Posted: Tue Jul 09, 2013 11:23 Post subject: Re: Not all WL-342s are equal
Max Hopper wrote:
After sorting out the UART pins, the console revealed an Arcadyan OEM'ed WG7005-22 with 2X16MB storage.
N.B. Belkin also marketed this box as F5D8236-4_v2
Your RAM chips are 8MB ones so 16MB in total which also matches with what the 8236-4v2 has.
The flash chip is likely on the other side of the board, 8236-4v2 has only 2MB which makes it unsupportable. _________________ Kernel panic: Aiee, killing interrupt handler!
Posted: Sun Jan 26, 2014 2:01 Post subject: Re: New 21061 build not working
evgeny1978 wrote:
New 21061 build not working! To be more precise it is working right after reflashing. It stops working after first reboot, serial console shows that everything boots as usual (as I can see), but there is no network, PC can not acquire network address.
I had this exact problem also! I flashed from console to 21061 and couldnt get LAN activity after first reboot. I had to use the laptop to webflash 14896 and then the LAN ports worked.
21061 needs to be removed from download area until fixed!
Posted: Tue Feb 11, 2014 9:13 Post subject: Re: New 21061 build not working
Mosiah wrote:
I had this exact problem also! I flashed from console to 21061 and couldnt get LAN activity after first reboot. I had to use the laptop to webflash 14896 and then the LAN ports worked.
21061 needs to be removed from download area until fixed!
FYI for anyone wanting to flash a newer version than 14896 I have successfully flashed 23320 from this link.
Posted: Sun May 03, 2015 21:05 Post subject: just one option
Sorry to dig up this old thread.
I bought a wl342 at a flee market recently and thought it would serve well as additional router between my modem and the local network.
Installing dd-wrt gives me some trouble.
I have no multiple install/flash options. Just one.
Being :
Code:
Please choose the operation:
1: Load system code to SDRAM via TFTP
Running this option and uploading the dd-wrt image work fine until the dd-wrt kernel boots.
Code:
NET: Registered protocol family 17
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
searching for nvram
nvram size = 0
Broken NVRAM found, recovering it (Magic 20031985)
MAC_ADRH -- : 0x0000000c
MAC_ADRL -- : 0x43305277
MAC_ADRH -- : 0x0000000c
MAC_ADRL -- : 0x43305277
Ralink APSoC Ethernet Driver Initilization. v2.0 256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, Tx Ring = 256, Rx Ring = 256
MAC_ADRH -- : 0x0000000c
MAC_ADRL -- : 0x43305277
rt3052 access driver initialization.
List of all partitions:
1f00 192 mtdblock0 (driver?)
1f01 64 mtdblock1 (driver?)
1f02 64 mtdblock2 (driver?)
1f03 832 mtdblock3 (driver?)
1f04 2944 mtdblock4 (driver?)
1f05 64 mtdblock5 (driver?)
No filesystem could mount root, tried: squashfs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,4)
Rebooting in 1 seconds..
Posted: Thu May 28, 2015 0:13 Post subject: WIch version is the best for Encore ENHWI-N3 -
Hi, i have an Encore ENHWI-N3 - with RT3050F 16MB RAM 4MB Flash.
After installing the last build it works until i made changes on the config... like the password, then it crashes.
Do someone know which is the best build for this one?
Thanks a lot!
JP
You'll excuse me, I'm not sure with precision what are serial pin to be welded on the board. I've Posted photos here. Could you give me a confirmation of what are the serial pins ?
