Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29440_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
Posted: Tue Nov 13, 2018 14:15 Post subject: Netgear R6400v2 with board xxxx30
Router: R6400v2 [OTP]
Firmware: DD-WRT v3.0-r37630M kongac (11/12/18 )
Kernel: Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
Status: Browser upgrade over r37015M
Reset: No
Errors: None
Router up for around 30 mins with no noticeble change in performance over the r37015M
Noticed a nominal improvement in the 5GHz SSID. OpenDNS, OpenVPN working as expected. LAN ports separated into OpenVPN and OpenDNS.
Have not tried out VAP etc.
Since OP does not mention what is new in this version, unsure what new stuff needs to be checked or tested. Would be willing to put my router to test if advised what to do
Edit/Add:
1. No unexpected warnings or errors on syslog
2. et robowr commands are behaving differently. I am an absolute moron as far as this command goes ... but I keep playng with this. I am seeing different responses now. I was able to get all LAN port LEDs to red without effecting the WAN LED. _________________ PROFESSIONAL STUDENT my.Mistakes ∝ my.Learning ... provided I have the patience & persistence to learn
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Tue Nov 13, 2018 15:17 Post subject:
Router Model Netgear R7000
Firmware Version DD-WRT v3.0-r37630M kongac (11/12/1
Kernel Version Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
update: ddup 37015 > 37630
reset: NO
status: Operational
errors: hmm nothing yet, still testing... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Posted: Wed Nov 14, 2018 2:54 Post subject: Asus RT-AC68U A1
Router: Asus RT-AC68U (H/W Ver: A1)
Firmware: DD-WRT v3.0-r37630M kongac (11/12/18)
Previous: DD-WRT v3.0-r37015M kongac (09/23/18)
Kernel: Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
Previous: Linux 4.4.157 #603 SMP Sun Sep 23 01:10:11 CEST 2018 armv7l
Status: ok
Reset: no (ddup --flash-latest)
Errors: no
Uptime: 7:23
Joined: 08 May 2018 Posts: 14247 Location: Texas, USA
Posted: Wed Nov 14, 2018 3:11 Post subject: Re: Netgear R6400v2 with board xxxx30
@m0eb@ wrote:
Router: R6400v2 [OTP]
Firmware: DD-WRT v3.0-r37630M kongac (11/12/18 )
Kernel: Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
Status: Browser upgrade over r37015M
Reset: No
Errors: None
Router up for around 30 mins with no noticeble change in performance over the r37015M
Noticed a nominal improvement in the 5GHz SSID. OpenDNS, OpenVPN working as expected. LAN ports separated into OpenVPN and OpenDNS.
Have not tried out VAP etc.
Since OP does not mention what is new in this version, unsure what new stuff needs to be checked or tested. Would be willing to put my router to test if advised what to do
Edit/Add:
1. No unexpected warnings or errors on syslog
2. et robowr commands are behaving differently. I am an absolute moron as far as this command goes ... but I keep playng with this. I am seeing different responses now. I was able to get all LAN port LEDs to red without effecting the WAN LED.
Feel free to peruse through the log (600+ revisions is a LOT to pinpoint what affected Broadcom-ARM builds):
Router: Netgear R7000
Firmware: DD-WRT v3.0-r37630M kongac (11/12/2018)
Kernel: Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
Status: Working
Reset: No
Previous: 37015M
Errors: No
CPU Temperature : CPU 55.2 °C / WL0 46.0 °C / WL1 50.2 °C
Working very well :
Router mode : DHCP
SFE Enable STP Enable
DNSMasq
Encrypt DNS
Cache DNSSEC data
Validate DNS Replies (DNSSEC)
Local DNS
No DNS Rebind
Query DNS in Strict Order
SPI Firewall
Usb
Nas, MiniDLNA, Samba, JFFS2,
MAC Filter
wl0, wl1
Vpn (OpenVPN Client)
Router/Version: Netgear R7000
Firmware: v3.0-r37630M kongac (11/12/18 )
Kernel: Linux 4.4.163-rc1 #607 SMP Mon Nov 12 23:10:30 CET 2018 armv7l
Previous: v3.0-r36840M kongac (09/03/18 )
Mode/Status: Up and runnig for 1 day
Reset: Soft boot before and after ddup
Issues/Errors: None
Upgraded via "ddup --flash-latest". No 'erase nvram' this time.
It looks like a new version is available already.
The temperatures are good: CPU 55.8 °C / WL0 44.5 °C / WL1 47.5 °C (The R7000 is wall-mounted.)
Current basic R7000 setup (subject to change of course):
- SFE - On
- STP - On
- Static WAN IP
- LAN DHCP Enabled
- IPv4 only
- Encrypt DNS disabled
- Wireless: Regulatory Domain = UNITED_STATES, wl0 Mixed (ch. 1), wl1 NA-Mixed (ch. 161 + 159), AES
- 1 wireless VLAN on wl0
- SNMP disabled, SSH enabled, Telnet disabled
- Firewall enabled, Log Level high
- Syslog: to local server. klogd: disabled.
- USB support - Off
- NO: ttraf, VNC, Zabbix, VPN, Radius, OpenVPN
- NO: UPnP, DMZ, QoS
- NO: Samba, CIFS, JFFS2, miniDLNA, Entware, Optware _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
Have used this extensively from my earlier comment till now. Zero issues faced.
Now trying to understand what's new in the later build, and then switching over to that.
This build is very stable for the R6400v2-OTP. Haven't tried VAP etc, which seems to be covered in the next build _________________ PROFESSIONAL STUDENT my.Mistakes ∝ my.Learning ... provided I have the patience & persistence to learn