From DD-WRT Wiki
(Difference between revisions)
Revision as of 01:04, 27 February 2008 (edit) Linuxkraft (Talk | contribs)
← Previous diff |
Current revision (14:32, 3 February 2010) (edit) (undo) DHC DarkShadow (Talk | contribs) |
(45 intermediate revisions not shown.) |
Line 1: |
Line 1: |
- | '''How To Flash the WRT54G v8 Using RC5''' | + | #REDIRECT [[Linksys WRT54G v8.0 & v8.2]] |
- | | + | |
- | #Configure your computers local lan ethernet address to 192.168.1.100, subnet 255.255.255.0, gateway 192.168.1.1 . Then connect an Ethernet cable to your computer and port 1 of your WRT54Gv8 router (Do Not Use Wireless). | + | |
- | #Unplug the power cord from the WRT54Gv8. | + | |
- | #Push the reset button while plugging in the power cord and hold the button for about 20 seconds. | + | |
- | #Open your browser and enter into the address bar <nowiki>http://192.168.1.1</nowiki> | + | |
- | #Use the firmware upgrade dialog to flash [http://www.dd-wrt.com/dd-wrtv2/downloads/others/tornado/Gv8/vxworkskillerGv8-v3.bin vxworkskillerGv8-v3.bin]. | + | |
- | #You will see a dialog to Reboot the device. Power cycle the router by unplugging the power cord, then plugging it in. | + | |
- | #Wait for about 1 - 2 minutes. | + | |
- | #You will not be able to browse the WRT54 at this point, but you should be able to ping 192.168.1.1. | + | |
- | #Now it's time to flash the DD-WRT firmware using TFTP | + | |
- | #*If you're on Windows, enter <code>tftp -i 192.168.1.1 put [http://www.dd-wrt.com/dd-wrtv2/downloads/release%20candidates/DD-WRT%20v24%20RC5/GENERIC%20BROADCOM%20(Linksys,%20Asus%20etc.)/WRT54Gv8,%20WRT54GSv7/dd-wrt.v24_micro_wrt54gv8.bin dd-wrt.v24_micro_wrt54gv8.bin]</code> at your <code>cmd</code> shell | + | |
- | #*If you're on Linux, enter <code>tftp -m octet 192.168.1.1 -c put [http://www.dd-wrt.com/dd-wrtv2/downloads/release%20candidates/DD-WRT%20v24%20RC5/GENERIC%20BROADCOM%20(Linksys,%20Asus%20etc.)/WRT54Gv8,%20WRT54GSv7/dd-wrt.v24_micro_wrt54gv8.bin dd-wrt.v24_micro_wrt54gv8.bin]</code> at your shell | + | |
- | #*In Ubuntu Linux I entered atftp --option "mode octet" --verbose -p -l [http://www.dd-wrt.com/dd-wrtv2/downloads/release%20candidates/DD-WRT%20v24%20RC5/GENERIC%20BROADCOM%20(Linksys,%20Asus%20etc.)/WRT54Gv8,%20WRT54GSv7/dd-wrt.v24_micro_wrt54gv8.bin dd-wrt.v24_micro_wrt54gv8.bin]192.168.1.1 | + | |
- | #*If you're on OSX, enter <code>tftp -e 192.168.1.1</code>. At the <code>tftp></code> prompt enter <code> put [http://www.dd-wrt.com/dd-wrtv2/downloads/release%20candidates/DD-WRT%20v24%20RC5/GENERIC%20BROADCOM%20(Linksys,%20Asus%20etc.)/WRT54Gv8,%20WRT54GSv7/dd-wrt.v24_micro_wrt54gv8.bin dd-wrt.v24_micro_wrt54gv8.bin]</code> at your shell | + | |
- | #The file will now be transfered and flashed to your router. After this is done, dd-wrt will automatically boot. You can browse dd-wrt on your router now at <nowiki>http://192.168.1.1</nowiki>. | + | |
- | | + | |
- | If you were having problems with port 4 not working on your router, an upgrade to RC5 will fix that problem. | + | |
Current revision
- REDIRECT Linksys WRT54G v8.0 & v8.2