WZR-HP-G300NH support

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Goto page Previous  1, 2, 3, ... 63, 64, 65  Next
Author Message
tweiyang11
DD-WRT Novice


Joined: 24 Dec 2007
Posts: 37
Location: Selangor, Malaysia

PostPosted: Sun Oct 04, 2009 13:02    Post subject: Reply with quote
I see i see... hmm.. i guess i should go for the linksys then...
btw.. even if dd-wrt is supported (the buffalo) .. it wont support usb printer sharing right?

_________________
You call this "broadband" ?? OH MY GOD...
Sponsor
jessenj
DD-WRT Novice


Joined: 15 Feb 2007
Posts: 11

PostPosted: Sun Oct 04, 2009 14:21    Post subject: Reply with quote
USB Printer sharing is not a feature of this unit. With DD-WRT, anything is possible, depending on what is supported with DD-WRT, but seeing as how the 300NH is not going to be supported by DD-WRT any time soon, its basically not worth even discussing.
beoba
DD-WRT Novice


Joined: 07 Nov 2009
Posts: 2

PostPosted: Sat Nov 07, 2009 15:03    Post subject: Reply with quote
I haven't had any problems with my WZR-HP-G300NH. The web admin interface is pretty bad, but once I got everything set up the hardware has been fantastic. All the more reason I'd like ddwrt on mine.
Slax
DD-WRT User


Joined: 10 Nov 2009
Posts: 50

PostPosted: Thu Nov 12, 2009 16:28    Post subject: Reply with quote
The platform is the same as dir-615 c1 but the wireless NIC is different. Once a port comes out for dir-615, i would be willing to brick my router for this great cause Laughing
aurora1982
DD-WRT Novice


Joined: 26 Nov 2009
Posts: 1

PostPosted: Thu Nov 26, 2009 11:04    Post subject: Reply with quote
beoba wrote:
I haven't had any problems with my WZR-HP-G300NH. The web admin interface is pretty bad, but once I got everything set up the hardware has been fantastic. All the more reason I'd like ddwrt on mine.


I've read a lot of reviews about this Buffalo router. Also a lot about performance but the only thing that nobody is speaking about is the speed between the USB-nas and a pc over utp (and maybe wifi)

Is there somebody with this router+usb-nas that can make a small read/write test between his pc over the gigabit ports to the usb-nas? I ask this because all other routers with this usb-nas feature are really slow, speeds around 4MB/sec...

Another question i have about this router is if it is possible to route one port directly to the internet so this you can get your IP directly from your ISP.

thanks allot !
Slax
DD-WRT User


Joined: 10 Nov 2009
Posts: 50

PostPosted: Sat Dec 12, 2009 7:34    Post subject: Reply with quote
Yes, you are right. The USB-NAS has a write speed of around 5.59MB/sec. I am not sure what you mean by get ip from isp. DMZ?
pikersan
DD-WRT Novice


Joined: 26 Dec 2009
Posts: 1

PostPosted: Sat Dec 26, 2009 4:20    Post subject: Looking to get DD-WRT on 4 of my routers... Reply with quote
I am on the hunt for someone to help me get DD-WRT on 4 of my WZR-HP-G300NH. I also bought the wireless N Bridge unit thinking I could use that to bridge the gap of the distance needed in my home. No wires so I need a repeater based type system. I have 1 main unit in router mode and the rest are in access point mode. But they dont support bridge repeater mode I found out after I bought 3 more of them.

So now I am going to buy a second Bridge unit to cover my issue but these other 3 units are sitting doing nothing. Would like to get wireless at 150mb/s everywhere in the house.

The nas performance I am getting was 8+ MB/s transfer.

If someone has a price on how much it would cost to build me a firmware to get DD-WRT working on it I am interested to know.
Slax
DD-WRT User


Joined: 10 Nov 2009
Posts: 50

PostPosted: Tue Dec 29, 2009 0:34    Post subject: Reply with quote
Yea, we should all chip in to send developers a router. Anyone else interested?
project_x
DD-WRT Novice


Joined: 29 Dec 2009
Posts: 2

PostPosted: Tue Dec 29, 2009 4:49    Post subject: Reply with quote
Sure I would be willing to help in anyway I can to DD-WRT to work on this router. Very Happy
coaxmetal
DD-WRT Novice


Joined: 30 Dec 2009
Posts: 10

PostPosted: Wed Dec 30, 2009 1:20    Post subject: Reply with quote
Looks like the WRZ-G300NH is included in the source code and has been for a while. I guess that doesn't mean much though since it is a different product (took me a bit to figure this out, posting it here to save others time).

http://svn.dd-wrt.com:8000/dd-wrt/changeset/12974

On the plus side, support for the DIR-825 was added in 13516, so maybe the wrz-hp-g300nh will be added soon. According to the wiki they both use the same cpu.

I can confirm that this router has 64mb, I opened mine up and it is 32Mx16. I doubt it has a 32 mb flash, but will be thrilled if it does (someone updated the hardware table yesterday).

I didn't want to take a soldering iron to the board (yet) so I can't confirm the cpu/wireless or flash numbers.
yaiba
DD-WRT Novice


Joined: 21 Dec 2009
Posts: 13

PostPosted: Wed Dec 30, 2009 6:23    Post subject: Reply with quote
I have serail on WRZ-HP-G300NH v1.65 JP
Here's a couple of things:

Code:

BUFFALO U-BOOT Ver 1.02
AP83--539 (ar9100) U-boot 0.0.12
64 MB
Memory Test (address line)
Memory Test start(0x00000000) end(0x04000000) size(67108864)
Data line test start:0x00000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0x00000000 len:0x4000000 pattern 0xAAAAAAAA 0x55555555
Fill test patnum:5
fill Pattern 5555AAAA  Writing...   Reading...
fill Pattern AAAA5555  Writing...   Reading...
fill Pattern 0000FFFF  Writing...   Reading...
fill Pattern FFFF0000  Writing...   Reading...
fill Pattern AAAAAAAA  Writing...   Reading...
Top of RAM usable for U-Boot at: 84000000
Reserving 250k for U-Boot at: 83fc0000
Reserving 256k for malloc() at: 83f80000
Reserving 44 Bytes for Board Info at: 83f7ffd4
Reserving 36 Bytes for Global Data at: 83f7ffb0
Reserving 128k for boot params() at: 83f5ffb0
Stack Pointer at: 83f5ff98
Now running in RAM - U-Boot at: 83fc0000
Dev ID2:2222
Name: AMD-SPANSION Flash id: 0x1227E, Size: 33554432 bytes.
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Memory Test
uboot use  83F5FFB0 - 84000000
Memory Test start(80000000) end(83F00000) size(03F00000)
Pattern 00000000  Writing...  Reading...
Memory Test OK
### buf_ver=[1.02] U-Boot Ver.=[1.02]
### build_date(env)=[Feb 16 2009 - 10:47:08] build_date(bin)=[Feb 16 2009 - 10:47:08]
ag7100_enet_initialize...
: cfg1 0xf cfg2 0x7114
rtl8366sr_phy_setup  ethUnit=0
Realtek 8366SR switch ID 0x8366
Realtek Greeen Ethernet Setup
eth0: 02:aa:bb:cc:dd:1a
eth0 up
: cfg1 0xf cfg2 0x7114
eth1: 02:aa:bb:cc:dd:1a
eth1 up
eth0  02:AA:BB:CC:DD:1A
, eth1  02:AA:BB:CC:DD:1A

Trying eth0
eth0 is duplex
eth0 link down
FAIL
Trying eth1
eth1 link down
FAIL

tftp server(receive) go, waiting:4[sec]
Trying eth1
eth1 link down
FAIL
Trying eth0
eth0 is duplex
eth0 link down
FAIL
Load address: 0x81f00000

TftpServer Timeout;
Trying eth0
eth0 is duplex
ag7100_check_link: _100BASET
dup 1 speed 100
CFG_PLL_FREQ=5
CFG_HZ=bebc200
cpu pll=1050
eth pll=1032
eth0 clk pll=13000a44
eth0 mii=12
eth0 cfg1=f
eth0 cfg2=7115
eth0 fcfg_0=1f1f00
eth0 fcfg_1=7ff0000
eth0 fcfg_2=fff
eth0 fcfg_3=780008
eth0 fcfg_4=3ffff
eth0 fcfg_5=3ffff
no file was loaded.
## Booting image at be060000 ...
   Image Name:   Linux Kernel Image
   Created:      2009-09-25  12:05:57 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    20615104 Bytes = 19.7 MB
   Load Address: 80002000
   Entry Point:  80200000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80200000) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

Linux version 2.6.15 (vc03021@mkitec-xen) (gcc version 3.4.4) #1 Fri Sep 25 20:43:01 JST 2009
flash_size passed from bootloader = 32
arg 1: console=ttyS0,115200
arg 2: root=31:03
arg 3: rootfstype=jffs2
arg 4: init=/sbin/init
arg 5: mtdparts=ar9100-nor0:256k(u-boot),128k(u-boot-env),1024k(uImage),31104k(rootfs),128k@32640k(ART),128k@32512k(properties)
arg 6: mem=64M
use [CONFIG_CMDLINE] = console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init mtdparts=ar9100-nor0:256k(uboot),128k(uboot_environ),1024k
(linux),31104k(rootfs),128k@32640k(ART),128k@32512k(user_property),32128k@384k(firmware) mem=64M
CPU revision is: 00019374
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init mtdparts=ar9100-nor0:256k(uboot),128k(uboot_environ),1024k(l
inux),31104k(rootfs),128k@32640k(ART),128k@32512k(user_property),32128k@384k(firmware) mem=64M
Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 512 (order: 9, 8192 bytes)
Using 200.000 MHz high precision timer.
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 62536k/65536k available (1698k kernel code, 2940k reserved, 337k data, 108k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
NET: Registered protocol family 16
SCSI subsystem initialized
AR7100 GPIOC major 0
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
HDLC line discipline: version $Revision: #1 $, maxframe=4096
N_HDLC line discipline registered.
mel_initsw initialized.
Serial: 8250/16550 driver $Revision: #1 $ 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x0 (irq = 19) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE compression module registered
NET: Registered protocol family 24
AR9100 FLASH DRIVER found device
  vendor 0x1   device-id 0x227e, 0x2222, 0x2201
FLASH ID: S29GL256N SIZE: (32 MB)
7 cmdlinepart partitions found on MTD device ar9100-nor0
Creating 7 MTD partitions on "ar9100-nor0":
0x00000000-0x00040000 : "uboot"
0x00040000-0x00060000 : "uboot_environ"
0x00060000-0x00160000 : "linux"
0x00160000-0x01fc0000 : "rootfs"
0x01fe0000-0x02000000 : "ART"
0x01fc0000-0x01fe0000 : "user_property"
0x00060000-0x01fc0000 : "firmware"
u32 classifier
    OLD policer on
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
ip_conntrack version 2.4 (512 buckets, 4096 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_time loading
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ar7100wdt_init: Registering WDT success
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 108k freed
Warning: unable to open an initial console.

Please press Enter to activate this console. watchdogd.c(24) watchdogd_main :WD:Start Watchdog Daemon
rc.c(324) VerifyParamsOfInit :x:create status sections
DoesItMatter
DD-WRT Guru


Joined: 10 May 2008
Posts: 1373
Location: Pacific North West, USA

PostPosted: Sat Jan 02, 2010 11:20    Post subject: Reply with quote
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=63820

See bottom of that post

Looks like it was just added in build 13525

direct download link on bottom of that post.

_________________
Evil or Very Mad Soylent Green Is People ! Evil or Very Mad
Twisted Evil =-=-=-=-=-=-=-=-=-=-= Twisted Evil
2x Asus RT-N16 - Asuswrt-Merlin 3.0.0.4.376.47
Belkin F7D3302 - Toastman Tomato USB VPN 1.28.7505
Linksys E3000 - Toastman Tomato USB VPN 1.28.7505
-------------------------
2x Buffalo WZR-HP-G300NH V1 - OpenWRT Chaos Calmer 42830 / Gargoyle 1.6.2
TP-Link WR1043ND V1.8 - OpenWRT Chaos Calmer 42830
2x Engenius ESR900 - Stock Firmware 1.3.0 / OpenWRT Chaos Calmer 42830
ERamseth
DD-WRT Novice


Joined: 06 Jan 2010
Posts: 34

PostPosted: Thu Feb 04, 2010 6:41    Post subject: Reply with quote
i have dd-wrt working on wzr-hp-g300nh as we speak. see here: http://www.dd-wrt.com/phpBB2/viewtopic.php?p=403960#403960
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 6081
Location: Dresden, Germany

PostPosted: Wed Feb 24, 2010 16:19    Post subject: Reply with quote
dd-wrt has now been official released for this type. right now we can just provide web upgrade images for buffalo devices for EU/US. buffalo doesn not want that we release flashable images for japanese routers at this time
_________________
one cigarette costs 2 minutes of your life.
one bottle of beer costs 4 minutes of your life.
one working day costs 8 hours of your life.

DD-WRT supported Concerts @ Bunker Dresden
03.10.2014 - Front 242 / Haujobb / Planet Myer Day
ERamseth
DD-WRT Novice


Joined: 06 Jan 2010
Posts: 34

PostPosted: Wed Feb 24, 2010 16:47    Post subject: Reply with quote
Great news.

I'll upgrade and test after work today!
Goto page Previous  1, 2, 3, ... 63, 64, 65  Next Display posts from previous:    Page 2 of 65
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum