Belkin F5D8235-4 v2000

From DD-WRT Wiki

Jump to: navigation, search

I have the F5D8235-4 Version: v2000 hardware. This is marketed as the "Belkin N+ Router" and has a full featured USB port. Its firmware is based on Linux 2.6.21.

Here is a dump of the information for it:

# cat /proc/meminfo
MemTotal:        28776 kB
MemFree:          7312 kB
Buffers:          2236 kB
Cached:           9048 kB
SwapCached:          0 kB
Active:           6064 kB
Inactive:         7868 kB
SwapTotal:           0 kB
SwapFree:            0 kB
Dirty:               0 kB
Writeback:           0 kB
AnonPages:        2680 kB
Mapped:           2592 kB
Slab:             5276 kB
SReclaimable:     1164 kB
SUnreclaim:       4112 kB
PageTables:        384 kB
NFS_Unstable:        0 kB
Bounce:              0 kB
CommitLimit:     14388 kB
Committed_AS:     9684 kB
VmallocTotal:  1048404 kB
VmallocUsed:     18012 kB
VmallocChunk:  1029612 kB


# cat /proc/version
Linux version 2.6.21 (XXXXX) (gcc version 3.4.2)

#cat /proc/cpuinfo
system type		: Ralink SoC
processor		: 0
cpu model		: MIPS 24K V4.12
BogoMIPS		: 255.48
wait instruction	: yes
microsecond timers	: yes
tlb_entries		: 32
extra interrupt vector	: yes
hardware watchpoint	: yes
ASEs implemented	: mips16 dsp
VCED exceptions		: not available
VCEI exceptions		: not available

#dmesg
new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered (default)
FLASH_API: MAN_ID=C2 DEV_ID=22CB SIZE=8MB
Ralink RT2880 gpio driver initialized
Gemtek LED init...
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 254
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v1.60  128 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 128, Rx Ring = 128
GDMA1_MAC_ADRH -- : 0x0000000c
GDMA1_MAC_ADRL -- : 0x43305277
PROC INIT OK!
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
ralink flash device: 0x1000000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Ralink SoC physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 5 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00050000 : "uboot"
0x00050000-0x007e0000 : "Kernel and Rootfs"
0x001d0000-0x007e0000 : "Rootfs"
0x007e0000-0x007f0000 : "Nvram"
0x007f0000-0x00800000 : "Factory"
block2mtd: version $Revision: 1.1.1.1 $
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Fully Cone
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
tunl0: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
create_proc_read_write_entry: fail
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 132k freed
Algorithmics/MIPS FPU Emulator v1.5

phy_tx_ring = 0x01cc2000, tx_ring = 0xa1cc2000

phy_rx_ring = 0x00000000, rx_ring = 0x00000000
RT305x_ESW: Link Status Changed
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 790000
rtl8366_smi: module license 'unspecified' taints kernel.
smi_major=249
0 smi_init check[0x05c]1=0x6027
eth2: no IPv6 routers present
Do 'echo 0 > /proc/USB_BLINK;echo 1 > /proc/GPIO23;echo 1 > /proc/GPIO22;' in ixp4xx_gpio.h   
rtl_major = 253
0 smi_init check[0x0105]=0x8366
0 smi_init check[0x0105]=0x8366
Gemtek Link status init.
rtl8366s_getEthernetPHY fail for 5!!!!
rtl8366s_getEthernetPHY fail for 6!!!!
rtl8366s_getEthernetPHY fail for 7!!!!
rtl8366s_getEthernetPHY fail for 8!!!!
rtl8366s_getEthernetPHY fail for 9!!!!
rtl8366s_getEthernetPHY fail for 10!!!!
rtl8366s_getEthernetPHY fail for 11!!!!
rtl8366s_getEthernetPHY fail for 12!!!!
rtl8366s_getEthernetPHY fail for 13!!!!
rtl8366s_getEthernetPHY fail for 14!!!!
rtl8366s_getEthernetPHY fail for 15!!!!
RTL8366RS driver SetVLan initialized
rtl8366s_setMac5ForceLink() initialized!
rtl8366s_getEthernetPHY fail for 5!!!!
rtl8366s_getEthernetPHY fail for 6!!!!
rtl8366s_getEthernetPHY fail for 7!!!!
rtl8366s_getEthernetPHY fail for 8!!!!
rtl8366s_getEthernetPHY fail for 9!!!!
rtl8366s_getEthernetPHY fail for 10!!!!
rtl8366s_getEthernetPHY fail for 11!!!!
rtl8366s_getEthernetPHY fail for 12!!!!
rtl8366s_getEthernetPHY fail for 13!!!!
rtl8366s_getEthernetPHY fail for 14!!!!
rtl8366s_getEthernetPHY fail for 15!!!!
gemtek_switch_reset failed
RTL_GET_GREEN_ETHERNET Success!!!
RTL_GET_GREEN_ETHERNET : tx is 1, rx is 1
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.0, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.1, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.2, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.3, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.4, enabled : 1 !!!
RTL_SET_GREEN_ETHERNET Success!!!
RTL_GET_GREEN_ETHERNET Success!!!
RTL_GET_GREEN_ETHERNET : tx is 1, rx is 1
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.0, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.1, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.2, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.3, enabled : 1 !!!
RTL_GET_GREEN_ETHERNET : rtl8366s_getAsicPowerSaving is phyNo.4, enabled : 1 !!!
2860 version : 2.0.0.0-Win7-20090331 (Jun  9 2009)


=== pAd = c1046000, size = 486296 ===

<-- RTMPAllocAdapterBlock, Status=0
RX DESC a18c0000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff ff 00 00 01
Main bssid = XX XX XX XX XX XX. (removed for privacy reasons)
The UUID Hex string is:XXXXXXXXXXXXXXXXXXXX(removed for privacy reasons)
The UUID ASCII string is:XXXXXXXXXXXXXXXXXXXX(removed for privacy reasons)
<==== RTMPInitialize, Status=0
0x1300 = 00064320
WPS BUTTON press!!
vlan1: Setting MAC address to  XX XX XX XX XX XX. (removed for privacy reasons)
device eth2 entered promiscuous mode
VLAN (vlan1):  Setting underlying device (eth2) to promiscious mode.
vlan1: add 33:33:00:00:00:01 mcast address to master interface
vlan1: add 01:00:5e:00:00:01 mcast address to master interface
vlan1: add 33:33:ff:b2:41:50 mcast address to master interface
vlan1: dev_set_promiscuity(master, 1)
device vlan1 entered promiscuous mode
device ra0 entered promiscuous mode
br0: port 2(ra0) entering listening state
br0: port 1(vlan1) entering listening state
dwc_otg: version 2.60a 22-NOV-2006
DWC_otg: Using DMA mode
dwc_otg lm0: DWC OTG Controller
dwc_otg lm0: new USB bus registered, assigned bus number 1
dwc_otg lm0: irq 18, io mem 0x00000000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
br0: port 2(ra0) entering learning state
br0: port 1(vlan1) entering learning state
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
vlan2: Setting MAC address to  XX XX XX XX XX XX. (removed for privacy reasons)
Close speed boot up led...
ra0: no IPv6 routers present
br0: no IPv6 routers present
vlan1: no IPv6 routers present
WPS BUTTON press!!
WPS_LED_SOLID_BLUE

#cat /proc/modules
dwc_otg 74224 0 - Live 0xc10be000
lm 2720 1 dwc_otg,[permanent], Live 0xc100f000
rt2860v2_ap 931312 1 - Live 0xc1175000 (P)
rtl8366SR 92272 0 - Live 0xc102e000
rtl8366_smi 4672 2 - Live 0xc1006000 (P)