KONG testbuild DD-WRT v3.0-r37630M kongac (11/12/18)

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Author Message
acdcnow
DD-WRT Novice


Joined: 21 Oct 2018
Posts: 6

PostPosted: Tue Nov 13, 2018 12:21    Post subject: KONG testbuild DD-WRT v3.0-r37630M kongac (11/12/18) Reply with quote
Kong's DD-WRT test build v3.0-r37630M kongac (11/12/18 ) has been released: http://desipro.de/ddwrt/K3-AC-Arm/TEST/

Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:

This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29440_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
Sponsor
@m0eb@
DD-WRT User


Joined: 26 Dec 2015
Posts: 289

PostPosted: Tue Nov 13, 2018 14:15    Post subject: Netgear R6400v2 with board xxxx30 Reply with quote
Router: R6400v2 [OTP]
Firmware: DD-WRT v3.0-r37630M kongac (11/12/18 )
Kernel: Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
Status: Browser upgrade over r37015M
Reset: No
Errors: None

Router up for around 30 mins with no noticeble change in performance over the r37015M

Noticed a nominal improvement in the 5GHz SSID. OpenDNS, OpenVPN working as expected. LAN ports separated into OpenVPN and OpenDNS.

Have not tried out VAP etc.

Since OP does not mention what is new in this version, unsure what new stuff needs to be checked or tested. Would be willing to put my router to test if advised what to do

Edit/Add:
1. No unexpected warnings or errors on syslog
2. et robowr commands are behaving differently. I am an absolute moron as far as this command goes ... but I keep playng with this. I am seeing different responses now. I was able to get all LAN port LEDs to red without effecting the WAN LED.

_________________
PROFESSIONAL STUDENT
my.Mistakes my.Learning ... provided I have the patience & persistence to learn
Alozaros
DD-WRT Guru


Joined: 16 Nov 2015
Posts: 6410
Location: UK, London, just across the river..

PostPosted: Tue Nov 13, 2018 15:17    Post subject: Reply with quote
Router Model Netgear R7000
Firmware Version DD-WRT v3.0-r37630M kongac (11/12/1Cool
Kernel Version Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l

update: ddup 37015 > 37630
reset: NO
status: Operational
errors: hmm nothing yet, still testing...

_________________
Atheros
TP-Link WR740Nv1 ---DD-WRT 55179 WAP
TP-Link WR1043NDv2 -DD-WRT 55303 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55460 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55460 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55363 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
bushant
DD-WRT Guru


Joined: 18 Nov 2015
Posts: 2029

PostPosted: Wed Nov 14, 2018 0:14    Post subject: Reply with quote
Netgear R6200V2
dd-wrt.v24-K3_AC_ARM_STD.bin = 37630
previous 36840
Errors None
Usual PIA to upgrade-Brick/tftp 24170/reset/webgui upgrade-37630/reinstall settings
Repeater bridge <> R7800
Working Thanks <Kong>!

_________________
Forum Guide Lines (with helpful pointers about how to research your router, where and what firmware to download, where and how to post and many other helpful tips!)
How to get help the right way

Before asking for help - Read the forum guidelines AND Upgrade DD-WRT!
Adblock by eibgrad + Blocklist Collection
eywong
DD-WRT User


Joined: 21 Jul 2010
Posts: 120
Location: USA

PostPosted: Wed Nov 14, 2018 2:54    Post subject: Asus RT-AC68U A1 Reply with quote
Router: Asus RT-AC68U (H/W Ver: A1)
Firmware: DD-WRT v3.0-r37630M kongac (11/12/18)
Previous: DD-WRT v3.0-r37015M kongac (09/23/18)
Kernel: Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
Previous: Linux 4.4.157 #603 SMP Sun Sep 23 01:10:11 CEST 2018 armv7l
Status: ok
Reset: no (ddup --flash-latest)
Errors: no
Uptime: 7:23

wl0: AP / NG-Mixed / Ch 11
Channel Width: 20 MHz
wl1: AP / AC/N-Mixed / Ch 52 + 54
Channel Width: Wide VHT80 (80 MHz)
Extension Channel: lower lower
DHCP Server: Enabled - Running
Static Leases: 4 hardwired NAS, 1 wireless printer
NTP Client: Enable
Server IP/Name: us.pool.ntp.org
IPv6: Disable
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14125
Location: Texas, USA

PostPosted: Wed Nov 14, 2018 3:11    Post subject: Re: Netgear R6400v2 with board xxxx30 Reply with quote
@m0eb@ wrote:
Router: R6400v2 [OTP]
Firmware: DD-WRT v3.0-r37630M kongac (11/12/18 )
Kernel: Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
Status: Browser upgrade over r37015M
Reset: No
Errors: None

Router up for around 30 mins with no noticeble change in performance over the r37015M

Noticed a nominal improvement in the 5GHz SSID. OpenDNS, OpenVPN working as expected. LAN ports separated into OpenVPN and OpenDNS.

Have not tried out VAP etc.

Since OP does not mention what is new in this version, unsure what new stuff needs to be checked or tested. Would be willing to put my router to test if advised what to do

Edit/Add:
1. No unexpected warnings or errors on syslog
2. et robowr commands are behaving differently. I am an absolute moron as far as this command goes ... but I keep playng with this. I am seeing different responses now. I was able to get all LAN port LEDs to red without effecting the WAN LED.


Feel free to peruse through the log (600+ revisions is a LOT to pinpoint what affected Broadcom-ARM builds):

https://svn.dd-wrt.com/log/?rev=37630&stop_rev=37016&limit=615

BUT, I believe it's mostly kernel updates....
Bernadoe
DD-WRT User


Joined: 03 Dec 2014
Posts: 217

PostPosted: Wed Nov 14, 2018 10:22    Post subject: Reply with quote
Router: Netgear R7000
Firmware: DD-WRT v3.0-r37630M kongac (11/12/2018)
Kernel: Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
Status: Working
Reset: No
Previous: 37015M
Errors: No

CPU Temperature : CPU 55.2 °C / WL0 46.0 °C / WL1 50.2 °C

Working very well :
Router mode : DHCP
SFE Enable
STP Enable
DNSMasq
Encrypt DNS
Cache DNSSEC data
Validate DNS Replies (DNSSEC)
Local DNS
No DNS Rebind
Query DNS in Strict Order
SPI Firewall
Usb
Nas, MiniDLNA, Samba, JFFS2,
MAC Filter
wl0, wl1
Vpn (OpenVPN Client)

Kong and BS: Thanks for all your good work!

without VPN



with VPN
[/URL]
hurleyp
DD-WRT User


Joined: 10 Sep 2009
Posts: 425
Location: Ottawa, Ontario, Canada

PostPosted: Thu Nov 15, 2018 13:52    Post subject: Reply with quote
Router/Version: Netgear R7000
Firmware: v3.0-r37630M kongac (11/12/18 )
Kernel: Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
Previous: v3.0-r36840M kongac (09/03/18 )
Mode/Status: Up and runnig for 1 day
Reset: Soft boot before and after ddup
Issues/Errors: None

Upgraded via "ddup --flash-latest". No 'erase nvram' this time.

It looks like a new version is available already. Smile

The temperatures are good: CPU 55.8 °C / WL0 44.5 °C / WL1 47.5 °C (The R7000 is wall-mounted.)

Current basic R7000 setup (subject to change of course):
- SFE - On
- STP - On
- Static WAN IP
- LAN DHCP Enabled
- IPv4 only
- Encrypt DNS disabled
- Wireless: Regulatory Domain = UNITED_STATES, wl0 Mixed (ch. 1), wl1 NA-Mixed (ch. 161 + 159), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- NO: ttraf, VNC, Zabbix, VPN, Radius, OpenVPN
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware

_________________
Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
@m0eb@
DD-WRT User


Joined: 26 Dec 2015
Posts: 289

PostPosted: Sun Nov 18, 2018 4:35    Post subject: Reply with quote
Have used this extensively from my earlier comment till now. Zero issues faced.

Now trying to understand what's new in the later build, and then switching over to that.

This build is very stable for the R6400v2-OTP. Haven't tried VAP etc, which seems to be covered in the next build

_________________
PROFESSIONAL STUDENT
my.Mistakes my.Learning ... provided I have the patience & persistence to learn
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14125
Location: Texas, USA

PostPosted: Sun Nov 18, 2018 19:01    Post subject: Reply with quote
The 11/14 build mainly was to fix the detection algorithm for the R7000P.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum