Posted: Wed Nov 29, 2023 8:35 Post subject: New Build - 11/29/2023 - r54248
Welcome to Atheros r54248 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Wed Nov 29, 2023 10:15 Post subject:
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r54248 std (11/29/23)
Kernel Version Linux 3.18.140-d6 #186007 Wed Nov 29 07:17:15 +06 2023 mips
update: GUI r54203 > r54248
reset: NO
mode: Gateway/Running set up form my signature
status: Operational 1h+
errors: --->>
Now i dont see the MBO in the GUI(WEB Interface) but, nvram MBO values are there..
nvram show | grep mbo
wlan0_mbo=0
wlan0_mbo_cell_data_conn_pref=0
ok its hidden under the FT settings
Disable EAPOL Key Retries is missing from GUI...
HostApd config box is missing from GUI...
but i still can see theirs nvram values
i use browser in private mode(pale-moon) and browser cash is cleared on close so, its not a browser issue to blame....
Overall on 1043v2 whit single MIPS core, this build degraded any performance that was left...
WIFI is bad...
VPN performance is very bad.. (disabled/enable DCO same shit) it used to stamp on 1.2 MB/s now its half, even lower than this..(400-700k) no idea what's happened...reverted back to 53833 and VPN and WIFI are back to normal...sadly im following the current patches/fixes so, i had to upgrade again to 54248, although its a horrible build...(also did reset and manual rebuild, nothing helped..linux, win, phones all bad VPN performance and floating wifi speeds..)
Router Model Netgear R7800
Firmware Version DD-WRT v3.0-r54248 std (11/29/23)
Kernel Version Linux R7800 6.1.64 #56 SMP Wed Nov 29 03:43:33 +07 2023 armv7l
update: CLI r54203 > r54248
reset: NO
mode: Gateway/Running set up form my signature
status: Operational 1h+
errors: apart from the issues described above, that may co-exists on R7800 too...unit is operational...currently i dont have access to its GUI...Thanks BS and Team !
No idea about R7800 performance as im away ATM cant test anything..yet.. _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Last edited by Alozaros on Sun Dec 03, 2023 19:23; edited 5 times in total
MBO AP Capability
A new information element is added to the Beacon,Probe Response, Association Response and Re Association
Response Frames for 802.11ax APs to inform clients about MBO support.
MBO AP Capability
A new information element is added to the Beacon,Probe Response, Association Response and Re Association
Response Frames for 802.11ax APs to inform clients about MBO support.
I was also unsure if this works on none ax routers like the r7800.
It states "Limitations of MBO - All non-802.11ax access points are not supported.
it would be nice for some clarity on this.
Does DD-WRT support any ax routers yet? _________________ Netgear R7800 PPPoE Main Router
Network IPV4 - Isolated Vlan's with IoT Devices. Unifi AC-Pro x 3 AP's, Router Wi-Fi Disabled. OVPN Server With Paid Commercial Wireguard Client's. Gateway Mode, DNSMasq, Static Leases & DHCP, Pi-Hole DNS & Running Unbound.
No one can build you the bridge on which you, and only you, must cross the river of life!
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Wed Nov 29, 2023 14:04 Post subject:
dir-862L is not ax, it still has mbo option(dont use mbo anyway, bs forces mfp enabled with it and mfp breaks like half the clients out there..)
gui in wireless security is all broken, have to enable mbo then the "missing" stuff like hostapd conf box appears.. all ax settings still missing completely, i have a mt7915 and to even able ax it all has to be added (and guessed) manually into hostapd..
many of these recent new builds arent ready to be posted whatsoever.. _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Router/Version: Netgear V7500v2
Kernel: Linux 6.1.64 #56 SMP Wed Nov 29 03:43:33 +07 2023 arm
Previous/Reset: 54135 / No Reset
Mode: Gateway+AP, SFE Disabled, STP Disabled, Wifi 5(VANILLA)/2.4(VANILLA) Main+Guest(VAP), DNSMasq, USB(3.2, Ext2)/Entware, DNSCrypt, NAS/Samba, Static & DHCP, QoS (WAN)
Issues/Errors: Upgraded but noticed USB-related syslogs for disconnect during shutdown and identification and mounting during startup are missing (did soft reboot afterwards to confirm). Otherwise all seems to work normally.
Posted: Thu Nov 30, 2023 0:35 Post subject: Linksys EA8500 doesn't work
Flashed to this build and its now stuck in a reboot loop. Going to USB TTL this weekend to see what happened. Maybe get some logs. This router has been difficult from the get go from switching from Factory to DD-WRT and its being very temperamental on what updates it will boot with. This didn't fix it and probably made the issue worse since it bricks the unit instead.
Linksys E2100L
DD-WRT v3.0-r54248 std (11/29/23)
Linux 3.10.108-d11 #146528 Wed Nov 29 05:32:01 +06 2023 mips
GUI install over r54135
WAP + OVPN server
all worky ok
#
Linksys WRT160NL
DD-WRT v3.0-r54248 std (11/29/23)
Linux 3.10.108-d11 #146524 Wed Nov 29 05:26:56 +06 2023 mips
GUI install over r54135
WAP + OVPN server
all worky ok
Router/Version: Netgear WNR2000v3
File/Kernel: Previous/Reset: r18777
Mode/Status: bad
Issues/Errors: out of ram
This router has been broken almost since the beginning of it's support. For starters the antique r18777 build is the only one that runs on it. It won't even webflash from that build it must be flashed via telnetting into it from the command line.
Once flashed it will reboot and come up. And then within 3 minutes it will stop responding other than broadcasting the SSID. I believe that the router runs out of memory and then the http server and telnet server crash.
