Conceptronic C300BRS4A_V2 (RT3052F) RUNNING DD-WRT!!!!!!!!!

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware
Goto page Previous  1, 2
Author Message
papi4_atori
DD-WRT Novice


Joined: 28 Feb 2011
Posts: 3

PostPosted: Wed Mar 09, 2011 20:18    Post subject: Reply with quote
What do you mean when you say: Using a terminal program select 57600.8, N, 1
Sponsor
RogFanther
DD-WRT User


Joined: 24 May 2008
Posts: 156

PostPosted: Wed Mar 30, 2011 13:48    Post subject: Reply with quote
To use for example Hyperterminal in Windows, or Teraterm, and set the serial communications parameters to 57600, 8N1
papi4_atori
DD-WRT Novice


Joined: 28 Feb 2011
Posts: 3

PostPosted: Wed Apr 06, 2011 20:03    Post subject: Reply with quote
When you leave the next option to give a yes or no or ctrl c?

2: System Load Linux Kernel Then write to Flash via TFTP.
Warning! Linux in Flash Erase Then burn new one. Are you sure? (Y / N)
Please input new ones / or Ctrl-C to discard
PedRy
DD-WRT Novice


Joined: 02 Mar 2012
Posts: 7

PostPosted: Sun Mar 04, 2012 17:44    Post subject: Reply with quote
Hi.

I'm trying to install dd-wrt .

I'm using a CA-42 virtual serial cable from my old nokia.

The cable is attached to Com3 port.
All is conected and when I open terminal and connect with terminal screen is blank ... I can't do anything.

What I'm doing wrong?



Uploaded with ImageShack.us
lopesdasilva
DD-WRT Novice


Joined: 24 Apr 2012
Posts: 1

PostPosted: Tue Apr 24, 2012 14:16    Post subject: Reply with quote
Hi,
Is it possible that would could point a tutorial or make one?
With necessary material and steps? Thanks
PedRy
DD-WRT Novice


Joined: 02 Mar 2012
Posts: 7

PostPosted: Thu May 10, 2012 10:44    Post subject: Reply with quote
Hi, Here I am again.

When U-Boot starts automatically choose option 3 "Boot system code via Flash (default)."


Quote:
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.

You choosed 3

I have connected RX TX and GND cable.
What I'm doing wrong ?

Here's my log

Quote:
Code:
[size=9]=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2012.05.10 14:22:09 =~=~=~=~=~=~=~=~=~=~=~=



U-Boot 1.1.3 (Dec  8 2009 - 13:38:58)


Board: Ralink APSoC DRAM:  32 MB

relocate_code Pointer at: 81fb0000

flash_protect ON: from 0xBF000000 to 0xBF01D663

flash_protect ON: from 0xBF030000 to 0xBF030FFF

*** Warning - bad CRC, using default environment


============================================

Ralink UBoot Version: 3.3

--------------------------------------------

ASIC 3052_MP2 (Port5<->None)

DRAM component: 256 Mbits SDR

DRAM bus: 16 bit

Total memory: 32 MBytes

Flash component: NOR Flash

Date:Dec  8 2009  Time:13:38:58

============================================

icache: sets:256, ways:4, linesz:32 ,total:32768

dcache: sets:128, ways:4, linesz:32 ,total:16384


 ##### The CPU freq = 320 MHZ ####


SDRAM bus set to 16 bit

 SDRAM size =32 Mbytes


Please choose the operation:

   1: Load system code to SDRAM via TFTP.

   2: Load system code then write to Flash via TFTP.

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   9: Load Boot Loader code then write to Flash via TFTP.



You choosed 3


 0

   

3: System Boot system code via Flash.

## Booting image at bf050000 ...

   Image Name:   linkn Kernel Image

   Created:      2010-04-09  14:07:31 UTC

   Image Type:   MIPS Linux Kernel Image (lzma compressed)

   Data Size:    2204781 Bytes =  2.1 MB

   Load Address: 80000000

   Entry Point:  80366000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

No initrd

## Transferring control to Linux (at address 80366000) ...

## Giving linux memsize in MB, 32


Starting kernel ...



LINUX started...

 THIS IS ASIC
Linux version 2.6.21 (root@linux-6091) (gcc version 3.4.2) #1419 Fri Apr 9 22:07:21 CST 2010

 The CPU feqenuce set to 320 MHz
CPU revision is: 0001964c
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Built 1 zonelists.  Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 9080001c, status = 1100ff00
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 00138800(1280000)
CPU frequency 320.00 MHz
Using 160.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 27688k/32768k available (3031k kernel code, 5080k reserved, 444k data, 1180k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
detected lzma initramfs
detected lzma initramfs
initramfs: LZMA lc=3,lp=0,pb=2,dictSize=1048576,origSize=4327424
LZMA initramfs by Ming-Ching Tiew <mctiew@yahoo.com>...................................................................Load RT2880 Timer Module(Wdg/Soft)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
io scheduler noop registered (default)
FLASH_API: MAN_ID=C2 DEV_ID=22A8 SIZE=4MB
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
rdm_major = 254
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
AP Driver version-2.3.0.0
ralink flash device: 0x1000000 at 0x1f000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 4 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x00050000 : "Factory"
0x00050000-0x01000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "Ralink SoC physically mapped flash" -- size truncated to 0x3b0000
block2mtd: version $Revision: 1.1.1.1 $
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
arp_tables: (C) 2002 David S. Miller
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
net/ipv4/netfilter/ipt_netcheck.c 191 ipt_netcheck init
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.00  256 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
GDMA1_MAC_ADRH -- : 0x0000000c
GDMA1_MAC_ADRL -- : 0x43305277
PROC INIT OK!
Freeing unused kernel memory: 1180k freed

init started: BusyBox v1.12.1 (2010-04-09 20:09Algorithmics/MIPS FPU Emulator v1.5
:14 CST)

starting pid 13, tty '': '/etc_ro/rcS'
devpts: called with bogus options
Welcome to
     _______  _______  ___     __  ____   _  _   ___
    |  ___  \|   __  ||   |   |__||    \ | || | /  /
    | |___| ||  |__| ||   |__  __ |     \| || |/  /
    |   _   /kernel reg pid 21 success .
|   _   ||      ||  || |\     ||     \
    |__| \__\|__| |__||______||__||_| \____||_|\___\

                   =System Architecture Department=


starting pid 19, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2010-04-09 20:09:14 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

#

Yes:

      ****** WeLoveLinux ******

 Welcome to ...
httpd Reg gpio hook success .
RX DESC a1cf9000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff ff 00 00 01
Main bssid = 00:22:f7:25:82:98
<==== rt28xx_init, Status=0
0x1300 = 00064380
getIfLive: device eth2.1 not found.
maclist:
WLan[00:22:F7:25:82:98]
Lan[00:22:F7:25:82:98]
GDMA1_MAC_ADRH -- : 0x00000022
Wan[00:22:F7:25:GDMA1_MAC_ADRL -- : 0xf7258298
82:9d]

phy_tx_ring = 0x01d3b000, tx_ring = 0xa1d3b000

phy_rx_ring = 0x00000000, rx_ring = 0x00000000
RT305x_ESW: Link Status Changed
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 710000
eth2.1: Setting MAC address to  00 22 f7 25 82 98.
VLAN (eth2.1):  Underlying device (eth2) has same MAC, not checking promiscious mode.
eth2.2: Setting MAC address to  00 22 f7 25 82 9d.
device eth2 entered promiscuous mode
VLAN (eth2.2):  Setting underlying device (eth2) to promiscious mode.
getIfLive: device br0 not found.
eth2.1: dev_set_promiscuity(master, 1)
device eth2.1 entered promiscuous mode
Router ip address config success.
br0: port 1(eth2.1) entering learning state
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
libupnp: using UDP SSDP_PORT = 1900
br0: topology change detected, propagating
br0: port 1(eth2.1) entering forwarding state
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
killall: udhcpd: no process killed

***** g_wl_interface = ra0 ******

sh: rjclient: not found
httpd listen ip = 192.168.0.1 port = 80
TendaLog -> ok rtn.
MfgThread start loop.
macBcast uses obsolete (PF_INET,SOCK_PACKET)
udhcpc (v1.12.1) started
[/size]
PedRy
DD-WRT Novice


Joined: 02 Mar 2012
Posts: 7

PostPosted: Mon May 14, 2012 18:58    Post subject: Reply with quote
Nobody ? Sad
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7068

PostPosted: Tue May 15, 2012 3:18    Post subject: Reply with quote
PedRy wrote:

When U-Boot starts automatically choose option 3 "Boot system code via Flash (default)."



You have to make your choice before U-Boot enters the default choice.

_________________
I'm on a whiskey diet, lost 3 days already
PedRy
DD-WRT Novice


Joined: 02 Mar 2012
Posts: 7

PostPosted: Tue May 15, 2012 11:18    Post subject: Reply with quote
I can't make selection. Automatically choose option 3 and continues.



I Tried selecting 2 several times before U-boot


Should I connect more than 3 cables?
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7068

PostPosted: Wed May 16, 2012 2:16    Post subject: Reply with quote
PedRy wrote:

Should I connect more than 3 cables?


If there are more than 3 wires in the cable then it may be that one of them is for +3.3V to the serial side of the adapter.

Test if TX is working by twisting the Rx and TX wires together. Anything you type on the keyboard should be echoed back through the loopback you created and should show up on the screen.

_________________
I'm on a whiskey diet, lost 3 days already
PedRy
DD-WRT Novice


Joined: 02 Mar 2012
Posts: 7

PostPosted: Fri Nov 15, 2013 15:17    Post subject: Back to stock firmware Reply with quote
If I upload original firmware from TFTP

Code:

3: System Boot system code via Flash.
## Booting image at bf050000 ...
Bad Magic Number,7772676E



How can I do ?
lucasat
DD-WRT Novice


Joined: 12 Jan 2014
Posts: 1

PostPosted: Sun Jan 12, 2014 15:22    Post subject: Re: IT's A GO!!!!!!! Reply with quote
I've a C300BRS4A with only 2 antennas too but haven't two Winbond W9812G6IH-75 but only one ElectronTech EM63A16STS-6G.

what firmware you recommend?

Thank so much.

LucaSat
Goto page Previous  1, 2 Display posts from previous:    Page 2 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum