New Kong test build: DD-WRT 33435M - 2017/10/04

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3, 4, 5  Next
Author Message
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 12837
Location: Netherlands

PostPosted: Tue Oct 10, 2017 8:14    Post subject: Reply with quote
Rset by telnet/putty into your router and issue:
Code:
erase nvram && reboot


Then put your settings in manually

_________________
Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800/XR500: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
Sponsor
Battou62
DD-WRT Novice


Joined: 10 Oct 2017
Posts: 2

PostPosted: Tue Oct 10, 2017 13:37    Post subject: Reply with quote
<Kong> wrote:
Battou62 wrote:
Router Model: Netgear R6400

Firmware Version: DD-WRT v3.0-r33435M (10/08/17)
Kernel Version: Linux 4.4.89 #448 SMP Sun Oct 8 10:09:05 CEST 2017 armv7l

Upgraded: from 33010M v3 via dd-wrt web interface
Reset: Yes: erase nvram

Status: Up and running

Errors: Yes, QOS does not seem to be working correctly. According to dslreports speed test, upload is being limited correctly but download is not.


Disable Shortcut Forwarding Engine on Setup->Basic Setup page.


You da man, everything appears to be working properly now.
SinCalChewy
DD-WRT User


Joined: 09 Nov 2014
Posts: 314
Location: Bakersfield, CA

PostPosted: Tue Oct 10, 2017 15:17    Post subject: Reply with quote
Router: 2x Netgear R7000
Firmware: DD-WRT v3.0-r33435M kongac (10/08/17)
Previous: DD-WRT v3.0-r33010M kongac (09/19/17)
Kernel: Linux 4.4.89 #448 SMP Sun Oct 8 10:09:05 CEST 2017 armv7l
Status: Working, minus OpenVPN (looking into that now)
Reset: No, flashed via ddup
Errors: None thus far.

_________________

Deployed Routers:
Netgear R7800 - 1x build 46979
- Gateway (USB /w Entware, CAKE QoS)
Netgear R7000 - 3x build 46979
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1848
Location: Canada

PostPosted: Tue Oct 10, 2017 16:04    Post subject: Re: 5GHz band wl_1 disappears from r7000 settings Reply with quote
d0mini wrote:
Router Model: Netgear R7000

Firmware Version: DD-WRT v3.0-r33435M (10/08/17)
Kernel Version: Linux 4.4.89 #448 SMP Sun Oct 8 10:09:05 CEST 2017 armv7l

Upgraded: 33010M
Reset: flashed with factory defaults

Status: Up and running

Errors: Yes, 5 GHz band disappears.

Hey,

My wl_1 channel disappears from the router settings despite the channel still being available most of the time, similar to this thread: http://www.dd-wrt.com/phpBB2/viewtopic.php?p=939616. It's just not there, not under wireless settings or wireless status, as if the router lacked the functionality. I had previously set the then-present 5GHz band with an SSID and a WPA2 password. I'm not sure how long it took for it to disappear.

I've had this problem with previous releases, I hope it's possible to fix. In the meantime I will try restarting the router/setting to factory defaults and setting manual settings for the 5GHz channel if it surfaces again.

Thanks for all you do Kong and Brainslayer, you are both incredible individuals.



I didn't have issues with the wireless GUI BUT...

I too ran into a problem after loading "New" Build 33435 2017-Oct-08 on a Family's R7000 where radio WL1 (5Ghz) wasn't starting on reboot or power-up, so thanks to Kong for posting the correct code to disable/enable radios I added this script in Startup...

# After installing Build 33425 2017-Oct-08 wl1 radio doesn't start on bootup
# So restart both radios now
startservice radio_off_0 -f
startservice radio_off_1 -f
startservice radio_on_0 -f
startservice radio_on_1 -f

This fixes the issue on the Family R7000.

_________________
Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9

Off Site 1

R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4

Off Site 2

R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531


YAMon 3.4.6 | DNSCrypt-Proxy V2
d0mini
DD-WRT Novice


Joined: 10 Oct 2015
Posts: 21

PostPosted: Tue Oct 10, 2017 16:07    Post subject: Reply with quote
Thank you mac, that's very helpful Smile I'll try it when I get the chance.
SinCalChewy
DD-WRT User


Joined: 09 Nov 2014
Posts: 314
Location: Bakersfield, CA

PostPosted: Tue Oct 10, 2017 17:42    Post subject: Re: New Certs Reply with quote
kvoorhees wrote:
dragonC wrote:
dragonC wrote:
<Kong> wrote:
dragonC wrote:
My OpenVPN Server process fails launch.

I have it start under a Startup script (by directly launching /usr/sbin/openvpn with a config file). I can try to config it via the GUI and see if there's any difference.

Any one else has input on OpenVPN (server and/or client) in this build?

UPDATE: Same with GUI config -- OpenVPN process is not launching. Have to revert to previous working build for now.


Create new certs, same for freeradius, this is due to openssl upgrade. You can see this if you look at the syslog messages. tls_err...


Arr...thanks <Kong>. Let me give it a try.



Bad on my part --> I vaguely remember turning syslog off, coz I don't often monitor that. But occasional incidents like this is the reason we should have that enabled in the first place. Will report back once I give it a try.




New certs work. Thanks Kong


Do we have to generate all new client certs as well? What specifically do we need to update? Thanks!

I generated all new certs both server and client(s), and it's working just fine now. Not sure if that's what you had to do, but it works.

_________________

Deployed Routers:
Netgear R7800 - 1x build 46979
- Gateway (USB /w Entware, CAKE QoS)
Netgear R7000 - 3x build 46979
WillyTP
DD-WRT Novice


Joined: 03 Sep 2017
Posts: 11

PostPosted: Wed Oct 11, 2017 12:16    Post subject: Reply with quote
Hello everybody
Could please some RT-AC68U owner tell me if the 5GHz Led status is still broken?

Thanks!
falcon111
DD-WRT User


Joined: 22 Feb 2014
Posts: 76

PostPosted: Wed Oct 11, 2017 12:27    Post subject: Reply with quote
WillyTP wrote:
Hello everybody
Could please some RT-AC68U owner tell me if the 5GHz Led status is still broken?

Thanks!


Yes, it is.
bacon612
DD-WRT User


Joined: 09 Mar 2007
Posts: 82

PostPosted: Wed Oct 11, 2017 12:44    Post subject: Reply with quote
RT-AC68U
Kong 10/4 build

I'm also getting an issue where my clients can connect to 5GHz band on my 68u but the 5GHz band has disappeared from the wireless status page altogether. Though im connected. The GUI doesnt show any of my clients at all. Really bizzare.
blaser
DD-WRT Guru


Joined: 16 Jul 2006
Posts: 525

PostPosted: Thu Oct 12, 2017 10:36    Post subject: Reply with quote
bacon612 wrote:
RT-AC68U
Kong 10/4 build

I'm also getting an issue where my clients can connect to 5GHz band on my 68u but the 5GHz band has disappeared from the wireless status page altogether. Though im connected. The GUI doesnt show any of my clients at all. Really bizzare.


Mine is working fine with the latest Kong version

_________________
Netgear R9000 main router
RAX80 as AP
falcon111
DD-WRT User


Joined: 22 Feb 2014
Posts: 76

PostPosted: Thu Oct 12, 2017 21:21    Post subject: Reply with quote
mac913 wrote:
Kong has NTP Server IPs setup in the firmware, therefore you can leave the "Server IP/Name" blank.

Tried everything: empty NTP server name, 91.226.136.155, ntp4.stratum2.ru with server= and address= in DNSMasq, nothing helps. Router boots up, and not getting correct time, leaves all connected devices with no resolving, unless i disable dnscrypt.
It's pity, rather good build in all other aspects suffers from this errata.
As a temporary solution i've added "date 201710130000" to startup script, it solves the problem for now.
zfil
DD-WRT Novice


Joined: 12 Oct 2014
Posts: 31

PostPosted: Fri Oct 13, 2017 5:47    Post subject: Reply with quote
Router: R7000
Firmware: DD-WRT v3.0-r33435M kongac (10/08/17)
Kernel: Linux r7000 4.4.89 #448 SMP Sun Oct 8 10:09:05 CEST 2017 armv7l DD-WRT
Upgraded: from 33010M v3 via ddup --flash-remote http://www.desipro.de/ddwrt/K3-AC-Arm/dd-wrt.v24-K3_AC_ARM_STD.bin
Reset: no
Status: Error
Errors: router freeze after 2+ days uptime

I notice random freeze, I've tried to mitigate this by rebooting the router everyday to no effect

Code:

Oct 13 01:44:07 r7000 kern.err kernel: INFO: rcu_sched detected stalls on CPUs/tasks:
Oct 13 01:44:07 r7000 kern.err kernel:  1-...: (1 GPs behind) idle=111/140000000000000/0 softirq=15847341/15847342 fqs=6001
Oct 13 01:44:07 r7000 kern.err kernel:  (detected by 0, t=6002 jiffies, g=1580683, c=1580682, q=1695)
Oct 13 01:44:07 r7000 kern.info kernel: Task dump for CPU 1:
Oct 13 01:44:07 r7000 kern.info kernel: ledtool         R running      0 18232      1 0x00000002
Oct 13 01:44:07 r7000 kern.warn kernel: Backtrace:
Oct 13 01:44:07 r7000 kern.warn kernel: [<800ca0c0>] (vfs_write) from [<800ca918>] (SyS_write+0x44/0x84)
Oct 13 01:44:07 r7000 kern.warn kernel:  r8:76e050e0 r7:00000000 r6:00000000 r5:87b36640 r4:87b36640
Oct 13 01:44:07 r7000 kern.warn kernel: [<85ea7fa4>] (0x85ea7fa4) from [<00000000>] (  (null))
Oct 13 01:44:07 r7000 kern.warn kernel: Backtrace aborted due to bad frame pointer <10c5387d>
[...]
Oct 13 01:47:07 r7000 kern.err kernel: INFO: rcu_sched detected stalls on CPUs/tasks:
Oct 13 01:47:07 r7000 kern.err kernel:  1-...: (1 GPs behind) idle=111/140000000000000/0 softirq=15847341/15847342 fqs=24005
Oct 13 01:47:07 r7000 kern.err kernel:  (detected by 0, t=24007 jiffies, g=1580683, c=1580682, q=3537)
Oct 13 01:47:07 r7000 kern.info kernel: Task dump for CPU 1:
Oct 13 01:47:07 r7000 kern.info kernel: ledtool         R running      0 18232      1 0x00000002
Oct 13 01:47:07 r7000 kern.warn kernel: Backtrace:
Oct 13 01:47:07 r7000 kern.warn kernel: [<800ca0c0>] (vfs_write) from [<800ca918>] (SyS_write+0x44/0x84)
Oct 13 01:47:07 r7000 kern.warn kernel:  r8:76e050e0 r7:00000000 r6:00000000 r5:87b36640 r4:87b36640
Oct 13 01:47:07 r7000 kern.warn kernel: [<85ea7fa4>] (0x85ea7fa4) from [<00000000>] (  (null))
Oct 13 01:47:07 r7000 kern.warn kernel: Backtrace aborted due to bad frame pointer <10c5387d>
[...]
Oct 13 01:50:07 r7000 kern.err kernel: INFO: rcu_sched detected stalls on CPUs/tasks:
Oct 13 01:50:07 r7000 kern.err kernel:  1-...: (1 GPs behind) idle=111/140000000000000/0 softirq=15847341/15847342 fqs=42009
Oct 13 01:50:07 r7000 kern.err kernel:  (detected by 0, t=42012 jiffies, g=1580683, c=1580682, q=7641)
Oct 13 01:50:07 r7000 kern.info kernel: Task dump for CPU 1:
Oct 13 01:50:07 r7000 kern.info kernel: ledtool         R running      0 18232      1 0x00000002
Oct 13 01:50:07 r7000 kern.warn kernel: Backtrace:
Oct 13 01:50:07 r7000 kern.warn kernel: [<800ca0c0>] (vfs_write) from [<800ca918>] (SyS_write+0x44/0x84)
Oct 13 01:50:07 r7000 kern.warn kernel:  r8:76e050e0 r7:00000000 r6:00000000 r5:87b36640 r4:87b36640
Oct 13 01:50:07 r7000 kern.warn kernel: [<85ea7fa4>] (0x85ea7fa4) from [<00000000>] (  (null))
Oct 13 01:50:07 r7000 kern.warn kernel: Backtrace aborted due to bad frame pointer <10c5387d>
Oct 13 01:51:17 r7000 daemon.info dnsmasq-dhcp[7744]: DHCPREQUEST(br0) 192.168.0.110 a4:d1:8c:50:65:6c
Oct 13 01:51:17 r7000 daemon.info dnsmasq-dhcp[7744]: DHCPACK(br0) 192.168.0.110 a4:d1:8c:50:65:6c iPad-de-Anatole
Oct 13 01:53:07 r7000 kern.err kernel: INFO: rcu_sched detected stalls on CPUs/tasks:
Oct 13 01:53:07 r7000 kern.err kernel:  1-...: (1 GPs behind) idle=111/140000000000000/0 softirq=15847341/15847342 fqs=60013
Oct 13 01:53:07 r7000 kern.err kernel:  (detected by 0, t=60017 jiffies, g=1580683, c=1580682, q=9667)
Oct 13 01:53:07 r7000 kern.info kernel: Task dump for CPU 1:
Oct 13 01:53:07 r7000 kern.info kernel: ledtool         R running      0 18232      1 0x00000002
Oct 13 01:53:07 r7000 kern.warn kernel: Backtrace:
Oct 13 01:53:07 r7000 kern.warn kernel: [<800ca0c0>] (vfs_write) from [<800ca918>] (SyS_write+0x44/0x84)
Oct 13 01:53:07 r7000 kern.warn kernel:  r8:76e050e0 r7:00000000 r6:00000000 r5:87b36640 r4:87b36640
Oct 13 01:53:07 r7000 kern.warn kernel: [<85ea7fa4>] (0x85ea7fa4) from [<00000000>] (  (null))
Oct 13 01:53:07 r7000 kern.warn kernel: Backtrace aborted due to bad frame pointer <10c5387d>
[...]
Oct 13 01:56:07 r7000 kern.err kernel: INFO: rcu_sched detected stalls on CPUs/tasks:
Oct 13 01:56:07 r7000 kern.err kernel:  1-...: (1 GPs behind) idle=111/140000000000000/0 softirq=15847341/15847342 fqs=78017
Oct 13 01:56:07 r7000 kern.err kernel:  (detected by 0, t=78022 jiffies, g=1580683, c=1580682, q=13449)
Oct 13 01:56:07 r7000 kern.info kernel: Task dump for CPU 1:
Oct 13 01:56:07 r7000 kern.info kernel: ledtool         R running      0 18232      1 0x00000002
Oct 13 01:56:07 r7000 kern.warn kernel: Backtrace:
Oct 13 01:56:07 r7000 kern.warn kernel: [<800ca0c0>] (vfs_write) from [<800ca918>] (SyS_write+0x44/0x84)
Oct 13 01:56:07 r7000 kern.warn kernel:  r8:76e050e0 r7:00000000 r6:00000000 r5:87b36640 r4:87b36640
Oct 13 01:56:07 r7000 kern.warn kernel: [<85ea7fa4>] (0x85ea7fa4) from [<00000000>] (  (null))
Oct 13 01:56:07 r7000 kern.warn kernel: Backtrace aborted due to bad frame pointer <10c5387d>
[...]
Oct 13 01:59:07 r7000 kern.err kernel: INFO: rcu_sched detected stalls on CPUs/tasks:
Oct 13 01:59:07 r7000 kern.err kernel:  1-...: (1 GPs behind) idle=111/140000000000000/0 softirq=15847341/15847342 fqs=96021
Oct 13 01:59:07 r7000 kern.err kernel:  (detected by 0, t=96027 jiffies, g=1580683, c=1580682, q=15851)
Oct 13 01:59:07 r7000 kern.info kernel: Task dump for CPU 1:
Oct 13 01:59:07 r7000 kern.info kernel: ledtool         R running      0 18232      1 0x00000002
Oct 13 01:59:07 r7000 kern.warn kernel: Backtrace:
Oct 13 01:59:07 r7000 kern.warn kernel: [<800ca0c0>] (vfs_write) from [<800ca918>] (SyS_write+0x44/0x84)
Oct 13 01:59:07 r7000 kern.warn kernel:  r8:76e050e0 r7:00000000 r6:00000000 r5:87b36640 r4:87b36640
Oct 13 01:59:07 r7000 kern.warn kernel: [<85ea7fa4>] (0x85ea7fa4) from [<00000000>] (  (null))
Oct 13 01:59:07 r7000 kern.warn kernel: Backtrace aborted due to bad frame pointer <10c5387d>
[...]
Oct 13 02:02:07 r7000 kern.err kernel: INFO: rcu_sched detected stalls on CPUs/tasks:
Oct 13 02:02:07 r7000 kern.err kernel:  1-...: (1 GPs behind) idle=111/140000000000000/0 softirq=15847341/15847342 fqs=114024
Oct 13 02:02:07 r7000 kern.err kernel:  (detected by 0, t=114032 jiffies, g=1580683, c=1580682, q=19782)
Oct 13 02:02:07 r7000 kern.info kernel: Task dump for CPU 1:
Oct 13 02:02:07 r7000 kern.info kernel: ledtool         R running      0 18232      1 0x00000002
Oct 13 02:02:07 r7000 kern.warn kernel: Backtrace:
Oct 13 02:02:07 r7000 kern.warn kernel: [<800ca0c0>] (vfs_write) from [<800ca918>] (SyS_write+0x44/0x84)
Oct 13 02:02:07 r7000 kern.warn kernel:  r8:76e050e0 r7:00000000 r6:00000000 r5:87b36640 r4:87b36640
Oct 13 02:02:07 r7000 kern.warn kernel: [<85ea7fa4>] (0x85ea7fa4) from [<00000000>] (  (null))
Oct 13 02:02:07 r7000 kern.warn kernel: Backtrace aborted due to bad frame pointer <10c5387d>


Last edited by zfil on Fri Oct 13, 2017 6:39; edited 3 times in total
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1848
Location: Canada

PostPosted: Fri Oct 13, 2017 6:21    Post subject: Reply with quote
zfil wrote:
Router: R7000
Firmware: DD-WRT v3.0-r33435M kongac (10/04/17)
Kernel: Linux 4.4.89 #446 SMP Wed Oct 4 07:56:30 CEST 2017 armv7l
Upgraded: from 33010M v3 via ddup --flash-latest
Reset: no
Status: Error
Errors: router freeze after 2+ uptime

...
[/code]


For your R7000 the current Stable Build is newer dated 10/08/17 use this command to load it...

ddup --flash-remote http://www.desipro.de/ddwrt/K3-AC-Arm/dd-wrt.v24-K3_AC_ARM_STD.bin

You loaded the "TEST" Build with command... ddup --flash-latest

_________________
Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9

Off Site 1

R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4

Off Site 2

R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531


YAMon 3.4.6 | DNSCrypt-Proxy V2
zfil
DD-WRT Novice


Joined: 12 Oct 2014
Posts: 31

PostPosted: Fri Oct 13, 2017 6:37    Post subject: Reply with quote
mac913 wrote:

For your R7000 the current Stable Build is newer dated 10/08/17 use this command to load it...

ddup --flash-remote http://www.desipro.de/ddwrt/K3-AC-Arm/dd-wrt.v24-K3_AC_ARM_STD.bin

You loaded the "TEST" Build with command... ddup --flash-latest


my bad wrong cut and paste I did flash the latest build (updating my post to fix this)
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 12837
Location: Netherlands

PostPosted: Fri Oct 13, 2017 9:53    Post subject: Reply with quote
zfil wrote:
mac913 wrote:

For your R7000 the current Stable Build is newer dated 10/08/17 use this command to load it...

ddup --flash-remote http://www.desipro.de/ddwrt/K3-AC-Arm/dd-wrt.v24-K3_AC_ARM_STD.bin

You loaded the "TEST" Build with command... ddup --flash-latest


my bad wrong cut and paste I did flash the latest build (updating my post to fix this)


You could try to erase nvram from the command prompt and put your settings in manually.

_________________
Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800/XR500: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
Goto page Previous  1, 2, 3, 4, 5  Next Display posts from previous:    Page 4 of 5
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum