Posted: Wed Feb 09, 2022 5:42 Post subject: New Build - 02/09/2022 - r48305
Welcome to Broadcom r48305 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• DNScrypt 1.95 can still be used in WebUIbut v2 (not compatible) requires Golang and thus Entware. See Trac ticket #6246.
• WDS does not work on Broadcom ARM devices (only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Try client or repeater modes, but YMMV.
• VAPs not working at bootare fixed, both unbridged (r40634) and bridged (r47822). Please test, removestartup commands.
• If startup scripts do not work from USB add delay (wait script), sleep 25 or try Administration -> Commands -> Save USB.
• Broadcom ARM devices if 5 GHz channels are missingvia Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot'.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT WAN: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & /tmp/.ipt. Misc: stracetcpdumpwireshark.
• Gremlins: reset & configure manually, not restore a backup. Reboot. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) and applicable configurations to reproduce.
Linksys E2500
DD-WRT v3.0-r48305 mega (02/09/22)
Linux 4.4.302 #14348 Wed Feb 9 03:48:04 +07 2022 mips
GUI install over r48218
'dd-wrt.v24-48305_NEWD-2_K3.x_mega.bin'
all good
Joined: 18 Mar 2014 Posts: 12879 Location: Netherlands
Posted: Wed Feb 09, 2022 10:49 Post subject:
Firmware Version: DD-WRT v3.0-r48305M Community Build (02/09/22)
Kernel Version: Linux 4.4.302 #1 SMP Wed Feb 9 07:01:34 CET 2022 armv7l
Upgraded from: DD-WRT v3.0-r48296M Community Build (02/05/22)
Reset: No not this time
Status: Up and running for 2 hours, basic setup as Gateway, static leases, Advanced routing, Port Forwarding, IPv4, 2.4 GHz with unbridged VAP and 5 GHz.
Running one WireGuard tunnel to Keepsolid, second WireGuard tunnel to other DDWRT router for site-to-site connection. Running third WireGuard tunnel to Oracle Cloud server.
OpenVPN client tested and working
Joined: 18 Mar 2014 Posts: 12879 Location: Netherlands
Posted: Wed Feb 09, 2022 10:53 Post subject:
Router Model: Netgear R6400v2, board_id: U12H332T
Firmware Version: DD-WRT v3.0-r48305M Community Build (02/09/22)
Kernel Version: Linux 4.4.302 #1 SMP Wed Feb 9 07:01:34 CET 2022 armv7l
Upgraded from: DD-WRT v3.0-r48296M Community Build (02/05/22)
Reset: No not this time
Status: Up and running for 2 hours, basic setup as Gateway, static leases, 2,4GHz and 5Ghz working, USB storage NAS working.
OpenVPN server working.
WireGuard server working with 8 clients (phones, Windows and two other routers for site-to-site setup).
Joined: 04 Jan 2007 Posts: 11564 Location: Wherever the wind blows- North America
Posted: Wed Feb 09, 2022 15:38 Post subject:
Router Model Netgear R7000
Firmware Version DD-WRT v3.0-r48305 std (02/09/22)
Kernel Version Linux 4.4.302 #5210 SMP Wed Feb 9 02:26:50 +07 2022 armv7l
The only thing I can come up with is GPIO 7 DMZ will turn on if DISABLE.
GPIO 6 will cause a FULL FACTORY RESET
GPIO 1 seems to be Power (when disabled it will flash)
Router: ASUS RT-AC3100
Firmware: Experimental asus_rt-ac3100-firmware.trx
WiFi Configuration: 2.4GHz VHT40 G,N; 5GHz VHT80 N,AC; WPA2-PSK
Wireguard site-site client;uPNP;SFE
No DNS, No DHCP, not 192.168.1.1 LAN address
Static IPv4 WAN address
Had to revert to r48141. LEDs were same as last build (indicative of WiFi not working and WAN not linking); GUI inoperative (access only via Ethernet LAN port); was able to get access to the ASUS "miniWeb" to upload r48141 with extended reset. Then uploaded backup config to restore operation.
Summary: router inoperable after upgrade and GUI not accessible (using Opera and Firefox). Router recoverable using ASUS long reset to emergency upload prior firmware.
Am I looking at having to revert back off of the Experimental builds? Too bad if so as performance has been excellent through build 48141.
Router/Version: ASUS RT-AC68U rev B1 (TM-AC1900)
File: asus_rt-ac68u-firmware.trx
Kernel: Linux 4.4.302 #5210 SMP Wed Feb 9 02:26:50 +07 2022 armv7l
Previous/Reset: Asus Stock / Yes, then reconfigure from scratch
Mode/Status: AP, uptime 28min
Issues/Errors: Working as configured.
Thank you BS and all of the other devs who help out to make this firmware great. _________________ ASUS RT-AC3100 AP Merlin 386.12_4
ASUS RT-AC68U Media Bridge/Merlin 386.12_4 (x2)
ASUS RT-AC68U AP r54604
ASUS RT-AC68U Gateway/AP r54604
Edgerouter-4, v2.0.9-hotfix7
Firmware: v3.0-r48305 std (02/09/22)
Router/Version: Netgear R7000 Kernel: Linux 4.4.302 #5210 SMP Wed Feb 9 02:26:50 +07 2022 armv7l
Previous: v3.0-r48296 std (02/05/22)
Mode/Status: AP wired and wireless / Up and running for 1 day
Reset: Soft boot before and after upgrade
Temperatures: CPU 58.6 °C / WL0 45.3 °C / WL1 50.4 °C
Issues/Errors: Nothing significant
Updated via webif. No 'nvram erase' this time, last one was in July 2018 (r36325).
Upload and Download speeds are to ISP spec (500/500 Mbps).
Current basic R7000 setup (subject to change of course):
- Static WAN IP
- Shortcut Forwarding Engine: CTF, Flow Acceleration: Disabled
- STP - Enabled
- IPv4 only, both WAN and LAN
- LAN DHCP Enabled
- Not currently forwarding any ports
- Wireless: AP, Regulatory Domain = CANADA, wl0 Mixed (ch. 6), wl1 AC/N-Mixed (ch. 36, VHT80), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- No custom scripts
- No: ttraf, Tor, VNC, Zabbix, VPN, Radius, OpenVPN
- No: UPnP, DMZ, QoS
- No: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7