Problems with RTL8139CL+ and gatework cambria

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> ARM or PPC based Hardware
Author Message
mbaumhof
DD-WRT Novice


Joined: 15 May 2009
Posts: 3

PostPosted: Sun Aug 14, 2011 14:44    Post subject: Problems with RTL8139CL+ and gatework cambria Reply with quote
I have Problems with a Devolo dLAN 200 AV miniPCI
and Cambria GW2358-4.
Built less than 15778 the card is bind to 8139too with the message that the 8139cp mod is better (, but not work)
Builts 16454 or greater the 8139too module did not bind tothe card, and binding to 8139cp the binding is OK, but when I put the eth0 up the message:
8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 13.202456] PCI: enabling device 0000:00:02.0 (0140 -> 0143)
[ 13.209236] 8139cp 0000:00:02.0: eth0: RTL-8139C+ at 0xcb0d2000, 00:0b:3b:27:f8:cc, IRQ 27
[ 57.738682] eth0: link up, 10Mbps, half-duplex, lpa 0x0000
now when I add it to the bridge
8139cp 0000:00:02.0: eth0: PCI bus error, status=8000; PCI expect status 6290

I need the built 17201 because of the WLAN a/n Modules
00:03.0 Network controller: Atheros Communications Inc. AR922X Wireless Network Adapter (rev 01)
00:04.0 Network controller: Atheros Communications Inc. AR922X Wireless Network Adapter (rev 01)

dmesg info:
[ 8.193229] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 8.198626] 8139too 0000:00:02.0: This (id 10ec:8139 rev 20) is an enhanced 8139C+ chip, use 8139cp

any suggestions ?
Michael

By the way, the modules has the same versions 0.9.28 for 8139too and 1.3 for 8139cp
Sponsor
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17485
Location: Hesse/Germany

PostPosted: Mon Aug 15, 2011 13:36    Post subject: Reply with quote
i guess this might be a problem due a kernel upgrade to 2.6.3x .


gimme
Code:
dmesg

_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
mbaumhof
DD-WRT Novice


Joined: 15 May 2009
Posts: 3

PostPosted: Mon Aug 15, 2011 14:29    Post subject: Reply with quote
Here is it:
root@MTS-1 Routerboard2:~# lsmod
Module Size Used by
etherip 4046 0
ebt_dnat 806 0
ebt_snat 902 0
ebt_mark_m 734 0
ebt_mark 790 0
ebtable_filter 1073 0
ebtable_nat 1068 0
ebtables 21912 2 ebtable_filter,ebtable_nat
bonding 72080 0
pata_ixp4xx_cf 2891 0
8250_gw2358 872 0
ad7418 2527 0
cryptodev 10515 0
ocf 16339 1 cryptodev
ixp400_eth 16837 2
ath_mimo_pci 435923 0
ath_mimo_hal 306908 3 ath_mimo_pci
ath_pci 291258 0
ath_hal 221573 1 ath_pci
8139too 20959 0
root@MTS-1 Routerboard2:~# dmesg
0200ff] (PCI address [0x48020000-0x480200ff]
[ 0.238470] bio: create slab <bio-0> at 0
[ 0.238962] vgaarb: loaded
[ 0.239461] SCSI subsystem initialized
[ 0.239654] libata version 3.00 loaded.
[ 0.239850] usbcore: registered new interface driver usbfs
[ 0.239961] usbcore: registered new interface driver hub
[ 0.240193] usbcore: registered new device driver usb
[ 0.240874] Switching to clocksource OSTS
[ 0.241645] NET: Registered protocol family 2
[ 0.241821] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.242204] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.242321] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.242398] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.242412] TCP reno registered
[ 0.242426] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.242457] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.242666] NET: Registered protocol family 1
[ 0.242738] PCI: CLS 32 bytes, default 32
[ 0.243918] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[ 0.243945] fuse init (API version 7.13)
[ 0.244164] msgmni has been set to 244
[ 0.248261] io scheduler noop registered
[ 0.248280] io scheduler deadline registered (default)
[ 0.551477] gpio virtual base c880c000
[ 0.551531] ixp425_gpio: IXP425 GPIO driver loaded
[ 0.551549] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 0.559995] serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
[ 0.970349] console [ttyS0] enabled
[ 0.977336] loop: module loaded
[ 0.980756] nbd: registered device at major 43
[ 0.991984] try to reserve 0x50000000 with size of 0x02000000
[ 0.998196] IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
[ 1.004837] Intel/Sharp Extended Query Table at 0x010A
[ 1.010103] Intel/Sharp Extended Query Table at 0x010A
[ 1.015350] Intel/Sharp Extended Query Table at 0x010A
[ 1.020612] Intel/Sharp Extended Query Table at 0x010A
[ 1.025879] Intel/Sharp Extended Query Table at 0x010A
[ 1.031168] Using buffer write method
[ 1.034822] Using auto-unlock on power-up/resume
[ 1.039431] cfi_cmdset_0001: Erase suspend on write enabled
[ 1.045010] erase region 0: offset=0x0,size=0x8000,blocks=4
[ 1.045024] erase region 1: offset=0x20000,size=0x20000,blocks=255
[ 1.045038] scanning for root partition
[ 1.048865] [0x00000000]
[ 1.051313] [0x00020000]
[ 1.053928] [0x00040000]
[ 1.056540] [0x00060000]
[ 1.059153] [0x00080000]
[ 1.061773] [0x000A0000]
[ 1.064387] [0x000C0000]
[ 1.067000] [0x000E0000]
[ 1.069612] [0x00100000]
[ 1.072232] [0x00120000]
[ 1.074847] [0x00140000]
[ 1.077459] [0x00160000]
[ 1.080079] [0x00180000]
[ 1.082694] [0x001A0000]
[ 1.085306] [0x001C0000]
[ 1.087919] [0x001E0000]
[ 1.090543]
[ 1.090546] found squashfs/jffs2 at 1E0000
[ 1.096288] scan redboot from cafe0000
[ 1.100048] found RedBoot partition at [0x50000000]
[ 1.104954] found RedBoot config partition at [0x51FFF000]
[ 1.110464] found config partition at [0x51FE0000]
[ 1.115262] found linux partition at [0x50080000]
[ 1.119961] Creating 9 MTD partitions on "IXP4XX-Flash.0":
[ 1.125455] 0x000000000000-0x000000080000 : "RedBoot"
[ 1.131853] 0x000000080000-0x000001fa0000 : "linux"
[ 1.138896] 0x0000001e0000-0x000000e00000 : "rootfs"
[ 1.145511] mtd: partition "rootfs" set to be root filesystem
[ 1.151323] 0x000000e00000-0x000001fa0000 : "ddwrt"
[ 1.158007] 0x000001fa0000-0x000001fc0000 : "mampf"
[ 1.164199] 0x000001fc0000-0x000001fe0000 : "nvram"
[ 1.170378] 0x000001fe0000-0x000002000000 : "FIS directory"
[ 1.177239] 0x000001fff000-0x00000201f000 : "RedBoot config"
[ 1.182958] mtd: partition "RedBoot config" extends beyond the end of device "IXP4XX-Flash.0" -- size truncated to 0x1000
[ 1.193922] RedBoot config: unlock failed, writes may not work
[ 1.201037] 0x000000000000-0x000002000000 : "fullflash"
[ 1.208560] PPP generic driver version 2.4.2
[ 1.213398] PPP Deflate Compression module registered
[ 1.218450] PPP BSD Compression module registered
[ 1.224130] PPP MPPE Compression module registered
[ 1.228931] NET: Registered protocol family 24
[ 1.233472] PPPoL2TP kernel driver, V1.0
[ 1.238216] IMQ driver loaded successfully.
[ 1.242450] Hooking IMQ before NAT on PREROUTING.
[ 1.247231] Hooking IMQ after NAT on POSTROUTING.
[ 1.252024] tun: Universal TUN/TAP device driver, 1.6
[ 1.257066] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.263694] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.270346] ixp4xx-ehci ixp4xx-ehci.0: IXP4XX EHCI Host Controller
[ 1.276633] ixp4xx-ehci ixp4xx-ehci.0: new USB bus registered, assigned bus number 1
[ 1.310091] ixp4xx-ehci ixp4xx-ehci.0: irq 32, io mem 0xcd000000
[ 1.330050] ixp4xx-ehci ixp4xx-ehci.0: USB 0.0 started, EHCI 1.00
[ 1.337055] hub 1-0:1.0: USB hub found
[ 1.340882] hub 1-0:1.0: 1 port detected
[ 1.345192] ixp4xx-ehci ixp4xx-ehci.1: IXP4XX EHCI Host Controller
[ 1.351524] ixp4xx-ehci ixp4xx-ehci.1: new USB bus registered, assigned bus number 2
[ 1.380084] ixp4xx-ehci ixp4xx-ehci.1: irq 33, io mem 0xce000000
[ 1.400050] ixp4xx-ehci ixp4xx-ehci.1: USB 0.0 started, EHCI 1.00
[ 1.407062] hub 2-0:1.0: USB hub found
[ 1.410894] hub 2-0:1.0: 1 port detected
[ 1.415388] usbcore: registered new interface driver cdc_acm
[ 1.421094] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[ 1.429729] usbcore: registered new interface driver usblp
[ 1.435218] Initializing USB Mass Storage driver...
[ 1.440272] usbcore: registered new interface driver usb-storage
[ 1.446275] USB Mass Storage support registered.
[ 1.451046] usbcore: registered new interface driver libusual
[ 1.456843] usbcore: registered new interface driver ums-alauda
[ 1.462849] usbcore: registered new interface driver ums-datafab
[ 1.468914] usbcore: registered new interface driver ums-freecom
[ 1.474998] usbcore: registered new interface driver ums-isd200
[ 1.480992] usbcore: registered new interface driver ums-jumpshot
[ 1.487140] usbcore: registered new interface driver ums-karma
[ 1.493041] usbcore: registered new interface driver ums-sddr09
[ 1.499043] usbcore: registered new interface driver ums-sddr55
[ 1.505056] usbcore: registered new interface driver ums-usbat
[ 1.511097] usbcore: registered new interface driver usbserial
[ 1.516983] USB Serial support registered for generic
[ 1.522156] usbcore: registered new interface driver usbserial_generic
[ 1.528683] usbserial: USB Serial Driver core
[ 1.533104] USB Serial support registered for FTDI USB Serial Device
[ 1.539712] usbcore: registered new interface driver ftdi_sio
[ 1.545477] ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
[ 1.551368] USB Serial support registered for GSM modem (1-port)
[ 1.557625] usbcore: registered new interface driver option
[ 1.563219] option: v0.7.2:USB Driver for GSM modems
[ 1.568243] USB Serial support registered for pl2303
[ 1.573334] usbcore: registered new interface driver pl2303
[ 1.578907] pl2303: Prolific PL2303 USB to serial adaptor driver
[ 1.584995] USB Serial support registered for Sierra USB modem
[ 1.590948] usbcore: registered new interface driver sierra
[ 1.596519] sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems
[ 1.603112] i2c /dev entries driver
[ 1.606727] install IXP4XX-I2C.0
[ 1.610214] rtc-ds1672 0-0068: chip found, driver version 0.4
[ 1.616482] rtc-ds1672 0-0068: rtc core: registered rtc-ds1672 as rtc0
[ 1.624390] at24 0-0051: 1024 byte 24c08 EEPROM (read-only)
[ 1.637566] IXP4xx Watchdog Timer: heartbeat 60 sec
[ 1.642494] ixp400: Module init.
[ 1.643124] netem: version 1.2
[ 1.646180] u32 classifier
[ 1.648876] input device check on
[ 1.652660] Actions configured
[ 1.656147] Netfilter messages via NETLINK v0.30.
[ 1.660928] nf_conntrack version 0.5.0 (1952 buckets, 7808 max)
[ 1.667024] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 1.674451] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 1.682371] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 1.688670] nf_conntrack_rtsp v0.6.21 loading
[ 1.693442] nf_nat_rtsp v0.6.21 loading
[ 1.697307] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.702781] IPP2P v0.8.2 loading
[ 1.706027] TCP bic registered
[ 1.709076] TCP cubic registered
[ 1.712316] TCP westwood registered
[ 1.715801] TCP highspeed registered
[ 1.719367] TCP hybla registered
[ 1.722594] TCP htcp registered
[ 1.725730] TCP vegas registered
[ 1.728951] TCP veno registered
[ 1.732091] TCP scalable registered
[ 1.735574] TCP lp registered
[ 1.738534] TCP yeah registered
[ 1.741674] TCP illinois registered
[ 1.745162] NET: Registered protocol family 17
[ 1.749712] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 1.756527] All bugs added by David S. Miller <davem@redhat.com>
[ 1.762564] XScale DSP coprocessor detected.
[ 1.800557] rtc-ds1672 0-0068: setting system clock to 2011-08-14 17:03:07 UTC (1313341387)
[ 1.813975] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.821136] Freeing init memory: 100K
[ 8.193229] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 8.198626] 8139too 0000:00:02.0: This (id 10ec:8139 rev 20) is an enhanced 8139C+ chip, use 8139cp
[ 9.331709] ath_hal: module license 'Proprietary' taints kernel.
[ 9.337725] Disabling lock debugging due to kernel taint
[ 9.361805] ath_hal: 2009-05-08 (AR5210, AR5211, AR5212, AR9160, AR9280, RF5111, RF5112, RF2413, RF5413, RF2425, XR)
[ 9.623660] ath_pci: svn r1202
[ 9.626732] wlan: svn r1202
[ 9.629516] wlan: mac acl policy registered
[ 9.633746] ath_rate_sample: 1.2 (svn r1202)
[ 9.638015] ath_rate_minstrel: Minstrel automatic rate control algorithm 1.2 (svn r1202)
[ 9.646110] ath_rate_minstrel: look around rate set to 10%
[ 9.651594] ath_rate_minstrel: EWMA rolloff level set to 75%
[ 9.657247] ath_rate_minstrel: max segment size in the mrr set to 6000 us
[ 9.842853] ath_mimo_hal: 0.9.17.1 (AR5416, REGOPS_FUNC)
[ 10.175086] ath_mimo_pci: 0.9.4.5 (Atheros/multi-bss)
[ 10.180195] ath_mimo_pci: CR-LSDK-1.4.0.152-DDWRT
[ 10.184894] wlan: 0.8.4.2 (Atheros/multi-bss)
[ 10.189269] wlan: mac acl policy registered
[ 10.193456] ath_rate_atheros: Version 2.0.1
[ 10.193462] Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved
[ 10.205465] PCI: enabling device 0000:00:03.0 (0340 -> 0342)
[ 10.211278] IRQ 26/wifi%d: IRQF_DISABLED is not guaranteed on shared IRQs
[ 10.218111] device id 29
[ 11.776259] ar5416CheckEepromDef: Read Magic = 0xA55A
[ 11.781350] need_swap = True.
[ 11.790643] DFS min filter rssiThresh = 18
[ 11.794746] DFS max pulse dur = 131 ticks
[ 11.799679] 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 11.805838] 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 11.811930] 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
[ 11.816713] 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 11.822806] 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
[ 11.827589] 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 11.833682] 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
[ 11.838468] wifi0: mac 128.2 phy 13.0 radio 12.0
[ 11.843112] wifi0: Use hw queue 1 for WME_AC_BE traffic
[ 11.848335] wifi0: Use hw queue 0 for WME_AC_BK traffic
[ 11.853558] wifi0: Use hw queue 2 for WME_AC_VI traffic
[ 11.858778] wifi0: Use hw queue 3 for WME_AC_VO traffic
[ 11.864001] wifi0: Use hw queue 8 for CAB traffic
[ 11.868699] wifi0: Use hw queue 9 for beacons
[ 11.873053] wifi0: Use hw queue 7 for UAPSD
[ 11.877240] wifi0: Atheros 9280: mem=0x48000000, irq=26 hw_base=0xc89a0000
[ 11.884197] PCI: enabling device 0000:00:04.0 (0340 -> 0342)
[ 11.889995] IRQ 25/wifi%d: IRQF_DISABLED is not guaranteed on shared IRQs
[ 11.896863] device id 29
[ 13.454890] ar5416CheckEepromDef: Read Magic = 0xA55A
[ 13.459976] need_swap = True.
[ 13.469118] DFS min filter rssiThresh = 18
[ 13.473274] DFS max pulse dur = 131 ticks
[ 13.478192] 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 13.484350] 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 13.490442] 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
[ 13.495225] 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 13.501317] 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
[ 13.506101] 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 13.512193] 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
[ 13.516980] wifi1: mac 128.2 phy 13.0 radio 12.0
[ 13.521623] wifi1: Use hw queue 1 for WME_AC_BE traffic
[ 13.526839] wifi1: Use hw queue 0 for WME_AC_BK traffic
[ 13.532062] wifi1: Use hw queue 2 for WME_AC_VI traffic
[ 13.537281] wifi1: Use hw queue 3 for WME_AC_VO traffic
[ 13.542503] wifi1: Use hw queue 8 for CAB traffic
[ 13.547202] wifi1: Use hw queue 9 for beacons
[ 13.551557] wifi1: Use hw queue 7 for UAPSD
[ 13.555743] wifi1: Atheros 9280: mem=0x48010000, irq=25 hw_base=0xc89c0000
[ 13.837377] ixp400_eth: Initializing IXP400 NPE Ethernet driver software v. 1.7
[ 13.844845] ixp400_eth: CPU clock speed (approx) = 665 MHz
[ 13.850554] init port 1, dev 0
[ 13.856382] init port 2, dev 1
[ 18.010073] ixp400_eth: Found PHY 0 at address 1
[ 18.014696] ixp400_eth: Found PHY 1 at address 2
[ 18.410063] ixp400_eth: ixp0 is using NPEC and the PHY at address 1
[ 18.416326] ixp400_eth: ixp1 is using NPEA and the PHY at address 2
[ 18.430905] ixp400_eth: Use default MAC address 00:02:b3:02:02:02 for port 1
[ 18.443112] ixp400_eth: Use default MAC address 00:02:b3:03:03:03 for port 2
[ 18.667787] ad7418 0-0028: ad7418 chip found
[ 18.672970] ad7418 0-0028: configuring for mode 1
[ 18.710139] ixp400_eth:
[ 18.710147] ixp400_eth: ixp0 PHY:1 link up->down
[ 18.912108] ixp400_eth:
[ 18.912116] ixp400_eth: ixp1 PHY:2 link up->down
[ 18.993468] pata_ixp4xx_cf pata_ixp4xx_cf.0: version 0.3
[ 18.999898] scsi0 : pata_ixp4xx_cf
[ 19.003755] ata1: PATA max PIO4 cmd 0x53e00000 ctl 0x53e40006 irq 29
[ 21.460450] br0: starting userspace STP failed, starting kernel STP
[ 22.258140] device br0 entered promiscuous mode
[ 22.846447] device ixp0 entered promiscuous mode
[ 23.230102] ixp400_eth:
[ 23.230110] ixp400_eth: ixp0 PHY:1 link down->up
[ 23.460452] br0: port 1(ixp0) entering learning state
[ 23.486440] device ixp1 entered promiscuous mode
[ 23.570324] device br0 left promiscuous mode
[ 23.580227] device br0 entered promiscuous mode
[ 23.590317] device br0 left promiscuous mode
[ 23.600453] device br0 entered promiscuous mode
[ 24.460102] br0: port 1(ixp0) entering forwarding state
[ 28.402901] device ath0 entered promiscuous mode
[ 28.407707] br0: port 3(ath0) entering learning state
[ 28.854611] bonding: Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
[ 28.862177] bonding: MII link monitoring set to 100 ms
[ 29.410134] br0: port 3(ath0) entering forwarding state
[ 32.530138] Bridge firewalling registered
[ 32.534156] Ebtables v2.0 registered
[ 45.883456] etherip: Ethernet over IPv4 tunneling driver
root@MTS-1 Routerboard2:~# dmesg |grep 8139
[ 1.813975] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 8.193229] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 8.198626] 8139too 0000:00:02.0: This (id 10ec:8139 rev 20) is an enhanced 8139C+ chip, use 8139cp
root@MTS-1 Routerboard2:~# lspci
00:02.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 20)
00:03.0 Network controller: Atheros Communications Inc. AR922X Wireless Network Adapter (rev 01)
00:04.0 Network controller: Atheros Communications Inc. AR922X Wireless Network Adapter (rev 01)
root@MTS-1 Routerboard2:~#
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> ARM or PPC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum