Asus RT-N12 D1in dd-wrt Router Model shows RT-N12B
DD-WRT v3.0-r31825 mega (04/06/17)
Linux 3.10.105 #14402 Thu Apr 6 09:43:37 CEST 2017 mips
[dd-wrt.v24-31825_NEWD-2_K3.x_mega.bin]
install over r31791 repeater bridge
all good
Reconf as a WAP + restricted guest to leave in permanet service.
All 5 ports used in LAN
currently 4 devices on wl0, 1 on wl0.1
All good so far up 13:33
Router: Netgear r6250
Firmware: netgear-r6250-webflash.bin r31825
Previous: netgear-r6250-webflash.bin r30471
Kernel:
Status: soft-brick
Reset: yes
Errors: I was having issues upgrading to some of the later builds. I went back to an early 2015 build, then tried to flat the latest. Doing that resulted in a soft-brick.
Linksys WAP54G v3.x
DD-WRT v3.0-r31825 micro (04/06/17)
Linux 2.4.37 #45225 Thu Apr 6 04:22:31 CEST 2017 mips
WAP + Guest
Guest unbridged in wireless still no good.
But good news is br1 setup works fine and net isolation works great -- as it should
Only custom thing needed in firewall is -
iptables -I FORWARD -i br1 -d `nvram get lan_ipaddr`/`nvram get lan_netmask` -m state --state NEW -j DROP
iptables -t nat -I POSTROUTING -o br0 -j SNAT --to `nvram get lan_ipaddr`
And of course the custom DHCP for br1 in DNSMasq options
AFAIK this has been working same since 31571 .. maybe even longer ago since net isol was fixed for br1
... anyways, that is cool
Posted: Sun Apr 09, 2017 18:25 Post subject: Asus RT-AC68 and Linksys E2000
Asus RT-AC68U
DD-WRT v3.0-r31825 std (04/06/17) (previous r315791)
Kernel: Linux 4.4.59 #1388 SMP Wed Apr 5 06:30:45 CEST 2017 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
5Ghz (Mixed) with 80Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
USB 2.0 storage ext3 mount to JFFS: Ok
USB 3.0 storage EXT3 mount to /mnt: Ok
Samba shared drive: Ok
Site Survey: Ok
Wi-viz Survey 2.4Ghz & 5Ghz: Ok
Reset: No
Status: Ok
Uptime: 1 day, 7:11
CPU Temperature: CPU 74.7 °C / WL0 47.5 °C / WL1 47.0 °C
2 x E2000
DD-WRT v3.0-r31825 mega (04/06/17) (previous r31791)
Kernel: Linux 3.10.105 #14398 Thu Apr 6 09:41:12 CEST 2017 mips
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
Site Survey: Ok
Wi-viz Survey 2.4Ghz: Ok
Reset: No
Status: Ok
Uptime: 1 day, 7:21
CPU Temperature: WL0 57.5 °C
All devices working as AP's each with individual 1Gb wired connections to main firewall
Asus RT-N12 D1in dd-wrt Router Model shows RT-N12B
DD-WRT v3.0-r31825 mega (04/06/17)
Linux 3.10.105 #14402 Thu Apr 6 09:43:37 CEST 2017 mips
[dd-wrt.v24-31825_NEWD-2_K3.x_mega.bin]
install over r31791 repeater bridge
all good
Where are you downloading that build though? The ftp server doesn't show any n12 models at all.
Hi, can someone tell, please, if mobile broadband is working again?
Tried so many times, but always had to go back to 28600, the last which worked.
Would be kind, if I could get a response from so who tried it.
Thanks
Hi, can someone tell, please, if mobile broadband is working again?
Tried so many times, but always had to go back to 28600, the last which worked.
Would be kind, if I could get a response from so who tried it.
Thanks
Using R7000
Have you opened a ticket? _________________ R6400v2 (boardID:30) - Kong 36480 running since 03/09/18 - (AP - DNSMasq - AdBlocking - QoS) R7800 - BS 31924 running since 05/26/17 - (AP - OpenVPN Client - DNSMasq - AdBlocking - QoS) R7000 - BS 30771 running since 12/16/16 - (AP - NAS - FTP - SMB - OpenVPN Server - Transmission - DDNS - DNSMasq - AdBlocking - QoS) R6250 - BS 29193 running since 03/20/16 - (AP - NAS - FTP - SMB - DNSMasq - AdBlocking)
Asus RT-N12 D1in dd-wrt Router Model shows RT-N12B
DD-WRT v3.0-r31825 mega (04/06/17)
Linux 3.10.105 #14402 Thu Apr 6 09:43:37 CEST 2017 mips
[dd-wrt.v24-31825_NEWD-2_K3.x_mega.bin]
install over r31791 repeater bridge
all good
Where are you downloading that build though? The ftp server doesn't show any n12 models at all.
I included the file name in my post so there would be no confusion about this router.
You are not going to find a specific .bin for this unit because it is not fully supported probably
because the devs never had the actual unit to play with.
other info about that router
http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1074201#1074201
last several post....
Note that thread: after looking back on some of Andy84 posts I believe his
trouble may be his router is a euro model and designated a RT N12-D and not a RTN12-D1.
Posted: Wed Apr 12, 2017 0:43 Post subject: Netgear R7000
Router:Netgear R7000
Firmware:04-06-2017-r31825
Previous:03-30-2017-r31791
Kernel:Linux 4.4.59 #1388 SMP Wed Apr 5 06:30:45 CEST 2017 armv7l
Status:Working.
Reset:No.
Errors:NTP does not work with dnsmasq unless IP is specified. For example time.windows.com does not resolve but 13.65.245.138 does.
Hi, can someone tell, please, if mobile broadband is working again?
Tried so many times, but always had to go back to 28600, the last which worked.
Would be kind, if I could get a response from so who tried it.
Thanks
Using R7000
Have you opened a ticket?
There is already one #5307 and still open
Once there was an answer from Kong
Changed 19 months ago by Kong
Resolution set to worksforme
Status changed from new to closed
Tested current build with Huawei E1750. It is wortking fine with basic config through webif.
Thus cannot reproduce it. If you have problems with a specific device, either supply a fix or a device for testig purposes.
Router: Linksys WRT320N
Firmware: dd-wrt.v24-31825_NEWD-2_K2.6_mini_wrt320n.bin
Previous: dd-wrt.v24-15962_NEWD-2_K2.6_mini_wrt320n.bin
Kernel: Linux 2.6.24.111 #31151 Thu Apr 6 00:06:34 CEST 2017 mips
Status: Working (PPPoE)
Reset: Yes
Errors:
(1) Setup/VLANs - disabling Gigabit to force 100mbps LAN port connection has no effect
(2) Setup/Basic Setup / Multiple DHCP Server - pressing "Add" button has no effect