Posted: Mon Mar 07, 2011 18:46 Post subject: Linksys WRT610N v2 + 4g USB device
Hello I have a WRT610N v2 with firmware
Firmware Version DD-WRT v24-sp2 (08/07/10) mega - build 14896
I am trying to use the sierra wireless 250U device with it. It seems to recognize it but I am not able to get it working in 4g mode
I have pasted dmesg when I plug it in through a USB hub because it overcurrents when plugging it in directly
usb 1-1.4.1: new high speed USB device using ehci_hcd and address 6
usb 1-1.4.1: configuration #1 chosen from 1 choice
etherip: Ethernet over IPv4 tunneling driver
eth0: no IPv6 routers present
usbcore: registered new interface driver cdc_ether
usb 1-1: USB disconnect, address 2
usb 1-1.4: USB disconnect, address 3
usb 1-1.4.1: USB disconnect, address 6
usb 1-1.4.2: USB disconnect, address 5
usb 1-1: new high speed USB device using ehci_hcd and address 7
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 7 ports detected
usb 1-1.4: new high speed USB device using ehci_hcd and address 8
usb 1-1.4: configuration #1 chosen from 1 choice
hub 1-1.4:1.0: USB hub found
hub 1-1.4:1.0: 2 ports detected
usb 1-1.4.2: new full speed USB device using ehci_hcd and address 10
usb 1-1.4.2: configuration #1 chosen from 1 choice
usb 1-1.4.1: new high speed USB device using ehci_hcd and address 11
usb 1-1.4.1: configuration #1 chosen from 1 choice
The other device is just power
I have tried using the cdc-ether driver as that was suggested in another post.
I am not sure if theirs a way to paste usb devices.
Joined: 24 Aug 2009 Posts: 2070 Location: South Florida
Posted: Mon Mar 07, 2011 19:28 Post subject:
It's pointless, and 4G is not supported by DD-WRT (AFAIK).
The USB transfer rates from the BCM4718 CPU will be a huge bottleneck on network throughput anyways..
Also, if that USB hub is powered, it will cause major problems. Remove the power from it, then post another dmesg.. _________________ Optware, the Right Way
Asus RT-AC68U
Asus RT-N66U
Asus RT-N10
Asus RT-N12
Asus RT-N16 x5
Asus WL520gU
Engenious ECB350
Linksys WRT600Nv1.1
Linksys WRT610Nv1
Linksys E2000
Netgear WNDR3300
SonicWall NSA220W
SonicWall TZ215W
SonicWall TZ205W
SonicWall TZ105W
hub 1-0:1.0: over-current change on port 1
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 2 ports detected
usb 1-1.2: new full speed USB device using ehci_hcd and address 4
usb 1-1.2: configuration #1 chosen from 1 choice
usb 1-1.1: new high speed USB device using ehci_hcd and address 5
usb 1-1.1: configuration #1 chosen from 1 choice