Is it because the router has "only" 2MB of flash space?
In one post he (Brainslayer) says that he could port if the router has 16MB of RAM but another one says, that it's just not possible.
And why need vxWorks less space than DD-WRT?
Greetz
I have returned it and bought it from 3 different stores and keep getting 1.5.
Now we are stuck with this one.
As davidgrudek, I have a v1.5. I couldn't choose it because the version number isn't written on the box.
I'm obliged to keep it because the seller doesn't take a device with an opened box.
A very very minimal version of the DD-WRT firmware would be enough of the moment we have the opportunity to reserve IP addresses with DHCP (the official firmware doesn't). Please Brainslayer.
Joined: 22 Jun 2008 Posts: 2440 Location: Am now Dark_Shadow
Posted: Tue Feb 09, 2010 18:32 Post subject:
Turboloader wrote:
Is it because the router has "only" 2MB of flash space?
In one post he (Brainslayer) says that he could port if the router has 16MB of RAM but another one says, that it's just not possible.
And why need vxWorks less space than DD-WRT?
Greetz
Yes, as I recall the Atheros drivers are much larger than broadcom, so micro would be too larger to fit. _________________ The New Me
Sorry for doublepost.
1 question.
If I would find a way to make a "SD mod" for the WRT54G2. (No currently I haven't.)
Would one of you make a Firmware for this?
Mount the SD card as / would make no problems, wouldn't it?
As I read about SD mods for the old WRT54G I thought this would be a solution.
Greetz
CPU: WRT54G2. Processor #0.
Memory Size: 0x1000000. BSP version 1.0.
/fl/ - Volume is OK
Detect: eth wan(ae0) has been loaded to MUX layer
Detect: eth lan(ae1) has been loaded to MUX layer
pingLog.txt exist.
tracertLog.txt exist.
-> Http Server Start!
DHCP server started.
Dhcps_IpStart=192.168.101.100
Dhcps_IpEnd=192.168.101.149
temp =snmk=255.255.255.0:rout=192.168.101.6:dnsv=192.168.101.6:maxl=3600:dfll=86400
can't get ifpWAN | ifpLAN
DMZ disable
remote management disable
Filter Internet NAT Redirection disabled!!!
FTP ALG registered with NAT
RTSP ALG registered with NAT
H323 ALG registered with NAT
Msn ALG registered with NAT
SNMP ALG registered with NAT
NAT configuration and initialization complete!
PPPOE init......seccess
L2TP init......seccess
PPTP init......seccess
APCFG task id 80c3a350
[system is runing for 5 seconds] MSG_WAN_SHOULD_START
WAN TYPE:DHCP
usrDhcpcStart Start...
usrDhcpcStart End
sysWlanInit ...
wlan: mac acl policy registered
ag7240MemInit: allocated, dmabuf=0x80a7dda0, buffend = 80be99a4
wifi0: Atheros 9285: irq=66 hw_base=0x0xb0000000
check PIN ...
get pin from broaddata...
Reading Flash
Setting the IP address
AP_IPADDR=192.168.101.6
Bridge IP Address: 192.168.101.6
Entering Task Loop
LLTD: wireless interface argument is ath0.
Start Create MEM Drv to LLTD ico
AP_AUTOSTART=1
Automatic WLAN start!
sending message 80a50f70,10
Starting WLAN !!!!
AP_ENABLE=1
ATH_COUNTRYCODE=840
ieee80211_end_load: load done
ath0 end flag = 0x00028802
default
default
default
IEE80211-FREQ IOCTL 0,0,0
WLAN IOCTL AP_CHMODE=11G=11G=11G=1003
IEE80211-MODE IOCTL 1,11G,4
set mode 3,65535,6
set mode consistency pass 196608
set mode retv 0
Please press Enter to activate this console. gpio-buttons driver version 0.1.1
BusyBox v1.13.4 (2009-07-18 12:30:44 EEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
KAMIKAZE (bleeding edge, r16889) -------------------
* 10 oz Vodka Shake well with ice and strain
* 10 oz Triple sec mixture into 10 shot glasses.
* 10 oz lime juice Salute!
---------------------------------------------------
root@OpenWrt:/# ls
bin etc init lib proc root sys usr www
dev home jffs mnt rom sbin tmp var
root@OpenWrt:/# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@OpenWrt:/# ifconfig -a
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Does anyone know if it is possible to jtag into these routers? I have tried but haven't had any luck. From what i can tell the Atheros AR7240 chip isn't supported in any of the jtag revisions. I have several of the 1.5 units that have various issues. I know they dont support dd-wrt, but i would like to fix them if possible. Thanks in advance.