I flashed to 12476 NEWD2 on my WRT600N V1.1 and I can only connect to the 5ghz network when it is set to mixed mode. The only other options are A and NA mode; when NA mode is selected I can see the network but I cannot connect to it. Currently in mixed mode my speed is limited to 54mbps.
Also, when the power settings are set to 82mw on both Wl0 and Wl1 the status page reports both as being 84mw. Setting the power to 83mw for Wl1 does nothing to change this.
I flashed to 12476 NEWD2 on my WRT600N V1.1 and I can only connect to the 5ghz network when it is set to mixed mode. The only other options are A and NA mode; when NA mode is selected I can see the network but I cannot connect to it. Currently in mixed mode my speed is limited to 54mbps.
Also, when the power settings are set to 82mw on both Wl0 and Wl1 the status page reports both as being 84mw. Setting the power to 83mw for Wl1 does nothing to change this.
Do you have WMM Support Enabled or not? It should be Enabled and you should have CTS Protection set to Auto. Now no more setting discussions. If you want more info PM me, but please try doing those things first. _________________ R7000 Kong vpn 23550-R01 (Main Router)
WRT610Nv2 converted E3000 vpnKong 21661 (RB)
WRT600N v1.1 BS std-nokaid 13637(5Ghz CB)(2.4Ghz AP)
WRT54G v5 BS micro 14684(RB)
Joined: 01 May 2009 Posts: 274 Location: San Jose, Ca
Posted: Mon Jul 13, 2009 23:56 Post subject:
just flash my 310N and is running fine with the newd-2 Mini build _________________ E3000 K2.6 Eko 16758 Mega
E3000 CB K2.6 EKO 16758 STD USB NAS
WRT610N V2 CB K2.6 Eko15337 STD Nokaid
WRT310N V2 CB K2.6 BS 15362 STD Nokaid
Joined: 01 May 2009 Posts: 274 Location: San Jose, Ca
Posted: Tue Jul 14, 2009 0:49 Post subject:
The build is nice! speeds are solid and the signal strength is great as well..give it a shot what do you have to lose? _________________ E3000 K2.6 Eko 16758 Mega
E3000 CB K2.6 EKO 16758 STD USB NAS
WRT610N V2 CB K2.6 Eko15337 STD Nokaid
WRT310N V2 CB K2.6 BS 15362 STD Nokaid
Well, curiosity killed..... my WRT350N. I flashed it with ND2, can't get it to recover.... I know have a project. _________________ WRT610N V2.0
Wrt54G V3.0
Wrt54G V7.0
Wrt54GS V7.0
Wrt350N V1.0
Wrt54gc
WNR834B V2
Flashed my wrt300n v1.1 and it works fine so far. Went from the stock linksys firmware, to a specific june mini build for the 300n v1.1 I had downloaded, then to this. In all of this the signal strength seemed consistent with stock.
I dont think the new driver gives a better signal, nor does tx power work. I did notice though that when router load was higher, signal strength was lower, and it got stronger when load decreased. Maybe there is truth to an under powered power supply. _________________ 1xWRT300N v1.1
Donation Gladly Provided
Well, curiosity killed..... my WRT350N. I flashed it with ND2, can't get it to recover.... I know have a project.
The 4th post in this thread could have warned ya. _________________ Read the forum announcements thoroughly! Be cautious if you're inexperienced.
Available for paid consulting. (Don't PM about complicated setups otherwise)
Looking for bricks and spare routers to expand my collection. (not interested in G spec models)
WRT600N v1.1 working fine here with newd-2 in AP mode. Clients can connect in 2.4 ghz wide channel (1+3) and in A mode. I haven´t tried in 5.8 N mode yet.
My other router, a WRT150N (bought refurbed in CompUSA Tampa FL for $10 bucks, what a steal) is still running Newd. It´s working fine as client bridge in 2.4 N.-
Has anyone had any experience flashing newd2 on WRT150N?