87:c7:81:5e
Dec 25 08:55:30 kernel: rt2860v2:ASSOC - Assign AID=1 to STA c4:62:ea:5c:30:25
Dec 25 09:07:04 kernel: rt2860v2:ASSOC - Assign AID=4 to STA 2c:0e:3d:e1:a6:d6
Dec 25 09:21:34 kernel: rt2860v2:ASSOC - Assign AID=5 to STA f0:27:65:23:50:ec
Dec 25 09:36:08 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 40:40:a7:4a:c1:71
Dec 25 10:27:20 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 40:40:a7:4a:c1:71
Dec 25 11:11:18 kernel: rt2860v2:ASSOC - Assign AID=2 to STA a0:f3:c1:22:55:19
Dec 25 11:18:12 kernel: rt2860v2:ASSOC - Assign AID=2 to STA a0:f3:c1:22:55:19
Dec 25 11:21:13 kernel: rt2860v2:ASSOC - Assign AID=2 to STA a0:f3:c1:22:55:19
Dec 25 12:05:18 kernel: rt2860v2:ASSOC - Assign AID=2 to STA a0:f3:c1:22:55:19
Dec 25 12:15:34 kernel: rt2860v2:ASSOC - Assign AID=2 to STA f0:27:65:23:50:ec
Dec 25 13:11:30 kernel: rt2860v2:ASSOC - Assign AID=4 to STA a0:f3:c1:22:55:19
Dec 25 13:11:32 kernel: rt2860v2:ASSOC - Assign AID=4 to STA a0:f3:c1:22:55:19
Dec 25 13:17:16 kernel: rt2860v2:ASSOC - Assign AID=2 to STA a0:f3:c1:22:55:19
Dec 25 13:26:01 kernel: rt2860v2:ASSOC - Assign AID=2 to STA a0:f3:c1:22:55:19
Dec 25 13:28:25 kernel: rt2860v2:ASSOC - Assign AID=2 to STA a0:f3:c1:22:55:19
Dec 25 13:29:18 kernel: rt2860v2:ASSOC - Assign AID=2 to STA a0:f3:c1:22:55:19
Dec 25 13:36:11 kernel: rt2860v2:ASSOC - Assign AID=2 to STA a0:f3:c1:22:55:19
Dec 25 14:05:16 kernel: rt2860v2:ASSOC - Assign AID=3 to STA f0:27:65:23:50:ec
Dec 25 14:05:19 kernel: rt2860v2:WPARetryExec::MSG1 timeout, pEntry->ReTryCounter = 11, STA f0:27:65:23:50:ec
Dec 25 14:40:09 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 38:2d:d1:fa:ae:8b
Dec 25 14:42:30 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 38:2d:d1:fa:ae:8b
Dec 25 14:43:08 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 38:2d:d1:fa:ae:8b
Dec 25 14:44:11 kernel: ESW: Link Status Changed - LAN2 (P2) Link UP
Dec 25 14:44:12 kernel: ESW: Link Status Changed - LAN2 (P2) Link DOWN
Dec 25 14:44:13 kernel: ESW: Link Status Changed - LAN2 (P2) Link UP
Dec 25 14:46:18 kernel: rt2860v2:ReASSOC - Assign AID=4 to STA 48:d2:24:8d:7d:63
Dec 25 15:27:46 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 38:2d:d1:fa:ae:8b
Dec 25 15:33:21 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 38:2d:d1:fa:ae:8b
Dec 25 15:36:47 kernel: rt2860v2:ASSOC - Assign AID=3 to STA 38:2d:d1:fa:ae:8b
Dec 25 15:43:25 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 38:2d:d1:fa:ae:8b
Dec 25 15:46:35 kernel: rt2860v2:ASSOC - Assign AID=2 to STA 38:2d:d1:fa:ae:8b
Dec 25 15:52:12 kernel: ESW: Link Status Changed - LAN2 (P2) Link DOWN
Dec 25 15:53:33 kernel: rt2860v2:ASSOC - Assign AID=2 to STA f0:27:65:23:50:ec
Dec 25 15:53:40 kernel: rt2860v2:WPARetryExec::MSG1 timeout, pEntry->ReTryCounter = 4, STA f0:27:65:23:50:ec
Dec 25 16:06:48 kernel: ESW: Link Status Changed - LAN2 (P2) Link UP
Dec 25 16:06:48 kernel: ESW: Link Status Changed - LAN2 (P2) Link DOWN
Dec 25 16:06:50 kernel: ESW: Link Status Changed - LAN2 (P2) Link UP
Dec 25 16:13:21 kernel: ESW: Link Status Changed - LAN2 (P2) Link DOWN
Dec 25 16:29:35 rc_service: httpd 181:notify_rc start_webs_update
Back to top View user's profile Send private message
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum