WGR 614 v6 with 2Mbyte flash 8Mbyte ram

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8  Next
Author Message
swker
DD-WRT Novice


Joined: 26 Oct 2008
Posts: 8

PostPosted: Mon Nov 03, 2008 7:28    Post subject: Reply with quote
damn lol its useless for now (atlest) i wanted to use it as an ap
Sponsor
Roddly
DD-WRT Novice


Joined: 22 Nov 2008
Posts: 1

PostPosted: Sat Nov 22, 2008 5:30    Post subject: Reply with quote
I bought this as an impulse buy for 12 bucks and was one of the lucky ones to have the 2MB chip. Looking forward to having DD-WRT in the future as it is worthless to me at the moment.
Eko
DD-WRT Developer/Maintainer


Joined: 07 Jun 2006
Posts: 5771

PostPosted: Sat Nov 22, 2008 6:39    Post subject: Reply with quote
Roddly wrote:
I bought this as an impulse buy for 12 bucks and was one of the lucky ones to have the 2MB chip. Looking forward to having DD-WRT in the future as it is worthless to me at the moment.

If you ca get another one for 12$, buy it and send it to me. This is only way I can make it work with dd-wrt.
Hegemon
DD-WRT Novice


Joined: 21 Oct 2008
Posts: 10

PostPosted: Fri Nov 28, 2008 3:57    Post subject: Reply with quote
Eko wrote:
Roddly wrote:
I bought this as an impulse buy for 12 bucks and was one of the lucky ones to have the 2MB chip. Looking forward to having DD-WRT in the future as it is worthless to me at the moment.

If you ca get another one for 12$, buy it and send it to me. This is only way I can make it work with dd-wrt.

Check your PMs.
myacct
DD-WRT Novice


Joined: 08 Oct 2008
Posts: 18

PostPosted: Tue Dec 09, 2008 14:41    Post subject: Re: WGR 614 v6 with 2Mbyte flash 8Mbyte ram Reply with quote
I unsoldered the 1MB flash from Netgear WGR614v6 board, and replaced with a 2MB one (S29AL016D90TF102). The 2MB flash was pre-flashed the first 256k with Linksys WRT54Gv5's CFE (http://www.dd-wrt.com/dd-wrtv2/downloads/others/wrt54gv5%20flashing/CFE.bin) by a certain programmer before it was being soldered on. I guess this CFE should be working for Netgear WGR614v6 as well, because its hardware specification is very close to WRT54Gv5. However, after powered one, all LEDs are turned on, but not flickering; and I even get nothing from the series console. Looks that this CFE does not initialize the board at all.

Any other CFE can I try?
myacct
DD-WRT Novice


Joined: 08 Oct 2008
Posts: 18

PostPosted: Tue Dec 09, 2008 14:55    Post subject: Re: WGR 614 v6 with 2Mbyte flash 8Mbyte ram Reply with quote
Also attached the whole image of the previous 1MB flash dumped by the programmer. It is believed to be VxWorks.
Anybody interested in having a look?

myacct wrote:
I unsoldered the 1MB flash from Netgear WGR614v6 board, and replaced with a 2MB one (S29AL016D90TF102). The 2MB flash was pre-flashed the first 256k with Linksys WRT54Gv5's CFE (http://www.dd-wrt.com/dd-wrtv2/downloads/others/wrt54gv5%20flashing/CFE.bin) by a certain programmer before it was being soldered on. I guess this CFE should be working for Netgear WGR614v6 as well, because its hardware specification is very close to WRT54Gv5. However, after powered one, all LEDs are turned on, but not flickering; and I even get nothing from the series console. Looks that this CFE does not initialize the board at all.

Any other CFE can I try?


Sorry I deleted the attachement because it includes some private informations.


Last edited by myacct on Tue Dec 23, 2008 10:18; edited 1 time in total
Bl4ck
DD-WRT Novice


Joined: 09 Dec 2008
Posts: 8

PostPosted: Tue Dec 09, 2008 21:52    Post subject: Reply with quote
Mine 614v6 has flash chip with the markings

MX6063519
29LV800CTTC-90G
2P110800

And the "ram" module is "IC" made and

IC42S16400-7T6
A1469700N 0706

I am assuming that the Flash chip is 1mbit correct ?
If not and its the 2mbit is it possible to put the latest v24 micro edition using tftp ? or just flash the damn thing using the web browser based upload ?
Bl4ck
DD-WRT Novice


Joined: 09 Dec 2008
Posts: 8

PostPosted: Thu Dec 11, 2008 18:12    Post subject: Reply with quote
bump ? Sad
Luniz2k1
DD-WRT Guru


Joined: 04 Oct 2007
Posts: 1258
Location: Ohio USA

PostPosted: Thu Dec 11, 2008 18:24    Post subject: Reply with quote
Bl4ck wrote:
Mine 614v6 has flash chip with the markings

MX6063519
29LV800CTTC-90G
2P110800

And the "ram" module is "IC" made and

IC42S16400-7T6
A1469700N 0706

I am assuming that the Flash chip is 1mbit correct ?
If not and its the 2mbit is it possible to put the latest v24 micro edition using tftp ? or just flash the damn thing using the web browser based upload ?

29LV800CTTC-90G
8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
1MB Flash

This was already noted in previous posts in this topic.

_________________
(05/02/17) std - 31924
Linksys WRT400N
Buffalo WHR-G300N

Got OpenDNS?
Bl4ck
DD-WRT Novice


Joined: 09 Dec 2008
Posts: 8

PostPosted: Thu Dec 11, 2008 18:32    Post subject: Reply with quote
Luniz2k1 wrote:
Bl4ck wrote:
Mine 614v6 has flash chip with the markings

MX6063519
29LV800CTTC-90G
2P110800

And the "ram" module is "IC" made and

IC42S16400-7T6
A1469700N 0706

I am assuming that the Flash chip is 1mbit correct ?
If not and its the 2mbit is it possible to put the latest v24 micro edition using tftp ? or just flash the damn thing using the web browser based upload ?

29LV800CTTC-90G
8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
1MB Flash

This was already noted in previous posts in this topic.
thank you very much ;]
lostlamb
DD-WRT Novice


Joined: 03 Jan 2009
Posts: 3

PostPosted: Sat Jan 03, 2009 6:41    Post subject: Reply with quote
Is there any result?
myacct
DD-WRT Novice


Joined: 08 Oct 2008
Posts: 18

PostPosted: Fri Jan 09, 2009 13:57    Post subject: Reply with quote
See this:

http://www.dd-wrt.com/phpBB2/viewtopic.php?t=44439&highlight=wgr614v6
Cincinnatikid
DD-WRT Novice


Joined: 24 Feb 2009
Posts: 1

PostPosted: Tue Feb 24, 2009 22:55    Post subject: Reply with quote
Hi does 29LV800CTTC-90G = 1MB flash?
soulstace
DD-WRT Guru


Joined: 04 Aug 2007
Posts: 6427

PostPosted: Tue Feb 24, 2009 23:04    Post subject: Reply with quote
look up Laughing Wink
malibumaniac
DD-WRT Novice


Joined: 19 Mar 2009
Posts: 1

PostPosted: Thu Mar 19, 2009 18:04    Post subject: Reply with quote
Hi all,

Got a V6 with a 2MB flash, but im wondering when we get a flashable solution, so i dont have to unsolder the chip.. any idea?
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8  Next Display posts from previous:    Page 5 of 8
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum