Posted: Wed Nov 22, 2023 6:25 Post subject: New Build - 11/21/2023 - r54095
Welcome to x86 / x64 r54095 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 16 Jun 2006 Posts: 151 Location: Germany, BW
Posted: Wed Nov 22, 2023 9:43 Post subject:
Router/Version: HP ProDesk 600 G2 Mini File/Kernel: X64-dd54095-webupgrade_public_vga.bin / Linux 6.1.63 #438 SMP Wed Nov 22 11:34:00 +06 2023 Previous/Reset: 53045, no reset Mode/Status: Issues/Errors: USB3-LAN-Adapter not working anymore
Have you tried erasing your nvram back to defaults so its boots to a fresh configuration? Sometimes the restore to factory defaults in Webgui does not work. You have to manually login to the terminal with the command of "erase nvram" then use reboot command to restart the system.
It will rerun a detection on a fresh configuration that is only done the first boot with fresh nvram config. But you may have to enable USB core first.
Or try these commands at the terminal prompt after enabling USB core.
rmmod ax88179_178a
then
modprobe usbnet
If this makes it work again. Go to the administration section then click on commands.
Click Edit for Startup
Copy and paste those commands so it looks like this.
rmmod ax88179_178a
modprobe usbnet
Then click save startup. Then go ahead and try a reboot. During startup it will run those commands to make it work at every startup.
Joined: 16 Nov 2015 Posts: 6439 Location: UK, London, just across the river..
Posted: Thu Nov 23, 2023 11:13 Post subject:
flood404 wrote:
Have you tried erasing your nvram back to defaults so its boots to a fresh configuration? Sometimes the restore to factory defaults in Webgui does not work. You have to manually login to the terminal with the command of "erase nvram" then use reboot command to restart the system.
in general for routers nvram reset is done by nvram erase command...instead of "erase nvram"..
but, dont know how it goes to x86 / x64 PC routers systems... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Have you tried erasing your nvram back to defaults so its boots to a fresh configuration? Sometimes the restore to factory defaults in Webgui does not work. You have to manually login to the terminal with the command of "erase nvram" then use reboot command to restart the system.
in general for routers nvram reset is done by nvram erase command...instead of "erase nvram"..
but, dont know how it goes to x86 / x64 PC routers systems...
It could be flipped as you said. I am just trying to go by what I remember. I don't use that command often to get it right the first time.
Posted: Thu Nov 23, 2023 11:40 Post subject: Gigabyte Technology Co., Ltd. B85M-D3H
Running the free VGA build with the Gigabyte Technology Co., Ltd. B85M-D3H board, 4770K 4 core 8 thread gen 4 cpu. Speedstep enabled. 16GB ram, Several HDD as a NAS and a Realtek 6 port 2.5Gbps for LAN and Onboard Realtek for WAN.
This build seems to be more stable than previous version. So far it's been up for 22 hours.
Joined: 16 Jun 2006 Posts: 151 Location: Germany, BW
Posted: Thu Nov 23, 2023 14:55 Post subject:
i even didn't think about that part....
rmmod showed that driver is not loaded, so I did
1. insmod ax88179_178a
ip addr show now shows me eth1, but its down, so I did
2. ifconfig eth1 up
Putting these 2 command on top of my startup is working, but obviously eth1 comes up too late to get part of br0.
I know, that also can be fixed by hand, but it's just a pain and maybe there is other stuff not running properly because of the late up-status of eth1.