Unrecognized Ethernet-Card Listings (PCI/PCIe/Onboard)

Post new topic   Reply to topic    DD-WRT Forum Index -> X86 based Hardware
Goto page Previous  1, 2, 3, 4, 5 ... 9, 10, 11  Next
Author Message
slimey
DD-WRT User


Joined: 14 Feb 2007
Posts: 334
Location: Texas

PostPosted: Sat Dec 15, 2007 17:34    Post subject: Reply with quote
02:03.0 Network Controller: Broadcom Corporation BCM4309 802.11/a/b/g (rev 03)
03:00.0 Ethernet Controller: Atheros Communications, Inc. AR5005G 802.11abg NIC (rev 01)
Sponsor
scoppy
DD-WRT User


Joined: 14 Oct 2006
Posts: 94

PostPosted: Sat Jan 12, 2008 14:25    Post subject: Reply with quote
DLINK DWL-G520M (atheros ar5005vl subchip ar5513 + ar5112) not supported

Code:
# lspci | grep Atheros
02:04.0 Ethernet controller: Atheros Communications, Inc. AR5005VL 802.11bg Wireless NIC (rev 01)

# lspci -v -s 02:04.0
02:04.0 Ethernet controller: Atheros Communications, Inc. AR5005VL 802.11bg Wireless NIC (rev 01)
        Subsystem: D-Link System Inc Unknown device 3a68
        Flags: bus master, medium devsel, latency 32, IRQ 10
        Memory at feac0000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: [44] Power Management version 2


# lspci -vvn -s 02:04.0
02:04.0 0200: 168c:0020 (rev 01)
        Subsystem: 1186:3a68
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at feac0000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-
hopester
DD-WRT Novice


Joined: 05 Feb 2008
Posts: 6

PostPosted: Tue Feb 05, 2008 16:12    Post subject: RTL8110SC Reply with quote
00:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet (rev 10)
Subsystem: Jetway Information Co., Ltd.: Unknown device 10ec
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 11
I/O ports at f600 [size=256]
Memory at fdfff000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 20000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2

00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet (rev 10)
Subsystem: Jetway Information Co., Ltd.: Unknown device 10ec
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 10
I/O ports at f800 [size=256]
Memory at fdffe000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 20020000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2

Not supported under V24 RC6.2
Rhamadahn Dave
DD-WRT Novice


Joined: 10 Feb 2008
Posts: 10

PostPosted: Mon Feb 11, 2008 18:21    Post subject: Reply with quote
00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)

onboard card off a asus a7n8x-e deluxe
lexridge
DD-WRT Guru


Joined: 07 Jun 2006
Posts: 928
Location: WV, USA

PostPosted: Wed Mar 05, 2008 20:22    Post subject: Reply with quote
Here is another one for you. This is a pair of ethernet controllers on a ITX Geode based MB (MSI Fuzzy LX800). The eth0 or eth1 presently do not show up on an ifconfig.

00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169S Gigabit Ethernet (Rev 10)

00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169S Gigabit Ethernet (Rev 10)

Lexridge
davel
DD-WRT User


Joined: 04 Mar 2008
Posts: 160
Location: Charlotte, NC

PostPosted: Thu Mar 06, 2008 3:00    Post subject: working on an sg-10 Reply with quote
working on an sg-10 that i pulled the modem out of the slot and put in a wireless card.. reg version of dd-wrt but not seeing the broadcom card.. Also tried older orinoco silver and a netgear wg511v2 in the card slot.. neither of those were seen at all..



00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at cc00 [size=256]
Memory at d5023000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2

00:09.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 0d)
Subsystem: Intel Corporation EtherExpress PRO/100 S Server Adapter
Flags: bus master, medium devsel, latency 32, IRQ 11
Memory at d5022000 (32-bit, non-prefetchable) [size=4K]
I/O ports at d000 [size=64]
Memory at d5000000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at 18000000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2

00:0a.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 02)
Subsystem: Dell TrueMobile 1300 WLAN Mini-PCI Card
Flags: bus master, fast devsel, latency 32, IRQ 12
Memory at d5020000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2

00:0b.0 CardBus bridge: O2 Micro, Inc. OZ601/6912/711E0 CardBus/SmartCardBus Controller
Subsystem: Unknown device 3412:7856
Flags: bus master, stepping, slow devsel, latency 168, IRQ 5
Memory at d5024000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10000000-13fff000 (prefetchable)
Memory window 1: 14000000-17fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
16-bit legacy interface ports at 0001
napkin
DD-WRT Novice


Joined: 12 Mar 2008
Posts: 1

PostPosted: Wed Mar 12, 2008 0:26    Post subject: Reply with quote
Idk how to get those printouts cause im a n00b

But if you could add support for D-Link DFE-530TX+ that would be awesome

Thanks Smile
olmari
DD-WRT Guru


Joined: 24 Oct 2006
Posts: 1447
Location: Finland

PostPosted: Fri Apr 25, 2008 20:22    Post subject: Reply with quote
Code:
05:00.0 Ethernet controller: Intel Corporation 82572EI Gigabit Ethernet Controller (Copper) (rev 06)
  Subsystem: Intel Corporation PRO/1000 PT Desktop Adapter


This is PCI-Express card, but that shouldn't make any diffirence? (as it is shown on the lspci list normally).

EDIT: If I also put an Intel 82541PI (normal PCI) NIC inside, then the new 82572EI starts to work!! lsmod shows e1000 module loaded this way... But when I remove again the normal PCI Intel and start up, no e1000 shows up in lsmod...

And obviously new PCI-Express card works too with e1000, so this one should be easy one to squash?
Extide
DD-WRT Novice


Joined: 28 Mar 2007
Posts: 8

PostPosted: Mon May 26, 2008 7:07    Post subject: how about this one Reply with quote
00:0d.0 Ethernet controller: Intel Corporation 82543GC Gigabit Ethernet Controller (Fiber) (rev 02)
It would be pretty cool if you could add this one for me, thx :)

Nevermind just needed to load the e1000 module -- maybe you should add this card's info to the autodetect scripts so it loads the e1000 module automagically.
BrainSlayer
Site Admin


Joined: 06 Jun 2006
Posts: 7463
Location: Dresden, Germany

PostPosted: Mon May 26, 2008 9:22    Post subject: Re: how about this one Reply with quote
Extide wrote:
00:0d.0 Ethernet controller: Intel Corporation 82543GC Gigabit Ethernet Controller (Fiber) (rev 02)
It would be pretty cool if you could add this one for me, thx :)

Nevermind just needed to load the e1000 module -- maybe you should add this card's info to the autodetect scripts so it loads the e1000 module automagically.


added it now too like the card before

_________________
"So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
niick
DD-WRT Novice


Joined: 22 Jun 2008
Posts: 1

PostPosted: Sun Jun 22, 2008 4:19    Post subject: Reply with quote
Hello,

I have two 3com cards they show up in lspci as;

01.01.0 Ethernet controller: 3Com Corporation 3CR990SVR95 [Typhoon Server 56-bit] (rev 02)
01.02.0 Ethernet controller: 3Com Corporation 3CR990SVR95 [Typhoon Server 56-bit] (rev 02)

Neither are detected at boot. If I run "insmod typhoon" then both start running.

Thanks, Nick
bgoksel
DD-WRT User


Joined: 19 Feb 2008
Posts: 80

PostPosted: Fri Jun 27, 2008 19:29    Post subject: Reply with quote
Hi all,

I have mpci as Ar5211A that supports A and B,NO G.
On V24 System Summery table it show power output only `0` and cant make 100 meter links with it.

it starts radio and signal is awfull...

What could be the reason for it?

Thanks..
xaim00
DD-WRT Novice


Joined: 23 Jun 2008
Posts: 40

PostPosted: Wed Jul 16, 2008 5:23    Post subject: Reply with quote
Wireless card Zyxel m-302 is not supported in v24 (stable). It uses the AR5513 (AR5005VL) chipset i believe.

lspci output:

00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management (rev a1)
00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 Controller (reva2)
00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2)
00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller (v2.5) (rev a2)
00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2)
00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] AddressMap
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
02:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
02:08.0 Ethernet controller: Atheros Communications Inc. AR5513 802.11abg Wireless NIC (rev 01)
02:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
02:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
02:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
scoppy
DD-WRT User


Joined: 14 Oct 2006
Posts: 94

PostPosted: Mon Aug 04, 2008 20:41    Post subject: Reply with quote
for ar5513 i have found MIPS driver from dlink di-624m router

this link ftp://ftp.dlink.com/GPL/DI-624M/DI-624M-Src.tgz is the open source SDK for D-Link DI-624m MIMO router (contains atheros driver)

this the dir atheros

ar5513_drv.o ar5513_main.o ar.o atdi.o

and this is the README
Code:

#Atheros Thin PCI driver README file.

1. Compiling the driver:

    Change Makefile "KERNELDIR" variable to point to your linux kernel.

2. Loading the driver.

   #insmod ./ar.o mode=tx

   NOTE: Run "ifconfig eth1 <ip addr> up" after loading the driver
         successfully.

3. Unloading the driver.

   #rmmod ar

can some one reverse engineering this MIPS driver?





scoppy wrote:
DLINK DWL-G520M (atheros ar5005vl subchip ar5513 + ar5112) not supported

Code:
# lspci | grep Atheros
02:04.0 Ethernet controller: Atheros Communications, Inc. AR5005VL 802.11bg Wireless NIC (rev 01)

# lspci -v -s 02:04.0
02:04.0 Ethernet controller: Atheros Communications, Inc. AR5005VL 802.11bg Wireless NIC (rev 01)
        Subsystem: D-Link System Inc Unknown device 3a68
        Flags: bus master, medium devsel, latency 32, IRQ 10
        Memory at feac0000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: [44] Power Management version 2


# lspci -vvn -s 02:04.0
02:04.0 0200: 168c:0020 (rev 01)
        Subsystem: 1186:3a68
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 32 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at feac0000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-
kit
DD-WRT Novice


Joined: 24 Dec 2008
Posts: 6

PostPosted: Fri Dec 26, 2008 9:32    Post subject: Reply with quote
Are the Linksys Gigabit EG1032 supported?

Here's the lspci result, also included is the built-in NIC:

02:00.0 Ethernet controller: Attansic Technology Corp. L2 100 Mbit Ethernet Adapter
Subsystem: Biostar Microtech Int'l Corp: Unknown device 2800
Flags: bus master, fast devsel, latency 0, IRQ 10
Memory at fdd80000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at fdc00000 [disabled][size=128K]
Capabilities: [40] Power Mangement version 2
Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable
Capabilities: [58] #10 [0001]

03:01.0 Ethernet controller: Linksys Gigabit Network Adapter (rev 10)
Subsystem: Linksys EG1032 v3 Instant Gigabit Network Adapter
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 10
I/O ports at de00 [size=256]
Memory at fdaff000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at fd900000 [disabled] [size=128K]
Capabilities: [dc] Power Managenement version 2

03:02.0 Ethernet controller: Linksys Gigabit Network Adapter (rev 10)
Subsystem: Linksys EG1032 v3 Instant Gigabit Network Adapter
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 5
I/O ports at dc00 [size=256]
Memory at fdafe000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at fd920000 [disabled] [size=128K]
Capabilities: [dc] Power Managenement version 2

Here's more info on the chipset used by thi sNIC:

LINKSYS EG1032 V.3
RTL8169S-32
82506S1

Thanks
Goto page Previous  1, 2, 3, 4, 5 ... 9, 10, 11  Next Display posts from previous:    Page 4 of 11
Post new topic   Reply to topic    DD-WRT Forum Index -> X86 based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum