wnr3500L v2 ethernet connection "has been deactivated&q

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
View previous topic :: View next topic  
Author Message
kototmoto
DD-WRT Novice


Joined: 09 Feb 2019
Posts: 3
PostPosted: Wed Feb 20, 2019 16:24    Post subject: wnr3500L v2 ethernet connection "has been deactivated&q Reply with quote
Hello i used "erase linux" in dd-wrt and it bricked my router. Now i can not connect by LAN, so i connect to ttl and see:

Code:
CFE for WNR3500Lv2 version: v1.0.9
Build Date: Fri May 6 11:54:17 CST 2011
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
NFLASH Boot partition size = 524288(0x80000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.136
CPU type 0x19749: 480MHz
Tot mem: 131072 KBytes

Device eth0: hwaddr C4-04-15-0A-BB-E8, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Checking crc...Invalid boot block on disk
Device eth0 has been deactivated.
Device eth0: hwaddr C4-04-15-0A-BB-E8, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Start TFTP server
Reading :: Failed.: Interrupted
Found a AMD NAND flash with 2048B pages or 128KB blocks; total size 128MB
Decompressing...done




These lines are constantly repeated. When i press ctrl-C i can type tftpd, but i can not use lan on a router, because the router doesn't want to connect to my computer. Just burning yellow led.



What should I do to reinstall firmware on the router?
Back to top View user's profile Send private message
Sponsor
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 12921
Location: Netherlands
PostPosted: Wed Feb 20, 2019 16:43    Post subject: Reply with quote
Type help to see the available CFE commands.
Normally ifconfig is present to setup an interface
_________________
Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800/XR500: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
Back to top View user's profile Send private message
kototmoto
DD-WRT Novice


Joined: 09 Feb 2019
Posts: 3
PostPosted: Thu Feb 21, 2019 6:50    Post subject: Reply with quote
when I write "help", he answers me this:
Code:
Invalid command: "help"

command status=-1

After entering the command "ifconfig eth0 up" nothing happens and command "ifconfig eth0 -auto" does not work, writes that he doesn’t know what -auto is.
Back to top View user's profile Send private message
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum