When you leave the next option to give a yes or no or ctrl c?
2: System Load Linux Kernel Then write to Flash via TFTP.
Warning! Linux in Flash Erase Then burn new one. Are you sure? (Y / N)
Please input new ones / or Ctrl-C to discard
When U-Boot starts automatically choose option 3 "Boot system code via Flash (default)."
Quote:
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 3
I have connected RX TX and GND cable.
What I'm doing wrong ?
BusyBox v1.12.1 (2010-04-09 20:09:14 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
#
Yes:
****** WeLoveLinux ******
Welcome to ...
httpd Reg gpio hook success .
RX DESC a1cf9000 size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff ff 00 00 01
Main bssid = 00:22:f7:25:82:98
<==== rt28xx_init, Status=0
0x1300 = 00064380
getIfLive: device eth2.1 not found.
maclist:
WLan[00:22:F7:25:82:98]
Lan[00:22:F7:25:82:98]
GDMA1_MAC_ADRH -- : 0x00000022
Wan[00:22:F7:25:GDMA1_MAC_ADRL -- : 0xf7258298
82:9d]
phy_tx_ring = 0x01d3b000, tx_ring = 0xa1d3b000
phy_rx_ring = 0x00000000, rx_ring = 0x00000000
RT305x_ESW: Link Status Changed
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 710000
eth2.1: Setting MAC address to 00 22 f7 25 82 98.
VLAN (eth2.1): Underlying device (eth2) has same MAC, not checking promiscious mode.
eth2.2: Setting MAC address to 00 22 f7 25 82 9d.
device eth2 entered promiscuous mode
VLAN (eth2.2): Setting underlying device (eth2) to promiscious mode.
getIfLive: device br0 not found.
eth2.1: dev_set_promiscuity(master, 1)
device eth2.1 entered promiscuous mode
Router ip address config success.
br0: port 1(eth2.1) entering learning state
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
libupnp: using UDP SSDP_PORT = 1900
br0: topology change detected, propagating
br0: port 1(eth2.1) entering forwarding state
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
killall: udhcpd: no process killed
***** g_wl_interface = ra0 ******
sh: rjclient: not found
httpd listen ip = 192.168.0.1 port = 80
TendaLog -> ok rtn.
MfgThread start loop.
macBcast uses obsolete (PF_INET,SOCK_PACKET)
udhcpc (v1.12.1) started
[/size]
If there are more than 3 wires in the cable then it may be that one of them is for +3.3V to the serial side of the adapter.
Test if TX is working by twisting the Rx and TX wires together. Anything you type on the keyboard should be echoed back through the loopback you created and should show up on the screen. _________________ Kernel panic: Aiee, killing interrupt handler!
Posted: Thu Aug 28, 2014 5:52 Post subject: Help Conceptronic C300BSR4A
I'm a dummy in this matter spite of having already researched a lot and read some articles. Would you like to help me and if possible one tuturial step by step to put my router:
-Conceptronic C300BSR4A,
-Firmware Version: C300BRS4A_v2_v1.0.0
-boot Version 2.1.0
-Hardware Version 2.0.
I've done the download ar670w-ddwrt-webflash.bin file for flashing, but whenever I do the firmware upgrade, it runs it normally as if everything had gone well (100%) and then does the reboot, but the firmware is always the same. I've read that this model has to do with a serial cable to the router and solder pins.
Would be possible to prepare a tuturial or video on youtube for this exact model, as doing so and then as flashing the router to DD-WRT.
Thank you|
I await the answers or toturiais ! :
thanls