bababooey DD-WRT Novice
Joined: 26 Feb 2011 Posts: 39
|
Posted: Thu Sep 19, 2013 18:45 Post subject: serial recovery question |
|
i had a linksys wrt320n brick on me randomly and using a serial usb tty connector, im having trouble typing in commands. im new to recovering bricks but it looks like cfe is screwed. i can see some output but when i break boot, and get a cfe prompt, its taking forever to type a letter, and if i do say type in ifconfig, and hit enter, it does nothing. my goal is to get it to set eth0 so i can tftp in a flash but is this thing screwed? i got my gnd, tx, rx, connections pretty good on it. note - i cant ping 192.168.1.1 or get any lan ports to work
heres my hyperterminal, output. minicom on linux provides similar results
Code: |
CFE mem: 0x80700000 - 0x807A1360 (660320)
Data: 0x80733440 - 0x80736700 (12992)
BSS: 0x80736700 - 0x8073B360 (19552)
Heap: 0x8073B360 - 0x8079F360 (409600)
Stack: 0x8079F360 - 0x807A1360 (8192)
Text: 0x80700000 - 0x80733438 (209976)
Boot version: v5.4
The boot is CFE
Nothing...
### CLKDIV= 0x80a082c, SFlashClkDiv=8 clkdivsf=2 ###
### Change it to 0x20a082c (2) ###
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0: hwaddr 00-25-9C-57-9E-6E, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x780000 (7864320) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x9D0 (2512) (0xBC0409D0)
Offset2: 0x15E000 (1433600) (0xBC19E000)
CFE version 5.10.56.51 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Apr 15 11:11:42 CST 2010 (fpan@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
No DPN
This is a Serial Flash
Boot partition size = 262144(0x40000)
Found a 8MB ST compatible serial flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F0FFF (8064996)
nvram #03 007F1000 -> 007FFFFF (61440)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F0FFF (8065024)
nvram #02 007F1000 -> 007FFFFF (61440)
BCM47XX_GMAC_ID
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.51
CPU type 0x19740: 354MHz
Tot mem: 32768 KBytes
CFE mem: 0x80700000 - 0x807A1360 (660320)
Data: 0x80733440 - 0x80736700 (12992)
BSS: 0x80736700 - 0x8073B360 (19552)
Heap: 0x8073B360 - 0x8079F360 (409600)
Stack: 0x8079F360 - 0x807A1360 (8192)
Text: 0x80700000 - 0x80733438 (209976)
Boot version: v5.4
The boot is CFE
Nothing...
### CLKDIV= 0x80a082c, SFlashClkDiv=8 clkdivsf=2 ###
### Change it to 0x20a082c (2) ###
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0: hwaddr 00-25-9C-57-9E-6E, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x780000 (7864320) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x9D0 (2512) (0xBC0409D0)
Offset2: 0x15E000 (1433600) (0xBC19E000)
àÀÿþ
CFE version 5.10.56.51 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Apr 15 11:11:42 CST 2010 (fpan@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
No DPN
This is a Serial Flash
Boot partition size = 262144(0x40000)
Found a 8MB ST compatible serial flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F0FFF (8064996)
nvram #03 007F1000 -> 007FFFFF (61440)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F0FFF (8065024)
nvram #02 007F1000 -> 007FFFFF (61440)
BCM47XX_GMAC_ID
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.51
CPU type 0x19740: 354MHz
Tot mem: 32768 KBytes
CFE mem: 0x80700000 - 0x807A1360 (660320)
Data: 0x80733440 - 0x80736700 (12992)
BSS: 0x80736700 - 0x8073B360 (19552)
Heap: 0x8073B360 - 0x8079F360 (409600)
Stack: 0x8079F360 - 0x807A1360 (8192)
Text: 0x80700000 - 0x80733438 (209976)
Boot version: v5.4
The boot is CFE
Nothing...
### CLKDIV= 0x80a082c, SFlashClkDiv=8 clkdivsf=2 ###
### Change it to 0x20a082c (2) ###
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0: hwaddr 00-25-9C-57-9E-6E, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x780000 (7864320) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x9D0 (2512) (0xBC0409D0)
Offset2: 0x15E000 (1433600) (0xBC19E000)
À
CFE version 5.10.56.51 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Apr 15 11:11:42 CST 2010 (fpan@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
No DPN
This is a Serial Flash
Boot partition size = 262144(0x40000)
Found a 8MB ST compatible serial flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F0FFF (8064996)
nvram #03 007F1000 -> 007FFFFF (61440)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F0FFF (8065024)
nvram #02 007F1000 -> 007FFFFF (61440)
BCM47XX_GMAC_ID
CFE version 5.10.56.51 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Apr 15 11:11:42 CST 2010 (fpan@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
No DPN
This is a Serial Flash
Boot partition size = 262144(0x40000)
Found a 8MB ST compatible serial flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F0FFF (8064996)
nvram #03 007F1000 -> 007FFFFF (61440)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F0FFF (8065024)
nvram #02 007F1000 -> 007FFFFF (61440)
BCM47XX_GMAC_ID
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.51
CPU type 0x19740: 354MHz
Tot mem: 32768 KBytes
CFE mem: 0x80700000 - 0x807A1360 (660320)
Data: 0x80733440 - 0x80736700 (12992)
BSS: 0x80736700 - 0x8073B360 (19552)
Heap: 0x8073B360 - 0x8079F360 (409600)
Stack: 0x8079F360 - 0x807A1360 (8192)
Text: 0x80700000 - 0x80733438 (209976)
CFE version 5.10.56.51 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Apr 15 11:11:42 CST 2010 (fpan@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
No DPN
This is a Serial Flash
Boot partition size = 262144(0x40000)
Found a 8MB ST compatible serial flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F0FFF (8064996)
nvram #03 007F1000 -> 007FFFFF (61440)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F0FFF (8065024)
nvram #02 007F1000 -> 007FFFFF (61440)
BCM47XX_GMAC_ID
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.51
CPU type 0x19740: 354MHz
Tot mem: 32768 KBytes
CFE mem: 0x80700000 - 0x807A1360 (660320)
Data: 0x80733440 - 0x80736700 (12992)
BSS: 0x80736700 - 0x8073B360 (19552)
Heap: 0x8073B360 - 0x8079F360 (409600)
Stack: 0x8079F360 - 0x807A1360 (8192)
Text: 0x80700000 - 0x80733438 (209976)
Boot version: v5.4
The boot is CFE
Nothing...
### CLKDIV= 0x80a082c, SFlashClkDiv=8 clkdivsf=2 ###
### Change it to 0x20a082c (2) ###
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Device eth0: hwaddr 00-25-9C-57-9E-6E, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Automatic startup canceled via Ctrl-C / ESC
|
|
|
bababooey DD-WRT Novice
Joined: 26 Feb 2011 Posts: 39
|
Posted: Sat Sep 21, 2013 11:35 Post subject: |
|
Will using jtag help fix my cfe issue? I never tried jtag so Im not familiar with how it works. Im puzzled as to why Im unable to input any commands, and typing each letter is extremly slow and takes 3-5 tries per letter. Even if i could get a ifconfig and hit enter, it doesnt respond. I dont get another cfe prompt neither. Is this thing f'd? |
|