Linksys E4200

From DD-WRT Wiki

Revision as of 17:53, 1 April 2012 by Basmaf (Talk | contribs)
(diff) ←Older revision | Current revision (diff) | Newer revision→ (diff)
Jump to: navigation, search

Contents

[edit] Hardware Specifications

Image:e4200.jpg


CPU Broadcom BCM4718
CPU Speed 480 MHz
Flash ROM 16 MB
Macronix MX25L12845E
RAM 64 MB
Radios 2.4 GHz, 5 GHz
WLAN Support a/b/g/n
WLAN Max Speed 300mbps (2.4 GHz) & 450mbps (5 GHz)
Antenna Location Internal (x6)
Bands 3 x 3
Switch 4x GigE + 1 WAN
Broadcom 53115
IEEE 802.3/3u/3ab
USB 1x USB 2.0

Radio wl0 is Broadcom 4718 (SoC)

Radio wl1 is Broadcom 4331 Intensi-fi Single-Chip 802.11n Transceiver

[edit] Flashing

[edit] Warnings

  • The E4200 is very sensitive to the nvram size.
  • For the initial flash, upgrading stock firmware to DD_WRT use Flashing process procedure below!! Please follow it to to prevent a brick only use trailed builds
    • A trailed build has "E4200" in its name like: dd-wrt.v24-18777_NEWD-2_K2.6_mini-e4200.bin
  • The only safe builds which can be used AFTER initial flash for this router are nv60 builds
    • A NV60 build in its name like: dd-wrt.v24-18777_NEWD-2_K2.6_big-nv60.bin
  • Recovery from a firmware with the wrong nvram size requires use of a jtag cable to erase the nvram.1
  • Support for the E4200 is still very much a work in progress at this time, outstanding issues reported have included WAN stability, and both 2.4GHz and 5GHz Radio stability.

[edit] Flashing Process

  • Perform these steps when flashing from the stock Linksys GUI:
  1. Read all required reading sections of the peacock announcement: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=51486
  2. Disconnect all cables and wireless clients.
  3. Do a Hard reset or 30/30/30 on router.
  4. Set your computer to a static IP-address 192.168.1.8
  5. Connect 1 Lan cable to pc doing the flash.
  6. Flash the latest E4200 specific mini build E4200 Trailed Initial Flash Build
    • Do NOT use a build with "nv60k" in the name for the initial flash, use only the build linked just above.
  7. Wait for the flashing process to complete.
  8. Wait at LEAST another 5 minutes after the flashing process has completed.
  9. Perform a Hard reset or 30/30/30 after the device has successfully updated.
  10. Wait 3 minutes and log into web interface.
    • You may have to clear your browser cache before the web login will display.

[edit] Upgrading Process

  • If you need to upgrade to a build other then mini or a newer release take note of the following
  • If a nv60 build is flashed to the router those are the only builds which can be flashed from that point on.
    WARNING AFTER installing DD_WRT, ONLY flash -nv60k builds,
    Flashing anything else to the router will brick it as noted above
  1. Select the build of your choosing (Mega, Big, std_usb_nas, OpenVPN, VoIP.)
  2. Follow the same flashing procedure as you used for the initial flash

[edit] Reverting back to stock firmware

  • You can always revert back to stock firmware.
  • Download the latest E4200 firmware from linksys site.
  1. Disconnect all cables and wireless clients.
  2. Perform a 30/30/30 reset on the device.
  3. Login and select the stock firmware file and flash, make sure to select "reset to defaults" on the drop down menu when flashing.
  4. Wait approximately 5 minutes for the flashing process to complete.
  5. Perform a 30/30/30 after the device has successfully updated.

[edit] Wireless-N Configuration

  • Both the 2.4 and 5GHz Radios run at a stock transmitting power of 100mW, decreasing the transmitting power to a value between 40 & 50mW has seemed to help stability.

[edit] References

  1. e4200 build thread at dd-wrt forum
  2. FCC disclosures