Linksys E1000 now supported (V.1 ONLY!)

Post new topic   This topic is locked: you cannot edit posts or make replies.    DD-WRT Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3, 4, 5, 6
Author Message
3l3tric
DD-WRT Novice


Joined: 23 May 2012
Posts: 11

PostPosted: Sat Jul 26, 2014 4:12    Post subject: Reply with quote
FYI,
I flashed Build 21676 (STD-Nokaid) to my E1000 V1, and have had no issues thus far, save for the fact that Over/Under clocking doesn't work. The option wasn't even available before, so this comes as no surprise.
Link directly to the build I used
Sponsor
bacon612
DD-WRT User


Joined: 09 Mar 2007
Posts: 82

PostPosted: Sat Jul 26, 2014 23:41    Post subject: Reply with quote
3l3tric wrote:
FYI,
I flashed Build 21676 (STD-Nokaid) to my E1000 V1, and have had no issues thus far, save for the fact that Over/Under clocking doesn't work. The option wasn't even available before, so this comes as no surprise.
Link directly to the build I used


Thanks for the share. I work with a bunch of these little gems. Are you able to verify that you are able to achive full 300mbps wireless n on this firmware? Or at least successfull 40mhz speeds above 150mbps?
3l3tric
DD-WRT Novice


Joined: 23 May 2012
Posts: 11

PostPosted: Sun Jul 27, 2014 15:48    Post subject: Reply with quote
bacon612 wrote:
3l3tric wrote:
FYI,
I flashed Build 21676 (STD-Nokaid) to my E1000 V1, and have had no issues thus far, save for the fact that Over/Under clocking doesn't work. The option wasn't even available before, so this comes as no surprise.
Link directly to the build I used


Thanks for the share. I work with a bunch of these little gems. Are you able to verify that you are able to achive full 300mbps wireless n on this firmware? Or at least successfull 40mhz speeds above 150mbps?

I'll check the network speeds a bit later today, but I probably will not be able to check N-band speeds. I'll see though.
It's definitely an awesome router. So much better than the one I'm using as an access point (WRT54G2 V1).
jheide44
DD-WRT Guru


Joined: 03 Sep 2013
Posts: 739

PostPosted: Sun Apr 19, 2015 16:03    Post subject: Reply with quote
FWIW...

Just performed initial flash from stock using the trailed v1 26653 mini


quote below from here:
http://www.dd-wrt.com/phpBB2/viewtopic.php?p=963099#963099

jheide44 wrote:
E1000 (v1)
Stock 2.0.01 --> 26653 mini
** Reset (before and after) **

File: dd-wrt.v24-26653_NEWD-2_K2.6_mini_e1000v1.bin
MD5: 96de22dfe682b03c8fa141c6a82cb9ee

only been up for a few minutes now, but seems to be getting a nice wifi signal (wide HT40, WPA2 + AES)

not much else tested (i.e not being deployed in a very complex WiFi solution)


File from here:
ftp://ftp.dd-wrt.com/betas/2015/04-09-2015-r26653/broadcom_K26/

_________________
reenignE esreveR
Resistance is NOT futile... It's Voltage divided by Current!


_.-:Curently Deployed Devices:-._
Loc_1.0: R6400 -- v3.0-r51887 std (02/28/23)
Loc_2.0: R6300v2 -- Kong PTB 35550M 03-28-2018

Others: too many others to list

R7000 (& similar HW) Tips/Tricks HERE.

Assumptions:
1. Everyone on the forum has read the relevant forum section announcements.
2. For Broadcom section we have ALL at least tried to understand the "Peacock" thread,
HERE
Goto page Previous  1, 2, 3, 4, 5, 6 Display posts from previous:    Page 6 of 6
Post new topic   This topic is locked: you cannot edit posts or make replies.    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum