Belkin F5D8235 Bad Magic Number

Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware
Author Message
Brainiac
DD-WRT Novice


Joined: 28 Jul 2009
Posts: 2

PostPosted: Tue Jul 28, 2009 10:54    Post subject: Belkin F5D8235 Bad Magic Number Reply with quote
after update fail i manage to brick my router
i manage to connect a serial cable to uart interface
and i get :

Quote:
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
5: Load ucos code to SDRAM via TFTP.
0

3: System Boot system code via Flash.
## Booting image at bc450000 ...
Bad Magic Number,23207369


I tried to upload via tftp firmvare put i stil get error
entering option 4 and printenv i get :

Quote:
### main_loop: bootcmd="tftp"
RT2880 # printenv
bootcmd=tftp
bootdelay=3
baudrate=57600
ethaddr="00:AA:BB:CC:DD:10"
preboot=echo;echo
ramargs=setenv bootargs root=/dev/ram rw
addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmas
k):$(hostname):$(netdev):off
addmisc=setenv bootargs $(bootargs) console=ttyS0,$(baudrate) ethaddr=$(ethaddr)
panic=1
flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr)
kernel_addr=BFC40000
u-boot=u-boot.bin
load=tftp 8A100000 $(u-boot)
u_b=protect off 1:0-1;era 1:0-1;cp.b 8A100000 BC400000 $(filesize)
loadfs=tftp 8A100000 root.cramfs
u_fs=era bc540000 bc83ffff;cp.b 8A100000 BC540000 $(filesize)
test_tftp=tftp 8A100000 root.cramfs;run test_tftp
ethact=Eth0 (10/100-M)
filesize=374138
fileaddr=8A800000
ipaddr=192.168.1.1
serverip=192.168.1.2
autostart=no
bootfile=firmware.tftp
stdin=serial
stdout=serial
stderr=serial

Environment size: 853/65532 bytes
RT2880 #




please advise
Sponsor
natan_berlin
DD-WRT Novice


Joined: 31 Jul 2009
Posts: 1

PostPosted: Fri Jul 31, 2009 4:30    Post subject: Reply with quote
Hi,
I had the same thing...
Remember when you upload to check if the firmware starts with the required magic number, this can be done using a Hex editor cut all the data up until the hex value of:

27 05 19 56

and thats it it should work ;)

BTW, which image are you trying to upload? I managed to use the ECB-9750 (9500) it boots up fine but only gives limited support Razz
I would love to start an organized disc. about this model Smile
Brainiac
DD-WRT Novice


Joined: 28 Jul 2009
Posts: 2

PostPosted: Fri Jul 31, 2009 8:08    Post subject: That did the job :) Reply with quote
That did the job Smile
Thank you very much .


I'm waiting a dd-wrt working firmware for my Belkin v 1 :)

Firmware v19 from Belkin, after editing firmware it works .


natan_berlin wrote:
Hi,
I had the same thing...
Remember when you upload to check if the firmware starts with the required magic number, this can be done using a Hex editor cut all the data up until the hex value of:

27 05 19 56

and thats it it should work ;)

BTW, which image are you trying to upload? I managed to use the ECB-9750 (9500) it boots up fine but only gives limited support Razz
I would love to start an organized disc. about this model Smile
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7463
Location: Dresden, Germany

PostPosted: Sun Dec 26, 2010 9:48    Post subject: Reply with quote
v2 is now supported in my internal sourcetree (and tested). v1 is not yet supported, since i dont have the device
_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum