Posted: Thu Sep 29, 2016 20:24 Post subject: very good!
TP-Link TL-WR1043nd-v2
Web Update: OK
Reset: No
Wireless works perfect, signal is very good. In previous builds wireless didn't worked so well. I use this router as wireless to wireless repeater and now signal is much better than any other builds.
Thanks, developers!
Router: TL-WR841ND v 10
Firmware: DD-WRT v3.0-r30709 std (09/29/16)
Kernel: Linux 3.18.42 #1304 Thu Sep 29 05:05:16 CEST 2016
Status: Working as gateway
Reset: No
Errors: None
Router: DIR-615 i1
Status: OK
Reset: Defaults + erase nvram
Errors: Web UI becomes unresponsive after switching to Client Bridge Mode; unable to telnet in and must be physically unplugged/replugged to regain access.
Router Name: R7500v2
Router Model: Netgear R7500v2
Firmware Version: DD-WRT v3.0-r30709 std (09/29/16)
Kernel Version: Linux 3.18.42 #105 SMP PREEMPT Sun Sep 18 16:24:22 CEST 2016 armv7l
Status: Client bridge
Reset: No
Errors: Samba and Network Discovery
SAMBA
>ticks enable
>selects drive to be shared
>names the share
>checks "public"
>clicks "apply settings"
>waits
NETWORK DISCOVERY
>opens windows explorer
>refresh and wait a few seconds
>look at this picture ftp://gakinaction.ddns.net/IMAG1498%20-%20broadcom%20AP.jpg
>R7500v2 does show up eventually but none of the shares are in there. like an empty breifcase
WIRELESS PERFORMANCE
Latency and speed are satisfactory in my world.
DRIVE MOUNTING
If i hook up a flash drive formatted as fat32, it will at first show its not mounting and say "unsupported file system" but if i reboot the r7500v2 it will show that its mounted. Same happens if i try with other drives. did not test different file systems.
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Fri Sep 30, 2016 6:30 Post subject:
Gameman Advanced Kid wrote:
Router Name: R7500v2
Router Model: Netgear R7500v2
Firmware Version: DD-WRT v3.0-r30709 std (09/29/16)
Kernel Version: Linux 3.18.42 #105 SMP PREEMPT Sun Sep 18 16:24:22 CEST 2016 armv7l
Status: Client bridge
Reset: No
Errors: Samba and Network Discovery
SAMBA
>ticks enable
>selects drive to be shared
>names the share
>checks "public"
>clicks "apply settings"
>waits
NETWORK DISCOVERY
>opens windows explorer
>refresh and wait a few seconds
>look at this picture ftp://gakinaction.ddns.net/IMAG1498.jpg
>R7500v2 does show up eventually but none of the shares are in there. like an empty breifcase
WIRELESS PERFORMANCE
Latency and speed are satisfactory in my world.
DRIVE MOUNTING
If i hook up a flash drive formatted as fat32, it will at first show its not mounting and say "unsupported file system" but if i reboot the r7500v2 it will show that its mounted. Same happens if i try with other drives. did not test different file systems.
will send any new test results to kong.
client bridge is probably why, poor emulated bridge which is wds. client bridge breaks things like upnp, discovery etc. same here when i use it but i have 2 qca units so wds is possible. even though its connected to a marvell host have u tried wds ap <-> wds station anyway? also tried client? ie with dual nat r7500v2 on a different subnet, then try set up static routing? _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
it does not happen at all if i used a broadcom client bridge. everything works fine if i use a broadcom bridge. but if its an atheros/marvell bridge, the picture shows the problem.
i know it used to happen to broadcom units when running them in client bridged mode, but one day it just went away.
keep in mind i already have a broadcom client bridge in place and that i am just testing this unit out. i really like it so far. _________________ For people who are new to the dd-wrt forums >> http://www.catb.org/~esr/faqs/smart-questions.html#rtfm
barryware wrote:
It takes a "community" to raise a router..
Internet Connection 1
Some Techicolor modem > Linksys WRT3200ACM
Internet connection 2
Ubiquiti Powerbeam Gen 2 > Netgear R9000
Official (but not really) dd-wrt General Discussion element/matrix chat
it does not happen at all if i used a broadcom client bridge. everything works fine if i use a broadcom bridge. but if its an atheros/marvell bridge, the picture shows the problem.
i know it used to happen to broadcom units when running them in client bridged mode, but one day it just went away.
keep in mind i already have a broadcom client bridge in place and that i am just testing this unit out. i really like it so far.
Did these problems happen to you in the latest Kong's build 30700M vs. this new BS build?
it does not happen at all if i used a broadcom client bridge. everything works fine if i use a broadcom bridge. but if its an atheros/marvell bridge, the picture shows the problem.
i know it used to happen to broadcom units when running them in client bridged mode, but one day it just went away.
keep in mind i already have a broadcom client bridge in place and that i am just testing this unit out. i really like it so far.
Did these problems happen to you in the latest Kong's build 30700M vs. this new BS build?
For atheros client bridged units, yes. i did not test for all problems on marvell units and will be doing so today. _________________ For people who are new to the dd-wrt forums >> http://www.catb.org/~esr/faqs/smart-questions.html#rtfm
barryware wrote:
It takes a "community" to raise a router..
Internet Connection 1
Some Techicolor modem > Linksys WRT3200ACM
Internet connection 2
Ubiquiti Powerbeam Gen 2 > Netgear R9000
Official (but not really) dd-wrt General Discussion element/matrix chat
