cammen3 DD-WRT Novice
Joined: 13 Feb 2012 Posts: 10
|
Posted: Thu Jun 14, 2012 13:49 Post subject: |
|
LOM wrote: | I can't tell you what is possible for you to do until I have more info on the modem.
I have given you a link to the wiki page which explains what info you have to provide. |
I hope that this is the information that you'll need. If it's not, I'm sorry
comgt -d /dev/usb/tts/0 info output
Code: | /bin/sh: can't open /dev/usb/tts/0: no such file
##### Wireless WAN Modem Configuration #####
Can't open device /dev/usb/tts/0. |
dmesg
Code: | <5>[ 0.000000] Linux version 3.3.8-svn19342 (root@dd-wrt) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #419 Fri Jun 8 08:12:10 CEST 2012
<4>[ 0.000000] flash_size passed from bootloader = 8
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
<6>[ 0.000000] booting platform Atheros AR9132 rev 2 (0xb9)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 02000000 @ 00000000 (usable)
<4>[ 0.000000] Zone PFN ranges:
<4>[ 0.000000] Normal 0x00000000 -> 0x00002000
<4>[ 0.000000] Movable zone start PFN for each node
<4>[ 0.000000] Early memory PFN ranges
<4>[ 0.000000] 0: 0x00000000 -> 0x00002000
<7>[ 0.000000] On node 0 totalpages: 8192
<7>[ 0.000000] free_area_init_node: node 0, pgdat 80276c70, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 64 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<4>[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<6>[ 0.000000] Memory: 29488k/32768k available (2123k kernel code, 3280k reserved, 393k data, 160k init, 0k highmem)
<6>[ 0.000000] NR_IRQS:80
<0>[ 0.000000] irq init done
<4>[ 0.000000] plat_time_init: plat time init done
<6>[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
<6>[ 0.080000] pid_max: default: 32768 minimum: 301
<6>[ 0.080000] Mount-cache hash table entries: 512
<6>[ 0.090000] NET: Registered protocol family 16
<6>[ 0.110000] bio: create slab at 0
<6>[ 0.120000] Switching to clocksource MIPS
<6>[ 0.120000] NET: Registered protocol family 2
<6>[ 0.130000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.130000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
<6>[ 0.140000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
<6>[ 0.140000] TCP: Hash tables configured (established 1024 bind 1024)
<6>[ 0.150000] TCP reno registered
<6>[ 0.150000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.160000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.160000] NET: Registered protocol family 1
<5>[ 0.170000] gpio_proc: module loaded and /proc/gpio/ created
<6>[ 0.180000] Register LED Device
<6>[ 0.180000] gpiochip_add: registered GPIOs 0 to 63 on device: ar71xx
<5>[ 0.190000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<4>[ 0.190000] AR7100 GPIOC major 0
<6>[ 0.200000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.200000] msgmni has been set to 57
<6>[ 0.210000] io scheduler noop registered
<6>[ 0.210000] io scheduler deadline registered (default)
<6>[ 0.220000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.240000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
<6>[ 0.250000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.260000] guessed flashsize = 8M
<0>[ 0.270000] scanning for root partition
<0>[ 0.270000] tplink uboot detected
<0>[ 0.270000] bootloader size = 20000
<0>[ 0.280000]
<0>[ 0.280000] found squashfs at 100000
<5>[ 0.290000] Creating 8 MTD partitions on "ar7100-nor0":
<5>[ 0.290000] 0x000000000000-0x000000020000 : "RedBoot"
<5>[ 0.300000] 0x000000020000-0x0000007e0000 : "linux"
<5>[ 0.300000] 0x000000100000-0x0000006f0000 : "rootfs"
<5>[ 0.310000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.320000] 0x0000006f0000-0x0000007e0000 : "ddwrt"
<5>[ 0.320000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.330000] 0x0000007f0000-0x000000800000 : "FIS directory"
<5>[ 0.340000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.340000] 0x000000000000-0x000000800000 : "fullflash"
<4>[ 0.350000] ->Oops: flash id 0x10216 .
<6>[ 0.350000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.360000] tun: (C) 1999-2004 Max Krasnyansky
<4>[ 0.370000] Found an RTL8366RB switch
<5>[ 0.370000] Realtek RTL8366RB ethernet switch driver version 0.2.3
<6>[ 0.380000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
<6>[ 0.380000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
<6>[ 0.440000] rtl8366rb: probed
<6>[ 0.640000] PPP generic driver version 2.4.2
<6>[ 0.650000] PPP BSD Compression module registered
<6>[ 0.650000] PPP Deflate Compression module registered
<6>[ 0.660000] PPP MPPE Compression module registered
<6>[ 0.660000] NET: Registered protocol family 24
<6>[ 0.670000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout= 0)
<7>[ 0.680000] Registered led device: generic_0
<7>[ 0.680000] Registered led device: generic_1
<7>[ 0.680000] Registered led device: generic_2
<7>[ 0.680000] Registered led device: generic_3
<7>[ 0.680000] Registered led device: generic_4
<7>[ 0.680000] Registered led device: generic_5
<7>[ 0.680000] Registered led device: generic_6
<7>[ 0.680000] Registered led device: generic_7
<7>[ 0.680000] Registered led device: generic_8
<7>[ 0.680000] Registered led device: generic_9
<7>[ 0.680000] Registered led device: generic_10
<7>[ 0.680000] Registered led device: generic_11
<7>[ 0.680000] Registered led device: generic_12
<7>[ 0.680000] Registered led device: generic_13
<7>[ 0.680000] Registered led device: generic_14
<7>[ 0.680000] Registered led device: generic_15
<7>[ 0.680000] Registered led device: generic_16
<7>[ 0.690000] Registered led device: generic_17
<7>[ 0.690000] Registered led device: generic_21
<7>[ 0.690000] Registered led device: generic_22
<7>[ 0.690000] Registered led device: generic_23
<7>[ 0.690000] Registered led device: generic_24
<7>[ 0.690000] Registered led device: generic_25
<7>[ 0.690000] Registered led device: generic_26
<7>[ 0.690000] Registered led device: generic_27
<7>[ 0.690000] Registered led device: generic_28
<7>[ 0.690000] Registered led device: generic_29
<7>[ 0.690000] Registered led device: generic_30
<7>[ 0.690000] Registered led device: generic_31
<6>[ 0.690000] u32 classifier
<6>[ 0.690000] input device check on
<6>[ 0.700000] Actions configured
<6>[ 0.700000] Netfilter messages via NETLINK v0.30.
<6>[ 0.700000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
<4>[ 0.710000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 0.710000] nf_nat_rtsp v0.6.21 loading
<6>[ 0.720000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 0.720000] IPP2P v0.8.2 loading
<6>[ 0.730000] TCP westwood registered
<6>[ 0.730000] TCP hybla registered
<6>[ 0.730000] TCP vegas registered
<6>[ 0.740000] NET: Registered protocol family 17
<5>[ 0.740000] Bridge firewalling registered
<6>[ 0.750000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 0.750000] searching for nvram
<6>[ 0.750000] nvram size = 0
<6>[ 0.790000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 0.800000] Freeing unused kernel memory: 160k freed
<6>[ 3.740000] eth0: Atheros AG71xx at 0xb9000000, irq 4
<7>[ 4.160000] ar71xx: pll_reg 0xb8050014: 0x1a000000
<6>[ 4.160000] eth0: link up (1000Mbps/Full duplex)
<6>[ 4.420000] Compat-wireless backport release: compat-wireless-2012-04-13-1-r31296
<6>[ 4.420000] Backport based on wireless-testing.git master-2012-04-13
<6>[ 4.600000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 5.120000] cfg80211: World regulatory domain updated:
<6>[ 5.130000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 5.140000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.150000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.150000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.160000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.170000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<7>[ 5.330000] ath: EEPROM regdomain: 0x0
<7>[ 5.330000] ath: EEPROM indicates default country code should be used
<7>[ 5.330000] ath: doing EEPROM country->regdmn map search
<7>[ 5.330000] ath: country maps to regdmn code: 0x3a
<7>[ 5.330000] ath: Country alpha2 being used: US
<7>[ 5.330000] ath: Regpair used: 0x3a
<7>[ 5.360000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 5.360000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
<6>[ 5.370000] cfg80211: Calling CRDA for country: US
<6>[ 5.470000] cfg80211: Regulatory domain changed to country: US
<6>[ 5.480000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 5.490000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 5.500000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 5.500000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.510000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.520000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.530000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<6>[ 5.850000] usbcore: registered new interface driver usbfs
<6>[ 5.860000] usbcore: registered new interface driver hub
<6>[ 5.870000] usbcore: registered new device driver usb
<6>[ 5.960000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 6.000000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 6.000000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<6>[ 6.040000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 6.060000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 6.060000] hub 1-0:1.0: USB hub found
<6>[ 6.070000] hub 1-0:1.0: 1 port detected
<6>[ 6.390000] usb 1-1: new high-speed USB device number 2 using ar71xx-ehci
<6>[ 8.160000] device vlan1 entered promiscuous mode
<6>[ 8.160000] device eth0 entered promiscuous mode
<6>[ 8.170000] br0: port 1(vlan1) entered forwarding state
<6>[ 8.170000] br0: port 1(vlan1) entered forwarding state
<6>[ 8.250000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 8.280000] cfg80211: World regulatory domain updated:
<6>[ 8.280000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 8.290000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.300000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.310000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.320000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.320000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.330000] cfg80211: Calling CRDA for country: SE
<6>[ 8.350000] cfg80211: Regulatory domain changed to country: SE
<6>[ 8.360000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 8.360000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
<6>[ 8.370000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
<6>[ 8.380000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
<6>[ 8.390000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
<6>[ 10.170000] br0: port 1(vlan1) entered forwarding state
<6>[ 16.010000] device ath0 entered promiscuous mode
<6>[ 16.310000] br0: port 2(ath0) entered forwarding state
<6>[ 16.320000] br0: port 2(ath0) entered forwarding state
<6>[ 18.320000] br0: port 2(ath0) entered forwarding state
<6>[ 18.380000] usbcore: registered new interface driver cdc_acm
<6>[ 18.380000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
<6>[ 18.520000] usbcore: registered new interface driver usbserial
<6>[ 18.520000] USB Serial support registered for generic
<6>[ 18.530000] usbcore: registered new interface driver usbserial_generic
<6>[ 18.540000] usbserial: USB Serial Driver core
<6>[ 18.710000] USB Serial support registered for Sierra USB modem
<6>[ 18.720000] usbcore: registered new interface driver sierra
<6>[ 18.730000] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
<6>[ 18.880000] USB Serial support registered for GSM modem (1-port)
<6>[ 18.890000] usbcore: registered new interface driver option
<6>[ 18.890000] option: v0.7.2:USB Driver for GSM modems
<6>[ 20.360000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
<6>[ 20.360000] Hooking IMQ before NAT on PREROUTING.
<6>[ 20.370000] Hooking IMQ after NAT on POSTROUTING. |
cat /sys/kernel/debug/usb/devices
Code: | T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.03
S: Manufacturer=Linux 3.3.8-svn19342 ehci_hcd
S: Product=Atheros AR91xx built-in EHCI controller
S: SerialNumber=platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0284 Rev= 0.00
S: Manufacturer=ZTE,Incorporated
S: Product=ZTE LTE Technologies MSM
S: SerialNumber=MF880FFFFS111111
C:* #Ifs= 6 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms |
lsusb -v
Code: | lsusb -v: /bin/sh: eval: line 1: lsusb: not found |
If this not was the information that you wanted, I'm once again sorry. And then, where am I supposed to enter those commands? |
|