Posted: Sun Sep 10, 2017 20:22 Post subject: Netgear R7500v2 w/ r33342
Router Model: Netgear R7500v2
Status: Flashed OK
Reset: Reset NVRAM, manually changed settings back
Errors:
ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin
qcom-dwc3-ssphy 110f8830.phy: cannot get HSIO settings from device node, using default values
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter
voltage drivers not compiled into kernel for phy (100f8830.phy 110f8830.phy 110f8800.phy 110f8800.phy) --> vddcx , v3p3 , v1p8
USB and Sata no longer automount.
Still have to force it to run the .rc_startup after mount, then I have to go into Services/USB and hit apply (after every boot)
I've had this error since 33080 build and I've seen a few people post error tickets and they get marked as invalid.
Still has USB problems, no automount, seems like a "timing" issue, as rmmod and insmod xhci-hcd corrects issue, could be a boot script issue.
-----
Tank you
EA8500
DD-WRT v3.0-r33342 std (09/09/17)
Linux 3.18.70 #177 SMP PREEMPT Fri Sep 8 01:17:06 CEST 2017 armv7l
Tis working ok ...
Might have had a httpd crash couple times but didn't stay down over few seconds.
Probably I done something it didn't like... I'm really just goofin around anyways.
Running on a WAP (WAN disabled) with ovpn server + ovpn client.
Port 1, 2, 5, ath0 on main network just WAP & switch.
Port 3, 4, ath1 on restricted network via br1.
Entire br1 DHCP range is set in PBR so all clients connected to it go thru the tunnel...
.... but for a couple with static leases set outside of br1 DHCP range.
2GB FAT32 flash dr setup on SAMBA share all good and yea she mounts just fine after reboot.
Had no real problems --- all I'm doing seems working good on the EA8500
Haven't done much with the wireless or QOS but r33338-09/08/17 (AFAICT'bout same as this) has
been running couple days on the main router without any problems.
Errors:
ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin
qcom-dwc3-ssphy 110f8830.phy: cannot get HSIO settings from device node, using default values
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter
voltage drivers not compiled into kernel for phy (100f8830.phy 110f8830.phy 110f8800.phy 110f8800.phy) --> vddcx , v3p3 , v1p8
How do you get these errors displayed? Does syslogd have to be enabled for this to work?
I am asking this since the dmesg command does not produce any output at all here.
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Mon Sep 11, 2017 8:49 Post subject:
none of those are actual "errors" to bother with anyway..our dmesg is always filled with crap spam that looks like a problem but isnt. those messages only been there forever. if he looked a little below he'd see the ath10k firmware gets loaded still (if it didnt ur radios wouldnt work) _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Router Model: TP-Link TL-WR2543
Firmware Version: DD-WRT 09-09-2017-r33342
Web upgrade: O.K.
Reset: Yes, 30/30/30
Status: Bad, Unusable.
Errors: Used as wifi repeater and devices do not see the AP created.
The virtual interface channel appears as unknown.
The LAN connection works well.
TP-Link WR841NDv9
r33342 uptime 3h now, no problems so far
flashed via gui, no reset.
WAN PPPoE with bridged dsl-modem, two wireless interfaces (one of them unbridged guest network with isolated clients), two dhcp-servers
How do you get these errors displayed? Does syslogd have to be enabled for this to work?
I am asking this since the dmesg command does not produce any output at all here.
Kind regards,
DAC324
syslogs and klogd
set up your ssh and log into your router then goto
/tmp/var/log
and there should be a temporary file called 'messages'
you can cat it or tail it or grep it, there is a dozen ways to read it.
I usually type in "cat /var/tmp/log/messages | less"
because less is more and more is less and strange penguins have odd humor.
Router: DIR-615 i1
Status: Good
Reset: Reset to defaults with flash procedure; erased NVRAM before and after flash
Errors: None
Router: TL-WDR3600 v. 1.5
Status: Buggy - Random Reboots
Reset: Reset to defaults with flash procedure; erased NVRAM before and after flash
Errors: Router is randomly rebooting. Flashed back to 33006, which is the last build for this router that doesn't cause random reboots.
