Just flashed the firmware, and both LAN and WiFi worked as expected. Unfortunately PPPoE did not work at all.. No packets either way through WAN..
Back to stock for now then =(
Keep up the good work though!
Same for me too. Hope future releases will work.
Mine is V2000/2034 model.
Keep up the good work though!
Because problem with WAN on my router can somebody help me how to connect belkin router to second router I have, which has WAN connection.
Belkin's IP = 192.168.1.1 (all my devices connected)
SIemens Sx763 IP= 192.168.2.1 (connected to internet, no clients).
Posted: Wed Jan 19, 2011 19:03 Post subject: F5D8235-4v2 Support or NO Support
If i go to the first link it looks like it is supported but when i go to download the firmware its not listed at all! Please help as the factory firmware sucks!
Posted: Wed Jan 19, 2011 19:10 Post subject: Re: F5D8235-4v2 Support or NO Support
MMorris wrote:
If i go to the first link it looks like it is supported but when i go to download the firmware its not listed at all! Please help as the factory firmware sucks!
Posted: Thu Jan 20, 2011 1:40 Post subject: Re: F5D8235-4v2 Support or NO Support
law wrote:
MMorris wrote:
If i go to the first link it looks like it is supported but when i go to download the firmware its not listed at all! Please help as the factory firmware sucks!
Firmware is posted in this topic on page 4 by BrainSlayer. Look for it.
I seen that but dont see any atachments or links that i can see anyways! And from what i have read there are different version 2 devices?? Please someone help me find the link to the download and how do i check if my V2 device will have the the correct hardware in it as someone else with a ver2 said the network ports done work with the firmware!
You'll have to be logged in to see attachments in the forum.
From what others has reported here it looks like Belkin changed the version number of the router when the changed the switch ic.
v20xx = RTL8366RB for which dd-wrt works.
v21xx = RTL8366SR for which dd-wrt currently doesn't work.
You'll have to take this with a pinch of salt though, it is so far based on a limited number of user reports. _________________ Kernel panic: Aiee, killing interrupt handler!
You'll have to be logged in to see attachments in the forum.
From what others has reported here it looks like Belkin changed the version number of the router when the changed the switch ic.
v20xx = RTL8366RB for which dd-wrt works.
v21xx = RTL8366SR for which dd-wrt currently doesn't work.
You'll have to take this with a pinch of salt though, it is so far based on a limited number of user reports.
Ok i was able to get the pictures and file. But looks like i am out of luck as i opened the case and i have a chipset RTL8366SR Wich is V2110 on the box!
I hope this gets support soon as i cant stand the factory firmware as it is worthless!!
Well, for me it wasn't that the WAN wasn't working, it was that PPPoE wasn't... If I set it up as DHCP, it got an IP from my ISP, but since they require PPPoE for internet connectivity, my internet didn't work.
If I set it to PPPoE on the other hand, it just refused to connect at all.. Didn't even get an IP address.
Reverted firmware and connected with the exact same credentials, and everything worked fine.
Well, for me it wasn't that the WAN wasn't working, it was that PPPoE wasn't... If I set it up as DHCP, it got an IP from my ISP, but since they require PPPoE for internet connectivity, my internet didn't work.
If I set it to PPPoE on the other hand, it just refused to connect at all.. Didn't even get an IP address.
Reverted firmware and connected with the exact same credentials, and everything worked fine.
My mistake, I ment PPPoE, my ISP only works PPPoE. I reverted firmaware also but I miss some functionalities dd-wrt is offering, NAS, VPN etc....Belkins firmware is poor...
My setup is:
1. Siemens SX 763 in bridged mode (LAN IP 192.168.2.1)
2. Belkin with PPPoE connected to lan port on 1. (LAN IP 192.168.1.1) and all devices are connected to it. After updating to dd-wrt couldn't get WAN IP using PPPoE.
have you tried buluan's solution on page 7(i think ). I think he had the same problem?
And is your version v2034nv, thats how it says on my packaging box?
have you tried buluan's solution on page 7(i think ). I think he had the same problem?
And is your version v2034nv, thats how it says on my packaging box?
cheers
my belkin router is F5D8235sa4 & ver is 2034sa. can anyone please suggest me any firmware? I'm very novice here. please help me by providing a link using which i can upgrade/flash firmware. belkin firmware is too poor.
Well, for me it wasn't that the WAN wasn't working, it was that PPPoE wasn't... If I set it up as DHCP, it got an IP from my ISP, but since they require PPPoE for internet connectivity, my internet didn't work.
If I set it to PPPoE on the other hand, it just refused to connect at all.. Didn't even get an IP address.
Reverted firmware and connected with the exact same credentials, and everything worked fine.
My mistake, I ment PPPoE, my ISP only works PPPoE. I reverted firmaware also but I miss some functionalities dd-wrt is offering, NAS, VPN etc....Belkins firmware is poor...
My setup is:
1. Siemens SX 763 in bridged mode (LAN IP 192.168.2.1)
2. Belkin with PPPoE connected to lan port on 1. (LAN IP 192.168.1.1) and all devices are connected to it. After updating to dd-wrt couldn't get WAN IP using PPPoE.
Configure your Siemens for real bridge mode so that it doesn't do any NAT, so that you get your real ISP WAN IP on the LAN port of the Siemens.
Then you will also get the same IP on the WAN port of the Belkin and PPPoE should work.
You are now in some kind of half-bridged mode that dd-wrt can't handle, you are also double NAT-ing which will cause problems for you if you want to do port forwarding. _________________ Kernel panic: Aiee, killing interrupt handler!
@sayeed_992
you can try firmware BrainSlayer posted on page 4, and tell us how it works.
Ih you need to revert it you can do so with restore firmware LOM posted on page 7.
p.s. thanks BS and LOM for your contribution - great job!