Posted: Fri Dec 08, 2017 15:25 Post subject: Flash via TFTP
You can flash this router via TFTP using one of the 2 files. This has only been tested once, not by me. You should be able to upgrade via the webupgrade file for the 841ND v11. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
Posted: Thu Jul 19, 2018 17:18 Post subject: Re: Flash via TFTP
ian5142 wrote:
You can flash this router via TFTP using one of the 2 files. This has only been tested once, not by me. You should be able to upgrade via the webupgrade file for the 841ND v11.
Sorry, could I flash that .bin file directly via webflash (through firmware upgrade in the GUI)?
More than most likely the TP-Link firmware will give you an error code of 18005 if you try to flash my modified file, through the webGUI. If you flash it via TFTP, it should work though. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
Posted: Fri Jul 20, 2018 7:39 Post subject: Re: TFTP
ian5142 wrote:
More than most likely the TP-Link firmware will give you an error code of 18005 if you try to flash my modified file, through the webGUI. If you flash it via TFTP, it should work though.
I couldn't get the right timing to push the file. I've tried many times but seems nothing happened.
Or do I need to 30-30-30 reset before flashing via TFTP?
Posted: Thu Aug 02, 2018 3:33 Post subject: Re: Serial / TFTP
I flashed my router via TFTP, worked great! Thanks!
I merged the instructions from here and here to get it working. I ran the following steps:
1. Downloaded your firmware
2. Copied it to C:\TEMP and renamed the file to wr845nv1_tp_recovery.bin
3. Installed Tftpd32 with the tftpd64 installer
4. Connected a UTP-cable to a LAN port (not WAN)
5. Changed my laptop's LAN IP address to 192.168.0.66 with subnet mask 255.255.255.0
6. Ran Tftpd32, clicked "Browse" and browsed to C:\TEMP, selected the LAN interface with IP address 192.168.0.66, clicked "Show Dir", then clicked the wr845nv1_tp_recovery.bin file
7. On the router, powered off, pressed the Reset button, powered on, waited about 2 seconds, then clicked "Copy" on Tftpd32
8. Router flashed and rebooted itself, I browsed to http://192.168.1.1
9. Success!
Posted: Thu Aug 02, 2018 12:17 Post subject: Router identify
How does the router identify itself on the Router Status page?
You should be able to upgrade to a newer build using that router's webupgrade file. See the link in my signature. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
Posted: Fri Aug 03, 2018 0:37 Post subject: Re: Router identify
ian5142 wrote:
How does the router identify itself on the Router Status page?
Router Information System
Router Name DD-WRT
Router Model TP-Link TL-WR841ND v11
Firmware Version DD-WRT v3.0-r33772 std (11/16/17)
Kernel Version Linux 3.18.81 #2310 Thu Nov 16 06:11:31 CET 2017 mips
CPU
CPU Model Qualcomm Atheros QCA9533 ver 2 rev 1.0 (0x0160)
CPU Cores 1
CPU Features MIPS32r1 MIPS32r2 MIPS16
CPU Clock 650 MHz
Posted: Fri Aug 03, 2018 1:16 Post subject: Re: Router identify
ian5142 wrote:
You should be able to upgrade to a newer build using that router's webupgrade file. See the link in my signature.
Upgraded with this firmware. Here's the status after rebooting:
Router Information System
Router Name DD-WRT
Router Model TP-Link TL-WR841ND v11
Firmware Version DD-WRT v3.0-r36410 std (07/28/18)
Kernel Version Linux 3.18.116 #18741 Sat Jul 28 04:08:10 CEST 2018 mips
CPU
CPU Model Qualcomm Atheros QCA9533 ver 2 rev 1.0 (0x0160)
CPU Cores 1
CPU Features MIPS32r1 MIPS32r2 MIPS16
CPU Clock 650 MHz
i flushed the firmware and it worked great but there is a problem. sometimes i can't access any sites in my laptop. but after a restart it works fine again. i think it freezes time to time.
i flushed the firmware and it worked great but there is a problem. sometimes i can't access any sites in my laptop. but after a restart it works fine again. i think it freezes time to time.
I'm running r38840 on my TL-WR845N v1 and it's rock solid. Consider trying it.