I'm a bit unclear on if any builds besides the one attached to this thread will work for my E1000 v1, after the initial flashing. Will all K26 builds work, or only ECO K26 builds newer than the one posted, or only the one posted?
I would prefer to have a standard build rather than a mini build on my router if possible.
Joined: 26 Jan 2008 Posts: 13049 Location: Behind The Reset Button
Posted: Wed Oct 20, 2010 13:03 Post subject:
jsmith45 wrote:
I'm a bit unclear on if any builds besides the one attached to this thread will work for my E1000 v1, after the initial flashing. Will all K26 builds work, or only ECO K26 builds newer than the one posted, or only the one posted?
I would prefer to have a standard build rather than a mini build on my router if possible.
Thanks for any help.
TMK... as long as the build number is above the 1st posted build, it should be OK. Take note of the files size though. Some of the std builds are too large for a 4mb router. _________________ [Moderator Deleted]
yay, it worked; however there is no openvpn on this firmware, and i want to know if this --> dd-wrt.v24-14929_NEWD-2_K2.6_openvpn_small.bin
3256 KB
8/12/2010
11:35:00 AM
Posted: Wed Oct 27, 2010 18:27 Post subject: wireless n
hi, i followed the wireless-n guide and set up everything i could find. i stuck with the 20 mhz 2.4 range because i didn't want o mess up my neighbors; my status wireless page says it's using the 54mbps though.
Wireless Status
MAC Address
55:6D:43:C0:D3:7I
Radio
Radio is On
Mode
AP
Network
Mixed
SSID
Home-WiFi
Channel
9
TX Power
71 mW
Rate
54 Mbps
Encryption - Interface wl0
Enabled, WPA2 Personal
PPTP Status
Disconnected
Joined: 13 Nov 2009 Posts: 247 Location: Morehead,Kentucky
Posted: Wed Oct 27, 2010 18:59 Post subject: Re: wireless n
ddwrt000019 wrote:
hi, i followed the wireless-n guide and set up everything i could find. i stuck with the 20 mhz 2.4 range because i didn't want o mess up my neighbors; my status wireless page says it's using the 54mbps though.
Wireless Status
MAC Address
55:6D:43:C0:D3:7I
Radio
Radio is On
Mode
AP
Network
Mixed
SSID
Home-WiFi
Channel
9
TX Power
71 mW
Rate
54 Mbps
Encryption - Interface wl0
Enabled, WPA2 Personal
PPTP Status
Disconnected
Because You are using 20mhz, and not the 40mhz bonding. So it will limit it to 54Mb. _________________ Linksys E3000
DD-WRT v24-sp2 (12/19/10) big
(SVN revision 15943M NEWD-2 K2.6 Eko)
Just want to make sure which build I can flash my E1000 version 1? I can not find any NEW-2 K26 OPENVPN build named e1000...
Will "dd-wrt.v24-15962_NEWD-2_K2.6_openvpn_small.bin" work???
Thanks!
barryware wrote:
Zelda wrote:
Can anyone answer my question about putting std_nokaid-small on here? I have downloaded and tried to flash dd-wrt.v24-13527_NEWD2_K2.6_std_nokaid_small.bin and it fails and now I get lights and everything on the router but its unaccessible. I may have to tftp the original ddwrt.v24-15334_NEWD2_K2.6_mini_e1000.bin back on there.
So in a way I may have answered my own question.
15279 was the 1st build for the e1000. any builds earlier than that (13527) will not have the code for the e1000.
Joined: 26 Jan 2008 Posts: 13049 Location: Behind The Reset Button
Posted: Wed Jan 05, 2011 15:24 Post subject:
lijianch wrote:
I have bricked many routers. You know it. LOL
Just want to make sure which build I can flash my E1000 version 1? I can not find any NEW-2 K26 OPENVPN build named e1000...
Will "dd-wrt.v24-15962_NEWD-2_K2.6_openvpn_small.bin" work???
Thanks!
barryware wrote:
Zelda wrote:
Can anyone answer my question about putting std_nokaid-small on here? I have downloaded and tried to flash dd-wrt.v24-13527_NEWD2_K2.6_std_nokaid_small.bin and it fails and now I get lights and everything on the router but its unaccessible. I may have to tftp the original ddwrt.v24-15334_NEWD2_K2.6_mini_e1000.bin back on there.
So in a way I may have answered my own question.
15279 was the 1st build for the e1000. any builds earlier than that (13527) will not have the code for the e1000.
Your E1000 V1.. Has 4mb flash and must us a k26 build and the build must be newer than 15279 as that was the 1st build that had support for the E1000.
Remember, the E1000 is not like the 2000 & 3000.. Nvram is the same so it does not require a trailed build after the initial flash from stock to dd-wrt.
Normal flashing procedures apply.. Biggest thing it to check "reset to defaults settings" after the flash in the upgrade gui and WAIT after flashing. The data transfer only takes a few seconds. The checking, writing of the flash, checking again, and booting takes some time. _________________ [Moderator Deleted]